Luminaire led CMP Series Manuel utilisateur

RETAIN THESE INSTRUCTION FOR FUTURE USE

Page 1of 3

SAFETY PRECAUTIONS

WARNING - Risk of fire or electric shock. Basic safety precautions should always be

followed when using electrical equipment.

WARNING - This product must be installed in accordance with the applicable

installation code by a person familiar with the construction and operation of the

product and the hazards involved.

WARNING - Disconnect power to all circuits before wiring fixture.

WARNING - Install inaccordance with allnational, state, and local codes.

WARNING - The main (white LED) circuit and the auxiliary circuit (Nightlight) are to

be wired to separate circuits that can’t be powered on simultaneously.

WARNING - Do not connect to an ungrounded supply.

WARNING - Read all fixture markings and labels to ensure correct installation of

fixture.

WARNING – Do not apply power to the fixture until the LED Board assembly is

connected to the driver. If power is applied to the fixture prior to connecting the LED

Board assembly to the driver, this will cause the LED Board to fail and void the

warranty.

INSTALLATION GUIDE FOR CMP SERIES

RETAIN THESE INSTRUCTION FOR FUTURE USE

Page 2of 3

CAN ICES-005 (A) / NMB-005 (A)

FCC COMPLIANCE STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his

own expense.

ISED CANADA STATEMENT / DECLARATION POUR ISDE CANADA

This class A lighting equipment complies with Innovation, Science and Economic

Development (ISED) Canada Standard for radio interference-causing equipment ICES-

005, 5th edition.

Ce matériel d’éclairage de classe A est conforme avec la norme sur le matériel

brouilleur radio NMB-005, 5ième édition, publié par innovation, science et

développement économique (ISDE) Canada.

INSTALLATION GUIDE FOR CMP SERIES

RETAIN THESE INSTRUCTION FOR FUTURE USE

Page 3of 3

INSTALLATION PROCEDURE (CMP 12 Shown)

1. Remove Luminaire from carton and inspect for damage.

2. Using tamperproof tool, remove the (6) 10-32 screws from the Housing.

3. Remove the housing by sliding the housing to align the mounting plate retention screws to the

center of the larger diameter section of the hinge mounting slots.

4. Unplug the supply wires from the LED Board Assembly.

5. Remove the LED Board Assembly by loosening (4) 8-32 hex nuts.

6. Mount Fixture to surface using (4) 3/8” bolts (not included).

7. Connect all supply wires in accordance with national and local electrical codes.

8. Re-install LED Board Assembly using (4) 8-32 hex nuts. Do not over tighten.

9. Plug the supply wires back into the LED Board Assembly.

10. Close Fixture by tightening (6) 10-32 screws.

11. Energize and test.

Mounting Plate

Retention Screws

LED Board

Assembly Nuts

Housing Screws

WARNING - The main (white LED) circuit and the auxiliary circuit (Nightlight) are to be wired to separate

circuits that can’t be powered on simultaneously.

Table des matières

Autres manuels Luminaire led Équipement d'éclairage

Luminaire led

Luminaire led CLF11L Manuel utilisateur

Luminaire led

Luminaire led VPF4 Series Manuel utilisateur

Luminaire led

Luminaire led SWP610 Manuel utilisateur

Luminaire led

Luminaire led TSL9 LED Series Manuel utilisateur

Luminaire led

Luminaire led ESF18 Manuel utilisateur

Luminaire led

Luminaire led LVP1212 LED Series Manuel utilisateur

Luminaire led

Luminaire led AEL Manuel utilisateur

Luminaire led

Luminaire led FFW1212 Series Manuel utilisateur

Luminaire led

Luminaire led ARV17/YRV17 LED Manuel utilisateur

Luminaire led

Luminaire led LVP58 Manuel utilisateur

Luminaire led

Luminaire led VPF4 Series Manuel utilisateur

Luminaire led

Luminaire led LVP751 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur