Luoman Koppelo 710-2 Mode d’emploi

Luoman Koppelo

710-2

Building instructions

Takuunumero:

Garantinummer:

Garanti nummer

Warranty number:

Le numeró de garantie:

Pidä numero tallessa.

Behåll numret.

Bewahren Sie die Nummer auf.

Hold nummer.

Keep the number.

Le numeró de garantie.

Luoman Puutuote Oy

Lapuantie 626

61450 Kylänpää

Switchboard +358 6 474 5900

asiakaspalvelu@luoman.fi

www.lillevilla.com

ID 11024, Versio 2, Pvm 11/28/2022, LV 710-2

BUILDING INSTRUCTIONS

Foreword

Dear customer,

Thank you for choosing this light log product. Please read the instruction manual carefully in

full before beginning the installation and keep the instructions for further reference. Drawings

of wall constructions and part lists are specific to each model’s own separate instructions.

Warranty terms for this product:

The warranty is void if:

–Assembly instructions are not followed by customer.

–Changes have been made to the parts by customer.

–The package has not been stored properly after delivery to customer.

–The assembled product has not immediately been properly taken care of by painting or other

preservative product.

–The foundation is not made properly, or according to our instructions.

The warranty is valid if:

–A part has a manufacturing defect

–A part is not fit for its intended use.

–A part does not meet the information given prior to purchase.

–A part lasts for a shorter time than can be assumed.

Please check with your local building authorities if planning permission is required before

beginning construction.

Receiving and storing the goods

Machined logs and other parts have been packed into protective wrapping. If the item will not

be constructed immediately, it should be kept indoors or otherwise well-protected until

assembly. The package should be kept away from the ground in order to avoid absorbing

moisture and be stored on a level base.

Transport defects and missing parts must be recorded on the waybill. The delivery is checked

against the waybill when unloading. At the same time, possible transport defects are identified.

Defects and missing parts are recorded on the waybill and immediately reported to the

provider.

For package and transport technical reasons, logs and other timber are placed in the package

so that they form reasonably sized bundles. Therefore, the logs may not be packaged in the

assembly order.

If possible, store the windows and doors indoors.

Please check the contents in full with the help of the part list and contact your retailer

immediately if something is missing or defective.

Please sort the parts near the planned building area leaving enough space for working.

1. Check the content of the packages

ID 11024, Versio 2, Pvm 11/28/2022, LV 710-2

2. Use the part list at the end to register any missing or damaged parts.

3.Contact your retailer if needed.

Procedure in case of defects or faults

If you do have something to complain, please immediately contact the place of purchase to

make a written claim via the re-seller. Inform the reseller about the guarantee number that

can be found on the package. We cannot process a claim without guarantee number. If the

assembling will be begun or continued, it means that the customer has accepted the parts. The

producer and the re-seller reserve rights to decide about all the arrangements concerning the

claim. They may also visit the building site if they think it is necessary. The producer or the re-

seller is not responsible to pay any indirect costs or damages due to a defected or missing

part.

Description of material

Timber is natural material which has some self-evident and ordinary aspects like knots, groups

of knots, splits, crazing in knots, resinous and twisting. This means that loose knots or knot

holes at edges, resin faults, knot and drying splits and crazing not influencing to the

construction are acceptable. Also twisted but usable parts are such. Plane hits and wane at the

back side of roof and floorboards are always acceptable if the faults are not seen at the visible

side when assembled.

Assembly of the building

The builder is responsible for ensuring that the building is fit for its intended use.

Constructing this building requires expertise and thorough knowledge concerning the building

and construction regulations. The builder is expected to comply with good building practices. If

needed, seek advice from experts and construction sector professionals.

The assembly instructions include a parts list, drawings of wall constructions and the required

detail drawings.

To facilitate the identification of the log, the code of the log is marked in the cut-outs of some

logs. Some logs do not have the code, which means that they have to be identified on the

basis of their size and cut-outs. For production technical reasons, some logs have been drilled although

the holes are not needed.

Foundation

The foundation of the building should made on soil that will not move during frozen ground

conditions or sink.

There are several different foundation methods; the foundation should be made in accordance

with the foundation conditions. Seek advice from an expert when choosing and planning the

foundation method. A separate foundation plan should be prepared, when necessary. The

building must be fastened to the foundation. Please bear in mind that the walls must be 5 mm

outside the surface of the plinth in accordance with the drawings.

The measure drawing for the beam foundation is attached to the instructions.

Log frame

Settling of structures is a natural part of log construction, and this should be considered when

planning and assembling the structures. The settling of log structures must be taken into

ID 11024, Versio 2, Pvm 11/28/2022, LV 710-2

account when fastening frame-structured separating walls, stairs, fittings and posts to log

structures. A settling space must be left between unsettled structures and threaded legs must

be used with load-bearing structures. The nominal effective height of the logs is 135 mm.

