Lorex ACSOL2 Series Manuel utilisateur
Solar Panel
Quick Start Guide
ACSOL2 Series
lorex.com
En
Package contents
User-supplied tools
• Solar panel with 10ft (3m) power cable
• Wall mount
• Wall mount template
• Wall mount screws & anchors (×4)
• Adjustment ring screws (x2)
• 1/4” (6mm) Drill bit for cement and wood
• Cable guides, screws & anchors (×3)
• Velcro cable tie
• Drill
• Phillips screwdriver
1
Dimensions
4.7"
120mm
4.5"
115mm
5.4"
137mm
2
7”
178mm
6.1”
156mm
1”
25mm
2.9”
73mm
Solar panel
Front and side panel
Wall mount
Front and side view
Position the solar panel
• The solar panel produces power only when exposed
to sunlight. You will need to choose a location with
plenty of direct sunlight.
• To achieve the best charging performance, angle
the solar panel towards the sun. The optimal
angle varies throughout the year, depending on the
seasons and your location. As a general guideline,
the solar panel should be facing the equator; in the
northern hemisphere, the solar panel faces south
and in the southern hemisphere, the solar panel
faces north.
• Make sure the red LED indicator on the back of
the solar panel turns on (see Figure 1). If the LED
turns on, the solar panel is receiving enough light to
maintain the camera battery pack’s charge.
3
Figure 1:
Back panel
3WattSolar Panel
ModelNo.:ACSOL2-CT
Power: 3.00 W
Voltage: 5.10 V
LOREXTEC HNOLOGYINC.
www.lorex.com
20181200001 Made in China
Red LED indicator
Tip: Periodically clean the solar panel with a soft
cloth and warm water to keep the surface clear.
Select your installation method
Install your wire-free camera directly
onto the solar panel, see pages 8-11.
4
Install your wire-free camera and solar
panel separate from each other, see
pages 5-7.
Option A (recommended):
Installing the solar panel separately
Option B:
Installing the solar panel and
camera together
ATTENTION: For option B, the camera
and solar panel should be installed facing the
residence. If the camera is installed backing
onto the residence, the wall mount may block
the wireless signal.
4
Option A - Installing the solar panel separately
1. The solar panel is designed
to maintain the camera
battery pack’s charge. Make
sure to rst charge the
battery pack using the micro
USB cable.
2. Stick the wall mount
template in the desired
mounting position.
3. Drill into the wall mount
template’s marked holes
using the 1/4” (6mm) drill bit.
If attaching to masonry,
gently tap four anchors into
the holes.
4. Secure the wall mount using
four screws (see Figure 1).
5
Figure 1
6
5. Loosen the wall mount’s adjustment
ring by turning it counterclockwise
(see Figure 2).
6. Angle the rotating adjustment screw
45° away from the mounting surface
(see Figure 2).
7. Twist the solar panel onto the wall
mount. Be careful not to hit the
mounting surface.
8. Adjust the angle of the solar panel to
receive direct sunlight, then tighten
the adjustment ring.
9. Use a Phillips screwdriver and the
adjustment ring screw to secure the
adjustment ring from underneath the
wall mount (see Figure 2).
Adjustment ring
Figure 2
Option A - Installing the solar panel separately
7
10. Run the solar panel’s power cable along
the cable guide on the wall mount arm
(see Figure 3).
11. Pull up the power port cover on the back
of your camera.
12. Use the solar panel’s power cable to
connect to the power port (see Figure 3).
Option A - Installing the solar panel separately
Figure 3
Figure 4
Optional cable management:
• Use the adjustable Velcro cable tie to
secure cords and organize any clutter.
• Secure the solar panel’s 10ft (3m) power
cable to the wall using the cable guides,
screws, and anchors as needed
(see Figure 4).
Option B - Installing the solar panel and camera together
1. The solar panel is designed to
maintain the camera battery pack’s
charge. Make sure to rst charge the
battery pack using the micro USB
cable.
2. Stick the wall mount template in the
desired mounting position.
3. Drill into the wall mount template’s
marked holes using the 1/4” (6mm)
drill bit. If attaching to masonry,
gently tap four anchors into the holes.
4. Secure the wall mount using four
screws (see Figure 1). 8
ATTENTION: The camera can be installed onto the solar panel only if the camera is
facing the residence. If the camera is installed backing onto the residence, the wall mount may
block the wireless signal. We recommend installing the solar panel and camera separately, see
pages 5-7.
Figure 1
Table des matières
Langues :
Autres manuels Lorex Panneau solaire
