LUCCI Air SUMMIT Series Manuel utilisateur

V1.0-AU (08/2021)

LUCCI

SUMMIT SERIES

DC CEILING FAN

INSTALLATION

OPERATION

MAINTENANCE

WARRANTY INFORMATION

CAUTION

READ INSTRUCTIONS CAREFULLY FOR SAFE

INSTALLATION AND FAN OPERATION.

Airfusion Summit Installation Instructions

1 | P a g e

THANK YOU FOR PURCHASING

Thank you for purchasing the latest in energy-saving ceiling fans. This fan runs on DC (direct current) power

which gives it the benefit of being super energy efficient while still maintaining high volume air movement and

silent operation.

Energy-saving - The DC motor is the latest technology in fan design. Its highly efficient motor saves up to

65% more energy than ceiling fans with traditional AC motors.

Silent operation – This DC fan motor is programmed with a stabilised current which efficiently reduces motor

noise.

Low operating temperature – The DC power is managed effectively which brings down the motor operating

temperature to less than 50℃. This results in a much cooler motor than a standard AC fan and increases the

longevity of the motor.

6-speed remote control - Regular AC ceiling fans usually come with only 3 speeds, and this DC fan comes

complete with a 6 speed remote, which gives a greater choice of comfort levels.

SAFETY PRECAUTIONS

1. The appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for their safety.

2. Children should be supervised to ensure that they do not play with the appliance.

3. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local wiring

rules.

IN AUSTRALIA

WARNING:

FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION

MUST BE INCORPORATED INTO THE FIXED WIRING IN

ACCORDANCE WITH THE WIRING RULES.

As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the minimum

electrical safety of this standard.

Please note warranty will be void if the installation is without a means for

an all-pole disconnection incorporated in the fixed wiring in accordance

Airfusion Summit Installation Instructions

2 | P a g e

with the wiring rules.

Example: If a fan is connected to a circuit that can be isolated via an all-

pole safety switch at the switchboard, then this is considered to be an

all-pole disconnection to the ceiling fan electrical circuit, meeting the

requirements of clause 7.12.2 of AS/NZS 60335.1.

A single-pole switch on the active of the receiver input of remote

control must also be included in the wiring, and located the same

room as the ceiling fan.

4. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.

Contact your local government for information regarding the collection systems available. If electrical

appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater

and get into the food chain, damaging your health and well-being.

5. The structure to which the fan is to be mounted must be capable of supporting four times the weight of

the fan.

6. The fan should be mounted so that the blades are at least 2.3 m above the floor in Europe or 2.1 m above

the floor in Australia.

7. This fan is suitable for indoor and alfresco areas where the fan is fully undercover with a minimum of 2

walls. This fan is not waterproof. When installed in an alfresco area, the ceiling fan must be positioned in

a location protected from water, wind, dust and salt. Exposure to these elements will void the warranty.

Mounting the fan in a situation where it is subject to water or moisture is dangerous and may increase the

risk of damage, injury or electrical shock.

8. Must be assembled and installed by a licensed electrician.

9. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the ceiling

fan and contact the manufacturer, its service agent or suitably qualified persons.

10. The replacement of parts of the safety suspension system device shall be performed by the manufacturer,

its service agent or suitably qualified persons.

11. The fixing, which means the attachments to the ceiling via hooks or other devices must have sufficient

strength to withstand four times the weight of the ceiling fan; that the mounting of the suspension system

shall be performed by the manufacturer, its service agent or suitably qualified persons.

Airfusion Summit Installation Instructions

3 | P a g e

PARTS LIST

•Unpack your ceiling fan carefully. Remove all parts and hardware.

•Lay out all the components on a smooth surface and make sure no components are missing before

assembling. If parts are missing, return the complete product to the place of purchase for inspection or

replacement.

•Check whether the ceiling fan has been damaged during transport. Do not operate/install any product

which appears damaged in any way. Return the complete product to the place of purchase for inspection,

repair or replacement.

•Examine all parts, and you should have the following:

Fig. 1

Airfusion Summit Installation Instructions

4 | P a g e

INSTALLING THE FAN

TOOLS REQUIRED:

- Phillips / flat head screwdriver

- Pair of pliers

- Adjustable spanner

- Step ladder

- Wirecutter

- Wiring, supply cable as required by local provincial and national wiring codes and regulations

INSTALLING THE MOUNTING BRACKET

•The ceiling fan must be installed in a location so that the blades are spaced 300mm from the tip of the

blade to the nearest objects or walls.

•Install the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least four

times the weight of the fan, using the two long screws provided. Ensure at least 30mm of the screw is

threaded into the support. (Fig. 2)

NOTE: The bracket screws provided are for use with wooden structures only. For structures other

than wood, the appropriate type of screw MUST be used. Ensure the screws used are suitable for the

mounting surface and the surrounding environment.

ANGLED CEILING INSTALLATION

The hanging system of this fan is ONLY suitable for flat ceiling installation.

DO NOT install the fan on an angled ceiling.

