LUCCI ARENA II Manuel utilisateur

Installation Instructions

1 | P a g e v 1 . 0 p u b l i s h e d o n 0 7 . 2 0 1 7

ARENA II FLOOD LIGHT WITH SENSOR

SKU# 240711, 240713, 240715, 240717

Rated Voltage 220-240V~ 50Hz

Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all

instructions carefully before assembly, installation and use. Please keep instructions for future reference.

Warranty

•This light fitting is covered by a 3 year warranty. The warranty is from date of purchase, not the date of installation.

•If the fitting is not installed by a licensed electrician the warranty will be void.

•Please retain proof of purchase and evidence of installation by a licensed electrician.

•Warranty will be void if there is any damage due to improper usage or modification to the fitting.

•Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void

warranty.

•This fitting is not suitable for use with dimmer switches. Warranty will be void if the fitting is used on the same circuit

which has a dimmer switch.

Installation requirements

•Must be installed by a licensed electrician.

•All wiring and installation of the light fitting must adhere to local and national wiring rules.

eg. AS/NZS 3000:2007/Amendment 2:2012 Electrical installations.

•This fitting contains floating tempered glass. Replace any cracked protective glass to maintain IP rating when

using this fitting.

•Select a suitable location for installation;

- This product is suitable for indoor and outdoor use.

- The mounting point must support 2 times the weight of the fitting.

- This fitting is protected against water penetration to IP44 standards, which is splashing in every direction.

- This fitting must not be mounted on a surface which can be subject to vibrations.

- Take note of the directional marking on the fitting before installation.

•Take care not to pull any electrical wires during unpacking as this may damage the connection.

•Lay out all the components on a smooth surface and make sure there are no components missing before

assembling. If parts are missing, return the complete product to the place of purchase for inspection or

replacement.

•Check whether the fitting has been damaged during transport. Do not operate/install any product which appears

damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.

•Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

PIR sensor information

PIR (PASSIVE INFRA-RED) SENSOR:

The fitting has a PIR (Passive Infra-Red) sensing device which continuously scans the operating zone and immediately

switches the light on when it detects movement in that area. Whenever movement is detected within the range of the

sensor, the light will switch on automatically to illuminate the area. While there is movement within the sensor range,

the light will remain on.

Installation Instructions

2 | P a g e v 1 . 0 p u b l i s h e d o n 0 7 . 2 0 1 7

SENSOR LOCATION & INFORMATION:

To find a suitable location for installation, please take into consideration the following points:

•The ideal mounting height for the fitting is between 1.8m to 2.5m above the detection area (Fig. 1).

•The detection area is approximately 8m away at an angle of 120° wide. This may vary depending on the mounting

height and location.

•The detection area may also alter at different temperatures. PIR sensors are more sensitive in cold weather than

warm weather.

•The sensor has better sensitivity with movement across the detection area (Fig. 2).

•The sensor has reduced sensitivity with movement towards and away from the detection area (Fig. 3).

•If movement is made walking directly towards or away from the sensor and not across, the apparent detection

range will be substantially reduced.

•To avoid false triggering, the sensor should be directed away from potential heat sources, such as barbecues, air-

conditioners, air vent etc.

•Also avoid areas with electromagnetic disturbance, outside lighting, moving cars, trees or pets etc.

•Avoid installing the fitting in close proximity or on the same circuit to any fluorescent light fittings or ceiling fans.

RFI (Radio Frequency Interference) may cause the fitting to switch on unintentionally.

•Do not aim the sensor towards reflective surfaces, such as smooth white walls, swimming pools etc.

•To avoid damage to the sensor, do not aim the sensor towards the sun.

•It is recommended that the fitting is installed on its own switch and does not interconnect with other lights on the

same switch as it may cause false triggering.

