Luma 110 Series Manuel utilisateur
110 Series Mini Bullet
1080p Analog Surveillance Camera
Quick-Start
Guide
2
Luma 110 Series Mini Bullet Camera
Box Contents
}Camera
}Mounting template
}4 wall anchors
}3mm hex wrench
}CC tester cable
You must provide:
}Phillips screwdriver
}Power source: 12V DC
}CC-TV tester (recommended)
3
Luma 110 Series Mini Bullet Camera
Inspection
Ensure that the device is in good condition and
all parts are included. If the product does not
work properly, contact technical support. Do not
disassemble the camera for repair or maintenance.
We recommend installing with RJ59 or RJ6 cabling
with two-wire power (regular or siamese). This
provides better performance over distance than
category cable with baluns.
WARNING: This product can expose
you to chemicals including cadmium,
which is known to the State of California
to cause cancer. For more information
go to www.P65Warnings.ca.gov.
4
Luma 110 Series Mini Bullet Camera
Overview
Before installing, familiarize yourself with the
parts of your camera.
Power
Cable BNC
Video
Cable
Sun
Shield
Lens Infrared
LEDs
Mounting
Base
5
Luma 110 Series Mini Bullet Camera
Prepare for Installation
For your safety:
}Power off all equipment during installation.
}Ensure the wall is strong enough to hold three
times the weight of the camera and the mount.
}If the mounting surface is cement, use the
included expansion screws to install the
camera. If mounting to a wood surface, use
self-tapping wood screws (not included) to
secure the camera.
6
Luma 110 Series Mini Bullet Camera
Install the Camera
1. Drill a cable hole and pilot holes for your screws
in the ceiling, using the supplied template.
2. Route the cables through the cable hole.
3. Secure the base of the camera to the ceiling.
4. This camera has an elbow joint and two rotary
joints for perfect aim. Loosen the two Phillips
screws and the thumb lock at the camera’s base.
5. Adjust the angle of the elbow as desired, and
tighten the elbow screw, A.
6. Rotate the camera so that it faces in the proper
direction, and tighten the base lock, B.
7. Spin the camera casing so that the picture is
level, and tighten the level Phillips screw, C.
8. Connect the power and video cables.
7
Luma 110 Series Mini Bullet Camera
Note that this camera has an OSD menu that can
be accessed through your DVR web interface.
Level
Screw
C
Base
Lock
B
Elbow
Screw
A
8
Luma 110 Series Mini Bullet Camera
Support
866-838-5052 or TechSupport@SnapAV.com
5-Year Limited Warranty
This Luma Surveillance™ product has a 5-Year Limited
Warranty. This warranty includes parts and labor repairs
on all components found to be defective in material
or workmanship under normal conditions of use. This
warranty shall not apply to products that have been
abused, modified or disassembled. Products to be repaired
under this warranty must be returned to a designated
service center with an assigned return authorization (RA)
number. Contact technical support for an RA number.
Copyright ©2015–2019 by SnapAV. All rights reserved.
SnapAV, Luma Surveillance, and all related marks and
images are trademarks or registered trademarks of SnapAV.
Version 181204-1554
Table des matières
Autres manuels Luma Caméra de sécurité
Luma
Luma Special Cube Manuel de service
Luma
Luma 300 Series Manuel utilisateur
Luma
Luma 110 Series Manuel utilisateur
Luma
Luma LUM-600-DOM-A Series Manuel utilisateur
Luma
Luma 300 Series Cube Manuel utilisateur
Luma
Luma 300 Series Manuel utilisateur
Luma
Luma 100 series Manuel utilisateur
Luma
Luma 700 Series Manuel utilisateur