Some timber is delivered in sawfallen length and must be cut to size at site. Such timber may

be, for example, the roof boards, fascia boards and trims. Pay attention to their correct

jointing points. Parts delivered in such a way are marked in the parts list.

Floor boards are so-called shipping-dry timber and a gap will form in their joints in dry

conditions.

Logs and timber should not get wet during the assembly. If the erection of the building is

interrupted, ensure that the building and its parts are protected.

Pay attention to temporary supports during the assembly.

Lengthening logs

On the long walls, it is necessary to butt logs together by creating a joint between the logs.

The joint should be located in the corner intersection, if possible. The joint is made on the cut-

out using a small nailing plate and screws. If the joint is made carefully, it will not weaken the

wall structure.

Doors and windows

In principle, doors and windows can be added to the building or their places changed.

Contact the reseller.

Reveals at door and window openings

The purpose of the reveals is to stiffen the wall at the openings and at the same time to act as

fastening surfaces for door and window frames. The reveals are assembled on site from a

wooden batten, which is placed in the groove of the log ends, and from a board, which is

fastened with screws to the batten. The reveals allow the wall to settle, and that is why it is

important to leave enough of space above the reveal. Note that there is no groove for the

reveal in the notched logs and that the length of the batten is shorter than the length of the

board of the reveal. The groove for the reveal may need to be machined on site.

Doors and windows are fastened through frames to the reveals. The screws must not hit the

logs as they prevent the logs from settling.

Use an insulator allowing settling when filling the gaps. It is not allowed to use

polyurethane foam!

Settling space for

the reveal batten

Settling space for the frame

and the reveal board

ID 11024, Versio 2, Pvm 11/28/2022, LV 710-2

Spare log

One spare log is included in the delivery. This spare log is intended to be used if a log has a

machining defect or is otherwise damaged or of the wrong size. The spare log must be cut to

size at site. If needed, a cut-out will be made to the spare log at site. The log can be cut to

several spare parts. Note! The cut-out is worked with a handsaw and, for example, a chisel.

Take the measurements and example from a completed cut-out.

Sauna

When building a sauna, the builder must consider the regulations concerning sauna stoves and

chimneys. The requirements set by the sauna stove and chimney have not been considered in

the structures. Sufficient ventilation of the sauna must be ensured. Holes for the air valves

must be made to the outer walls.

Special attention must be paid on the surface treatment of floor boards inside the sauna.

Additional insulation

The delivery does not include thermal insulation. When using thermal insulation, follow the

related instructions and regulations. It is particularly important to pay attention to the vapour

barrier and ventilation, if they are required.

Protection treatment

The timber used for the products LUOMAN products has not been treated. Protection treatment

of the building must be performed immediately after erecting the cabin as soon as the weather

is suitable for it. The first treatment should be done with a with a colorless wood preservative

that prevents the formation of mould and blue stain. Also, the interior of the building must be

treated. Only use wood preservatives that are suitable for log surfaces. Ask for advice of

suitable products from resellers of wood preservatives.

Small black or blue mould spots may easily be formed both on treated and untreated wooden

surfaces in certain conditions. A mould spot is not harmful for the wood nor a defect. It is only

an aesthetic problem that can usually be washed away similarly as dirt. It is also possible to

sand the spots before the surface treatment.

Maintenance

Safe long-term use of the building requires regular checking, possible reparation of the

fastenings and inspecting the condition of the parts. Pay special attention to the roof

construction, its covering material, doors and windows, foundation fastenings, the protection

against storm as well as surface treatment of any wooden parts. Failure to perform regular

maintenance can cause damage to the building or a safety risk to its user.

Regularly inspect the condition of the protection treatment and re-new it when necessary.

Inspect the bottom rails of the doors, windows and their frames, end surface of timbers and

parts stressed by hard weather- or usage-related wearing. Check the functioning of doors and

windows and adjust hinges when necessary. Check the silicon seals of doors and windows,

renewing them when necessary. It is very important to make sure that underneath the

building is well-ventilated. Also installing ventilation grills (not included) on top of the gable

triangles is recommended to let moisture get out from the building.

ID 11024, Versio 2, Pvm 11/28/2022, LV 710-2

Luoman Puutuote Oy

w w w . l i l l e v i l l a . c o m

proj. pvm./date

Luoman 710-2 Koppelo

sisältö/description

log frame dimensions

mittakaava/scale

not in scale

ID 11024, Versio 2, Pvm 11/28/2022, LV 710-2

Luoman Puutuote Oy

w w w . l i l l e v i l l a . c o m

pvm./dateproj.

Luoman 710-2 Koppelo

sisältö/description

wall overhang, space for threaded rod

mittakaava/scale

not in scale

Note! Leave a space to

the foundations for the

threaded rod if needed.

wall overhang from

foundations 5 mm

ID 11024, Versio 2, Pvm 11/28/2022, LV 710-2

Luoman Puutuote Oy

w w w . l i l l e v i l l a . c o m

pvm./dateproj.

Luoman 710-2 Koppelo

sisältö/description

column foundations

mittakaava/scale

not in scale

beam e.g. 48x148

flush with the

upper surface of

the columns, not

included

ID 11024, Versio 2, Pvm 11/28/2022, LV 710-2

Luoman Puutuote Oy

w w w . l i l l e v i l l a . c o m

pvm./dateproj.

Luoman 710-2 Koppelo

sisältö/description

wall drawings

mittakaava/scale

not in scale

drilled for threaded rod

ID 11024, Versio 2, Pvm 11/28/2022, LV 710-2

*not included

Floor beams next to the walls,

fastened to logs with 6x90 mm

screws

Floor beams next to the walls,

fastened to logs with 6x90 mm

screws

waterproofing, e.g.

bitumen strip*

Luoman Puutuote Oy

w w w . l i l l e v i l l a . c o m

pvm./dateproj.

Luoman 710-2 Koppelo

sisältö/description

section, floor

mittakaava/scale

not in scale

beam shoe, fixed with

5x40mm anchor screw

ID 11024, Versio 2, Pvm 11/28/2022, LV 710-2

Table des matières

Autres manuels Luoman Maison de jardin

Luoman

Luoman Playhouse 30 Guide rapide

Luoman

Luoman Lillevilla 54 Guide rapide

Luoman

Luoman Lillevilla Mustikka Guide rapide

Luoman

Luoman Lillevilla 264-1 Guide rapide

Luoman

Luoman Lillevilla Pemu Guide rapide

Luoman

Luoman Lillevilla Mustalampi Guide rapide

Luoman

Luoman Lillevilla 455 Guide rapide

Luoman

Luoman Lillevilla 87 Guide rapide

Luoman

Luoman Lillevilla Pielinen Guide rapide

Luoman

Luoman Lillevilla 321 Guide rapide

Luoman

Luoman Lillevilla 100 C-2 Guide rapide

Luoman

Luoman Lillevilla 578 Guide rapide

Luoman

Luoman Lillevilla 65 Guide rapide

Luoman

Luoman Lillevilla 323 Guide rapide

Luoman

Luoman Lillevilla 85-1 Guide rapide

Luoman

Luoman Lillevilla 97 Guide rapide

Luoman

Luoman Lillevilla Kukkia Guide rapide

Luoman

Luoman Lillevilla 342 Guide rapide

Luoman

Luoman LILLEVILLA Inarijoki Guide rapide

Luoman

Luoman Lillevilla 563 Manuel utilisateur

Luoman

Luoman Lillevilla 319 Guide rapide

Luoman

Luoman Lillevilla 727/ Peippo Guide rapide

Luoman

Luoman Lillevilla 611 Guide rapide

Luoman

Luoman Lillevilla 21 Guide rapide

Manuels Maison de jardin populaires d'autres marques

Mercia Garden Products

Mercia Garden Products 0628LOG181-V4 Manuel utilisateur

Lemeks

Lemeks Palmako PA120-5930-6 Manuel de l'installateur

Gartenhaus-King

Gartenhaus-King Valery Manuel utilisateur

Rion

Rion Hobby Gardener Manuel utilisateur

POD

POD Camping 480 Manuel utilisateur

Select

Select ISAAC E9682 Manuel utilisateur

Mercia Garden Products

Mercia Garden Products 01DTSHPWOR1010DDOW-V4 Manuel d'instructions

Palmako

Palmako Saale Manuel utilisateur

Lemeks

Lemeks Palmako Kira EL16-3623 Manuel de l'installateur

Mercia Garden Products

Mercia Garden Products 0644LOG186-V4 Manuel d'instructions

Palmako

Palmako Roger FR44-5953-2 Manuel utilisateur

Mercia Garden Products

Mercia Garden Products 03DTSHHP1206HGD4MW-V1 Manuel d'instructions

WAR-LOCK

WAR-LOCK GARDENSHED Skillion Series Manuel utilisateur

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Manuel utilisateur

G21

G21 Boston 882 Manuel utilisateur

Lemeks

Lemeks Palmako Grace PM56-4529 Manuel de l'installateur

Mercia Garden Products

Mercia Garden Products 03WES0808-V1 Manuel d'instructions

Shire

Shire Salcey Manuel utilisateur