Installation directions

1. Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

2. Remove the mounting bracket from the body of the fitting by loosening the screws. Fig. 1

3. Use the mounting bracket as a template to mark the screw positions onto the wall. Fig. 2

Drill holes into the wall and push the plastic anchors into the holes. Fig. 3

4. Install the mounting bracket onto the wall by using appropriately sized mounting screws, plastic washers and

anchors. Ensure the screws, plastic washers and anchors used are suitable for the mounting surface. Fig.4, 5

5. Install the fitting back onto the mounting bracket. Fig.6

Installation Instructions

3 | P a g e v 1 . 0 p u b l i s h e d o n 0 7 . 2 0 1 7

6. Connect the mains supply wire and fitting power cord to an IP44 rating terminal block (Not included). Ensure that

the wires are secure and no bare wires are exposed. Additional silicon may need to be added to maintain the

IP44 rating of the fitting. Fig. 7

Mains Supply Wire Wiring Label

Earth – Yellow/Green Yellow/Green

Neutral – Blue or Black N (Neutral)

Live – Brown or Red L (Live)

7. Adjust the LED body and PIR sensor to the desired position.

8. Switch the power to circuit back ON only after all electrical work has been fully completed and the fitting is fully

assembled and is ready to use for the first time.

SENSOR SETTINGS:

DURATION TIME: The length of time the light will remain switched on after

activation can be adjusted from 12secs ±5 to 6mins ±2. Rotating the time knob

from (+) to (-) will reduce the duration time.

NOTE: Once the light has been triggered by the PIR sensor, any subsequent

detection will start the timed period again from the beginning, the light will remain

on until there is no movement detected.

ADJUSTING THE SENSITIVITY: The sensitivity means the maximum distance

which PIR Sensor can be triggered by body movement. Turning the SENS knob + to - will decrease the sensitivity.

LUX LEVEL: The lux control module has a built-in sensing device (photocell) that detects daylight and darkness. The

() position means that the fitting will work at both day and night. The () position will only work at night.

NOTE: If you want to test the detection area of the PIR sensor, please wait for the ambient light level is below 5 lux.

SENSOR TESTING:

1. Put the LUX control knob to the light () position and the TIME control knob to minimum (-).

2. Direct the sensor toward the desired area to be scanned by twisting the sensor left and right.

3. Have someone walk across the centre of the area to be scanned and slowly adjust the angle of the sensor until

the fitting can sense the moving person and causes the light to switch on.

4. Adjust the TIME control knob to the desired length of time for the fitting to remain on.

5. Adjust the LUX control knob to achieve the ideal ambient light for the fitting to switch “on”.

For the fitting to switch ‘on’ when the ambient light is darker, switch the LUX control knob from () to ().

For the fitting to switch ‘on’ when the ambient light is brighter, switch the LUX control knob from () to ().

Installation Instructions

4 | P a g e v 1 . 0 p u b l i s h e d o n 0 7 . 2 0 1 7

You may need to make further adjustments to achieve your ideal light level setting.

Note: There is no override function for this fitting.

Trouble shooting

PROBLEM

POSSIBLE CAUSE

Manuels Projecteur populaires d'autres marques

VIZULO

VIZULO Micro Martin Guide de l'utilisateur

EuroLite

EuroLite LED IP FL-100 SMD Manuel utilisateur

Cooper Wheelock

Cooper Wheelock XB12 Manuel utilisateur

Allen + Roth

Allen + Roth 17624-000 Manuel utilisateur

ADJ

ADJ 4 STAGE PAK Manuel utilisateur

Cooper Lighting

Cooper Lighting EGL91SW233 Manuel utilisateur

Max

Max 37496 Manuel utilisateur

BEGA

BEGA 85 143 Manuel utilisateur

Beamz

Beamz 151.226 Manuel utilisateur

EuroLite

EuroLite LED IP FL-8 Manuel utilisateur

Ledj

Ledj PERFORMER 36 RGB Manuel utilisateur

Perel

Perel ELS3 Manuel utilisateur

Perel

Perel ELS3WD Manuel utilisateur

LumX

LumX LM 36130 Manuel utilisateur

Xtricity

Xtricity 4-80053 Manuel utilisateur

Stahl

Stahl 6521/4 Series Manuel utilisateur

Ecosense

Ecosense EcoSpec Manuel utilisateur

Ayrton

Ayrton minipanel FX Manuel utilisateur