Longray 2680A2 Manuel utilisateur

Longray

User Manual

Longray Carryall Super-Duty Cold ULV Fogger

2680A2

Solution Tank Cover Power Switch

Nozzle Flow Adjust Dial

Solution

Tank

Heavy-duty

Flex-hose

Su er-duty

Motor

Contents

1 Warnings 2

2 About your fogger 3

2.1 Overview.............................. 3

2.2 Techspecs............................. 3

3 Operation 4

3.1 Prep ................................ 4

3.2 Tobeginspraying ......................... 4

3.3 Tostopspraying.......................... 4

4 Care and maintenance 5

4.1 Cleaning .............................. 5

4.2 Long-termStorage......................... 5

4.3 Wearandtear ........................... 5

5 Troubleshooting 6

5.1 Motor doesn’t start . . . . . . . . . . . . . . . . . . . . . . . . 6

5.2 Motor starts, but no spray . . . . . . . . . . . . . . . . . . . . 6

1 Warnings



Do not turn the machine upside-down.



After use, empty the solution tank and spray water 1-2 minutes to clear

the solution pipeline. This is especially important for corrosive chemicals.



When cleaning the machine, don’t splash water onto the motor and power

switch.



Do not operate if the power cord or power switch insulation is damaged.



Strongly corrosive chemicals may damage the machine.



Do not allow corrosive gas to enter the machine through the air intake,

otherwise motor damage can occur.



Be careful where you point the nozzle while you adjust the solution output.

2 About your fogger

2.1 Overview

Your Ultra-Low Volume (ULV) fogger is equipped with a motor that produces

high speed airﬂow, driving solution particles through a specially designed nozzle.

The nozzle emits extremely ﬁne fog droplets, 5-50 microns in diameter, small

enough to linger in the air for a long time.

AC powered. More powerful than battery-powered foggers, and quieter than

gasoline-powered thermal foggers.

Ergonomic design. Handheld nozzle, ﬂex-hose, and carrying strap designed for

comfort and eﬃciency.

Flow control. Use the ﬂow control knob to adjust ﬂow rate. (Droplets will also

be slightly smaller at lower ﬂow rates.)

2.2 Tech specs

Model 2680A2

Capacity 1.6 gal

Motor 800 W

Output

Droplet Size 5-50 micron

Solution ﬂow rate 0.0-6.3 gal/hr

Spray distance 15 ft

Physical

Dimensions 18.9 x 8.5 x 9.6 in

Dimensions, shipping 22.5 x 9.2 x 13.5 in

Weight 8.8 lb

Weight, shipping 12 lb

3 Operation

3.1 Prep

1. Wear protective clothing/gloves/masks in accordance with safety regula-

tions.

2. Check power cord insulation.

3. Make sure power switch is OFF.

4. Make sure ﬂow adjust knob is at 0.

5. Add chemical into the tank, diluting if necessary, following the chemical

manufacturer’s documentation.

6. Tighten the lid to prevent pressure leaks.

3.2 To begin spraying

1. Plug into wall outlet.

2. Turn power switch to ON.

3. Wait for the motor to spin up.

4. To start spraying, turn ﬂow adjust knob to 1 or more. Always keep the

fogger upright.

3.3 To stop spraying

1. Turn ﬂow adjust knob to 0. Do this before turning oﬀ power switch.

2. Wait until the spray stops, then turn power switch to OFF. If you want to

start machine again, wait until the motor spons down. Rapid power cycling

can shorten motor life.

3. Unplug from wall outlet.

4. Follow the steps in 4.1 Cleaning to clean the tank and solution pipeline.

This is especially important for corrosive chemicals.

4 Care and maintenance

4.1 Cleaning

1. Empty any chemical from the tank.

2. Clean the tank: add water, tighten the lid and shake.

3. Clean the solution pipeline: start the machine and spray 1-2 minutes.

4. Turn oﬀ the unit and empty the rinse water from the tank.

4.2 Long-term Storage

1. Follow the steps in 4.1 Cleaning to clean the machine.

2. After emptying the tank of rinse water, dry the tank and pipeline by running

the machine for 1-2 minutes with an empty tank.

3. Store the unit in a dry, well-ventilated location.

4. Leave the solution lid open.

4.3 Wear and tear

Moving parts should be lubricated every 3-6 months to prevent corrosion and

oxidation. If any hoses, gaskets, and O-rings become cracked, brittle, or stiﬀ,

replace immediately.

5 Troubleshooting

5.1 Motor doesn’t start

1. Make sure power switch is ON.

5.2 Motor starts, but no spray

1. Make sure the ﬂow-rate adjust knob is not at 0.

2. Check the solution level in the tank.

3. Check the tank lid is tight.

4. Check the rubber gasket under the tank lid. If the gasket is missing or

loose, there may be a pressure leak, and the unit will not spray.

5. Look for the solution intake tube at the bottom of the tank.

6. The ﬁlter at the end of the intake tube may be clogged. Rinse out or

replace the ﬁlter.

7. Fill the solution tank to 2/3 full with water and try again.

Table des matières

Autres manuels Longray Équipement de lutte contre les insectes

Longray

Longray TS35N Manuel utilisateur

Longray

Longray Pioneer Manuel utilisateur

Manuels Équipement de lutte contre les insectes populaires d'autres marques

Gardigo

Gardigo 66643 Manuel utilisateur

Starkeys

Starkeys L25 Manuel utilisateur

Stinger

Stinger Nosquito CT100 Series Manuel utilisateur

Radarcan

Radarcan R-502 Manuel utilisateur

FarmTek

FarmTek Growers supply 115106S Manuel utilisateur

Gardigo

Gardigo MOSQUITO-KILLER Manuel utilisateur

Radarcan

Radarcan MICE REPELLER HOME Manuel utilisateur

Orno

Orno OR-AE-13111 Manuel utilisateur

Fogmaster

Fogmaster FOG-001 Manuel utilisateur

Bettio

Bettio Picoplis maxi Manuel utilisateur

DynaTrap

DynaTrap DT150 Manuel utilisateur

Ultrasound Tech

Ultrasound Tech ZeroZzz AIR Manuel utilisateur

Olimpia electronics

Olimpia electronics RT-52/HACCP Manuel utilisateur

MistAway

MistAway GEN III Manuel

One Stop Gardens

One Stop Gardens SOLAR INSECT KILLER 95500 Guide de référence rapide

Dynamic

Dynamic Dynatrap XL Manuel utilisateur

Stinger

Stinger BKC40 Series Manuel d'utilisation et d'entretien

Agrimate

Agrimate AF-4000NK-VM Manuel utilisateur