LuXout Shades Multi-Channel Controller Manuel utilisateur
INSTRUCTIONS
Multi-Channel Controller
Overview
Multi-Channel Option
Level Control
Touch Sensitive
433 MHz
The LuXout Shades Multi-Channel Controller features a contemporary design with touch sensivite controls. Each battery
and plug-in shade from LuXout Shades will come preprogrammed from the factory. The pre-programming assures the
remote is paired with the shade, the upper and lower operation limits are set, the remote is locked and the unnecessary
channels are hidden for ease of use. (15 available)
Features:
• Up to fifteen channel capacity.
• Touch sensitive buttons.
• Slim Magnetic wall mount.
• LCD display.
• Hide unused channel function.
• Levelling control.
• Individual/group contol.
About The Controller
Package Contents
• Remote
• Magnetic holder &
fixing screws
• Instruction Manual
• 3V - CR2450 Battery
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-47
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LuXout Shades
LuXout Videos
INSTRUCTIONS
Multi-Channel Controller
Overview
Multi-Channel Overview
BACK
Battery
Compartment
(Shown with
cover removed)
FRONT
Multi-
Channel
SLIDE CONTROL
CHANNEL
DOWN
STOP
UP
LCD Screen
TECHNICAL SPECIFICATIONS
Voltage 3V (CR2450)
Frequency 433.92 MHz
Transmitting Power 10 milliwatt
Ambient Operating
Temperature
-10°C - 50°C
Transmission Distance Up to 200 meters
(open spaces)
Battery CR2450
P2P2
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-48
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LuXout Shades
INSTRUCTIONS
Multi-Channel Controller
Overview
Install Wall Mount Holder
Replace cover by pressing snap
latches into place
Use supplied fasteners to attach base to desired
surface as shown in figure
Assure screwdriver slot is facing up or
the controller will not be held in place
securely
Remove cover from base by prying with
flat head screwdriver
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-49
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LuXout Shades
INSTRUCTIONS
Multi-Channel Controller
Initial Setup
Install or Replace Controller Battery
Install battery with
positive (+) side facing up
Replace cover by
reversing step 1
Remove cover from
controller: with 2 fingers
placed in upper area of
cover, press gently in and
down to disengage cover
and slide down to remove
Unlock/Lock Controller - Limit Setting
If limits need adjusting, follow the instructions
below to unlock the controller for limit setting:
• Unlock the limit setting tool by pressing the right
P2 button on the back of the controller (remove
cover to expose the button)
• Press and hold the button until the LED display
shows a flashing “U”, then release.
• You will be required to set the controller back in to
“limit locking mode” once final adjustments have
been made. Simply repeat the above step until a
flashing “L” shows on the display (“U” for un-
locked, “L” for locked).
U
P2P2
Right
P2
‘U’
signifies
unlocked
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-50
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LuXout Shades
INSTRUCTIONS
Multi-Channel Controller
Sleep Mode
Motor head
programming button
Motor head
programming button
It is necessary to “Wake” the motor before operation and setup.
Each battery & plug-in motor comes preprogramed from LuXout Shades. Upon leaving the factory
the motor is placed into “Sleep Mode” to avoid accidental operation during shipping.
WAKE
To “Wake” the motor and exit Sleep Mode, assure the motor is installed and secured in the
mounting hardware.
After the motor is installed in the brackets, press and hold the programming button on the motor head
until the motor jogs up and down once. It is now no longer in “Sleep Mode”and ready for further setup.
* Warning, if you press and release the programming button quickly, the motor will lower to
its lower limit. Be mindful of this during the install process.
SLEEP
If required, to place the motor back into “Sleep Mode” press and hold the programming button
for a period of 6 seconds. Release the button when the motor has jogged up and down twice.
The motor will beep twice to signify “Sleep Mode” has been activated.
Motor head
programming button
Motor head
programming button
Motor Response
HOLD
6
SEC.
JOG
x1 BEEP
x2
JOG
x1
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-51
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LuXout Shades
INSTRUCTIONS
Multi-Channel Controller
Remote & Motor Pairing
Each battery & plug-in motor will come preprogrammed from LuXout Shades. The preprogram-
ming assures the remote is paired with the motor, the upper and lower operation limits are set,
the remote is locked and the unnecessary channels are hidden for ease of use (15 available).
Follow the below steps to select the remote channel you want to pair with the motor(s) if required
at a later date.