Fig. 2

four times of the weight of the fan

Airfusion Summit Installation Instructions

5 | P a g e

INSTALLATION OF BLADE (Fig.3)

1. Unscrew the 4 screws from the cover of the fan blade and lift the blade cover; (Fig.3.1)

2. Install the fan blades onto the motor assembly; (Fig.3.2)

3. Install the cover back to the motor assembly by tightening the 4 screws. (Fig.3.3)

Fig. 3.1

Fig. 3.2

Airfusion Summit Installation Instructions

6 | P a g e

Fig. 3.3

Airfusion Summit Installation Instructions

7 | P a g e

HANGING OF THE FAN (Fig.4)

1. Place the hanger onto the mounting bracket. Ensure the key slot of the hanger ball is positioned on the

key pin of the mounting bracket to prevent the fan from rotating when in operation; (Fig.4.1)

2. Install the drive component onto the hanger by pushing through the mounting bracket; (Fig.4.2)

3. Connect the wiring (Fig.4.3 & Refer to the wiring diagram in Fig.5 for more information)

- Connect the supply cable from the terminal block to the input of the drive component.

- Connect the output of the drive component to the cable of the fan assembly.

- Connect the earth wire to the earth terminal.

- Ensure the earth terminal is tightened to maintain the earth continuity.

4. Check and ensure all wiring connections are secured. (Fig.4.4)

Fig. 4

Fig. 4.1 Fig. 4.2

Fig. 4.3 Fig. 4.4

Airfusion Summit Installation Instructions

8 | P a g e

WIRING DIAGRAM (FIG. 5)

WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A

LICENSED ELECTRICIAN.

NOTE: AN ADDITIONAL ALL-POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED

WIRING.

NOTE: IF THERE ARE TWO OR MORE DC CEILING FANS INSTALLED IN THE ONE LOCATION, AN

ISOLATION SWITCH IS REQUIRED FOR EACH CEILING FAN. THIS IS REQUIRED WHEN

PROGRAMMING THE REMOTE AND RECEIVER TO PAIR TOGETHER.

Ensure the motor earth wire is connected to the single earthing terminal block “1” in the diagram below.

(Fig. 7)

From mains supply to mounting bracket terminal block:

1. Connect the live supply wire to the “L” terminal of the terminal block on the mounting bracket.

2. Connect the neutral supply wire to the “N” terminal of the terminal block on the mounting bracket.

3. Connect earth wire to the earth terminal of the terminal block on the mounting bracket.

From mounting bracket to receiver and motor:

4. Connect the supply wiring from the mounting bracket to the input of the DC motor driver remote receiver.

5. Connect the output wires of the DC motor driver/receiver to the input wires of the fan motor.

NOTE: Do not connect the light terminal to the output of the driver. The light function is not applicable

to this model.

Fig. 5

Airfusion Summit Installation Instructions

9 | P a g e

FINISHING THE INSTALLATION

INSTALLATION OF THE CANOPY (Fig.6)

1. Ensure the earth wiring is secure and correct, by performing an earthing continuity test from the fan’s

accessible metal body back to the earth terminal at the terminal block on the mounting bracket.

2. Push the canopy up to the ceiling canopy top cover fixed by two screws and the clicks;

3. Lock the bottom cover of the canopy by turning anti-clockwise.

Fig. 6

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels LUCCI Air Ventilateur

LUCCI Air

LUCCI Air AIRFUSION MOTO LD-MOTO-52 Guide d'installation

LUCCI Air

LUCCI Air Nordic Manuel utilisateur

LUCCI Air

LUCCI Air AIRFUSION AKMANI Guide d'installation

LUCCI Air

LUCCI Air AIRFUSION CAROLINA Guide d'installation

LUCCI Air

LUCCI Air Airfusion Radar Manuel utilisateur

LUCCI Air

LUCCI Air AIRFUSION FLUSSO Manuel utilisateur

LUCCI Air

LUCCI Air AIRFUSION GIRONA Manuel utilisateur

LUCCI Air

LUCCI Air ATLANTA LD-56 ATL Guide d'installation

LUCCI Air

LUCCI Air Breeze 16 Guide d'installation

LUCCI Air

LUCCI Air AIRFUSION CAROLINA Guide d'installation

LUCCI Air

LUCCI Air AIRFUSION CLIMATE II Manuel utilisateur

LUCCI Air

LUCCI Air ESPERANCE Series Manuel utilisateur

LUCCI Air

LUCCI Air AIRFUSION AIRLIE II ECO Manuel utilisateur

LUCCI Air

LUCCI Air AIRFUSION BALI LD-BALI-52 Manuel utilisateur

LUCCI Air

LUCCI Air FIJIAN II Series Manuel utilisateur

LUCCI Air

LUCCI Air AIRFUSION AIRLIE II ECO Series Guide d'installation

LUCCI Air

LUCCI Air BREEZE 8 Guide d'installation

LUCCI Air

LUCCI Air ARRAY Manuel utilisateur

LUCCI Air

LUCCI Air AIRFUSION BREEZE TRIPOD FAN Manuel utilisateur

LUCCI Air

LUCCI Air PUMA Manuel utilisateur

LUCCI Air

LUCCI Air ATLANTA Manuel utilisateur

LUCCI Air

LUCCI Air AIRFUSION UNIONE-56 ORB Manuel utilisateur

LUCCI Air

LUCCI Air Aria CTC Manuel utilisateur

LUCCI Air

LUCCI Air AIRFUSION ARIA CTC Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage