Lucent Technologies D-182866 Manuel utilisateur

Kit of Parts

503-801-167 (108406828) Issue 2 February 1999 1

TransTalk® 9000 Digital Wireless System

MDW 9031/9031DCP Kit of Parts

Kit of Parts (Order Number D-182866)

This kit contains parts that you must use to install the radio module for a single MDW 9031/9031DCP Wireless

Pocket Phone. You use similar parts that are packaged with the telephone to install the battery charger. Refer to

the installation guide packaged with the telephone for additional information.

Parts List

Installing a Single Radio Module

Install high on wall, leaving at least 6-12 inches (15.2-30.5 cm) between antenna and ceiling.

1 Check to make sure the radio module’s power cord

is unplugged from the wall outlet before

continuing.

2 Detach the four rubber feet. Applythem to marked

areas on the underside of the radio module.

Radio Module 11-foot (3.4 m)

Power Cord and

Standard AC Adapter

Rubber Feet (4)

Philips Head

Wood Screws (2)

Wall Mounting

Plate

Installing a Single Radio Module

Kit of Parts (108406828)

503-801-1672 Issue 2 February 1999

3 Place the wall mounting plate against the wall. Choose a location

backed by a wooden stud (if unavailable, use toggle bolts instead of

the supplied wood screws). Lightly tap a nail into the wall to start

holes. Then screw the plate flush to the wall. Place the radio

module over the plate, then slide it downward to lock it into place.

(Note: Do not remove the plastic cap covering the radio module’s

card edge.

4 Insert the radio module’s power cord into the side of the radio

module. Insert the telephone line cord into the bottom of the radio

module

5 Insert the other end of the telephone line cord into an existing wall

jack or terminal/station connector on your communications system

switch/control unit (refer to your communications system manual

for the proper port location).

6 Plug the power cord/AC adapter into a properly grounded 3-prong

wall outlet.

!CAUTION:

Never connect or disconnect line cords

while the radio module is plugged into

the wall outlet.

TransTalk is a trademark of Lucent Technologies.

Screw

Holes

Radio

Module

POWER

RADIO

PASS

MODULE

206

PFT

MODULE

206

PFT

MODULE

400

PFT

MODULE

400

PFT

PROCESSOR

MODULE

MUSIC

HOLD

VOL

PAGE

SMDR

MUSIC

HOLD

Table des matières

Autres manuels Lucent Technologies Accessoires pour téléphone

Lucent Technologies

Lucent Technologies INDeX 20DS Turret Manuel utilisateur

Lucent Technologies

Lucent Technologies PARTNER Contact Closure Adjunct Manuel utilisateur

Lucent Technologies

Lucent Technologies Definity 8405B Manuel utilisateur

Lucent Technologies

Lucent Technologies PacketStar PSAX 20 Manuel utilisateur

Lucent Technologies

Lucent Technologies LULCST Mode d’emploi

Lucent Technologies

Lucent Technologies SPIRIT 1224 Controller Manuel utilisateur

Lucent Technologies

Lucent Technologies SPIRIT 1224 Controller Manuel utilisateur

Lucent Technologies

Lucent Technologies CIB 3020 Manuel utilisateur

Manuels Accessoires pour téléphone populaires d'autres marques

IAI

IAI CON-T Manuel utilisateur

BT DIVERSE 5400 Manuel utilisateur

Tadiran Telecom

Tadiran Telecom EMERALD ICE Manuel utilisateur

Musicam

Musicam FieldFone II Manuel utilisateur

Polycom

Polycom KIRK KIRK 4040 Fiche technique

TIPTEL

TIPTEL DECT Set 50 Manuel utilisateur

Panasonic

Panasonic KX-UDS124 Manuel utilisateur

BT BT7600 Fiche technique

Panasonic

Panasonic KX-TVP100E Manuel utilisateur

View

View VP-PC Manuel utilisateur

Baldwin Boxall

Baldwin Boxall BT8 Manuel utilisateur

SMC Networks

SMC Networks SMCDPCR-AP Manuel utilisateur

SkyLink

SkyLink SD-001 Manuel utilisateur

Nera

Nera ISDN Manuel utilisateur

MCheeta

MCheeta CT-CID803 Plus Manuel utilisateur

YASKAWA

YASKAWA YRC1000 Manuel utilisateur

Intellitouch

Intellitouch MOH-500E Manuel utilisateur

Viking

Viking SQRG-12 Instructions d'utilisation