Pairing/Removing Motor From A Specific Channel
A). Press any button
to wake controller.
HOLD CH (1 second)
LCD screen will flash
to confirm.
B). Within 4 seconds
Press UP or DOWN
to select desired
channel.
C). Press STOP to
confirm selection
OR controller will
auto confirm
after 4 seconds.
CH
CH CH CH
Motor head
programming button
Motor head
programming button
Press and HOLD
programming button
on motor head for
2 seconds.
Select Channel
Within 4 sec of activating
pairing mode, Press
& Hold STOP.
If you do not pair the controller in time the motor pairing sequence will time out, repeat
the above steps assuring to press and hold the STOP button within 4 seconds of the motor jog.
Motor Response
LONG
BEEP
JOG
x1
x1
HOLD
2
SEC.
Motor Response
BEEP
JOG
x3
x2
HOLD
2
SEC.
CH
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-52
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LuXout Shades
INSTRUCTIONS
Multi-Channel Controller
Reverse Motor Direction
To reverse the motor direction at any time, use the motor operation method shown below.
Motor head
programming button
Hold Programming Button (10 seconds)
Motor head
programming button
HOLD
10
SEC.
JOG
x1 JOG
x1 BEEP
x3
JOG
x1
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-53
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LuXout Shades
INSTRUCTIONS
Multi-Channel Controller
Mirroring Controllers
Motor Response
A). Press any button
to wake controller.
HOLD CH (1 second)
LCD screen will flash
to confirm.
B). Within 4 seconds
Press UP or DOWN
to desired channel.
C). Press STOP to
confirm selection
OR controller will
auto confirm
after 4 seconds.
CH
CH CH CH
1). Select Channel On Existing Controller To Be Copied
2). Add/Remove Controller Using An Existing Controller
Select channel on existing controller to be copied. Select channel on new controller where existing channel
will be copied.
P2P2 P2P2
A). On existing
controller, press left P2
for 1 second.
B). On existing
controller, press left P2
for another 1 second.
C). On new
controller, press left P2
for 1 second.
Motor Response Motor Response
P2P2
BEEP
JOG
x1
x1
HOLD
1
SEC.
BEEP
JOG
x1
x1
HOLD
1
SEC.
BEEP
JOG
x3
x2
HOLD
1
SEC.
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-54
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LuXout Shades
INSTRUCTIONS
Multi-Channel Controller
Adjusting Limits
Adjusting Upper Limits
If limits need adjusting, follow the instructions
below to unlock the controller for limit setting:
• Unlock the limit setting tool by pressing the right
P2 button on the back of the controller (remove
cover to expose the button)
• Press and hold the button until the LED display
shows a flashing “U”, then release.
• You will be required to set the controller back in to
“limit locking mode” once final adjustments have
been made. Simply repeat the above step until a
flashing “L” shows on the display (“U” for un-
locked, “L” for locked).
U
P2P2
Motor Response
Delete Top Limit
Press UP & STOP
5 seconds
Move the shade
to the new desired
position to be set
as limit.
IMPORTANT!! Stop
the shade before traveling
past the desired
lower limit.
Set Top Limit
Press UP & STOP
5 seconds
Motor Response
BEEP
JOG
x1
x1
HOLD
5
SEC.
BEEP
JOG
x3
x2
HOLD
5
SEC.
‘U’
signifies
unlocked
Right
P2
CH CH
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-55
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LuXout Shades
INSTRUCTIONS
Multi-Channel Controller
Adjusting Limits
Adjusting Lower Limits
!!WARNING!! - Move shade in short increments by pressing the UP/DOWN button in 1 second intervals (press-
ing the UP/DOWN button for more than 3 seconds may send the shade past desired upper/lower limit and may
result in damage to the product). Once you have reached the desired upper/lower limit, you can adjust the limit with
either the UP and DOWN buttons. (remember to adjust in short increments!)
Motor Response
CH
Delete Lower Limit
Press DOWN & STOP
5 seconds
Move the shade
to the new desired
position to be set
as limit.
IMPORTANT!! Stop
the shade before traveling
past the desired
lower limit. CH
Set Lower Limit
Press DOWN & STOP
5 seconds
Motor Response
BEEP
JOG
x3
x2
HOLD
5
SEC.
BEEP
JOG
x1
x1
HOLD
5
SEC.
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-56
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LuXout Shades
Autres manuels pour Multi-Channel Controller
1
Table des matières
Autres manuels LuXout Shades Contrôleurs
