Logik MZB 15 SS Manuel utilisateur

Table of Contents

1. Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . .

2. Preparing your ice maker for use. . . . . . . . . . . . . . . . . . . .

A. Important safety tips . . . . . . . . . . . . . . . . . . . . . . .

3. Parts and Description . . . . . . . . . . . . . . . . . . . . . . . . . . .

4. Operating procedures & maintenance . . . . . . . . . . . . . . .

A. Unpacking your ice maker . . . . . . . . . . . . . . . . . . .

B. Connecting your ice maker . . . . . . . . . . . . . . . . . .

C. Cleaning and maintaining your ice maker. . . . . . .

5.Usingyouricemaker............................

6. Technical parameters & circuit diagram . . . . . . . . . . . . .

A. Technical parameters. . . . . . . . . . . . . . . . . . . . . .

B.CircuitDiagram..........................

7.Troubleshooting...............................

8.PartsDiagram........................

8/9

Ice

Maker

ADD WATER ICE FULL

SELECT

ON/OFF

Instruction Manual

Important safety instructions: read carefully and keep for future reference.

ICE MAKER

Model : MZB 15 SS

1. Important Safety Instructions

Your Safety and the safety of others is very important.

We have provided many important safety measures in your manual

and on your appliance.

Always read and obey all safety measures.

This is the safety alert symbol

All safety measures will follow the safety alert symbol and the word

“DANGER” or “WARNING”

These words mean:

You can be seriously injured if you don’t immediately follow instructions.

All safety measures will inform you of potential hazards, how to reduce

the chance of injury and what can happen if the instructions are not

followed.

DANGER

WARNING

2. Preparing your ice maker for use

IMPORTANT SAFETY TIPS

When using electrical appliances, basic safety precautions should be

followed to prevent the risk of fire, electric shock, and injury to persons

or property. Read all instructions before using any appliance.

- Do not operate this or any other appliance that has a damaged cord.

Connect to properly polarised outlets only. No other appliance should

be plugged into the same outlet. Ensure that the plug is fully inserted

into the receptacle

- Do not run cord over carpeting or other heat insulators. Do not cover

the cord. Keep cord away from high traffic areas, and do not submerge

in water.

- We do not recommend the use of an extension cord, as it may overheat

and become a fire hazard. If you must use an extension cord, use a No.:

14 AWG minimum size and rated no less than 1875 watts.

- Unplug the ice maker before cleaning or making repairs.

- Exercise caution and use reasonable supervision when appliance is

used near children.

- Do not clean your ice maker with flammable fluids. The fumes can

create a fire hazard or explosion.

- Do not tip over

- If the ice maker is brought in from outside in winter, give it a few hours

to warm up to room temperature before plugging it in.

CAUTION: Plastic bags can be dangerous. To avoid danger of

suffocation, keep this bag away from babies and children.

WARNING: This appliance must be earthed

IMPORTANT: The wires in this mains lead are coloured in accordance

with the following code

Green / Yellow : Earth

Blue: Neutral

Brown: Live

3. Parts and Description

1. Cover: With a transparent window to allow interior visibility.

2. Ice Scoop

3. Ice Shovel

4. Control Panel

5. Ice Basket

6. Fan Vent

7. Water Drain Cap:

To drain

water from

the reservoir

Control Panel

A) “Add Water” Indicator Light

B) Selection Button

C) Power Button

(to turn unit on and off)

D) “Full Ice” Indicator Light

E) Ice Size Indicator Light

L = Large Size Cubes

M = Medium Size Cubes

S = Small Size Cubes

Ice Maker

ADD WATER

FULL ICE

SELECT

ON/OFF

4. Operating Procedures & Maintenance

A. Unpacking your Ice Maker

1. Remove the exterior and interior packaging. Check that the ice basket

and ice scoop are included. If any parts are missing, please contact

our customer service centre.

2. Clean the interior with lukewarm water and a soft cloth. Take out the

basket and clean it.

3. Find a location for your ice maker that is protected from direct sunlight

and other sources of heat (i.e: stove, furnace, radiator). Place the ice

maker on a level surface. Make sure that there is at least 13 cm of

space between the back and sides of your ice maker and the wall.

4. Allow at least one hour for the refrigerant fluid to settle before plugging

ice maker in.

5. The appliance must be positioned so that the plug is accessible.

B. Connecting your Ice Maker

* Improper use of the earthed plug can result in the risk of electrical shock.

If the power cord is damaged please call our customer service centre.

1. This unit should be properly earthed for your safety. The power cord

of this appliance is equipped with a three prong plug which mates with

a standard three prong wall outlet to minimize the possibility of electric

shock.

2. Plug your appliance into an exclusive, properly installed, earthed wall

outlet. Do not under any circumstances, cut or remove the third (earth)

prong from the power cord. Any questions concerning power and/or

earthing should be directed toward a certified electrician.

3. This appliance requires a standard 220 ~ 240 volt, 50Hz electrical

outlet with three prong earth.

Before using your ice maker, it is strongly recommended to clean it

thoroughly

DANGER

C. Cleaning and Maintaining Your Ice Maker

Before using your ice maker, it is strongly recommended to clean it

thoroughly and on a regular basis.

1. Remove the ice basket.

2. Clean the interior with diluted detergent, warm water and a soft cloth.

3. Rinse thoroughly with water. Drain water from the Ice Maker by

unplugging the drain cap on the side.

4. The outside of the ice maker should be cleaned regularly with a mild

detergent solution and warm water.

5. Dry the interior and exterior with a soft cloth.

6. If the machine is not in use for a long period of time, ensure all water

is drained from the Ice Maker via the drain cap.

7. Always ensure that the Drain Plug and Cap are securely replaced.

5. Using Your Ice Maker

1. Select the size required of the ice cube by pressing the “Select” button.

If the room temperature is lower than 15°C, it is recommended to select

the small or medium ice sign button in order to avoid the ice sticking

together.

2. Open the cover, remove the ice basket and pour water into tank.

Keep the water level below the maximum water level mark.

3. Press the “Power” button on the control panel to begin the ice making

cycle.

4. The ice making cycle lasts approxiamtely 6 to 15 minutes, depending

on the size of the ice cube selection and the ambient temperature.

Ice production may vary due to the ambient temperature

5. While the ice maker is on, check the water level regularily. If the water

pump cannot inject water into the ice bucket, the ice maker will stop

automatically, and the “Add Water” indicator will come on. Press the

“Power” button, fill water up to the maximum water level mark and

press the “Power” button again to turn on the unit again.

NOTE: Allow the refrigerant liquid inside the compressor at least 3

minutes to settle before restarting.

6. The ice maker will automatically stop working when the ice basket is

full and the “Ice” indicator light will come on.

7. Change the water in the water reservoir every 24 hours. If the unit

isn’t in use, drain all water left in the tank.

7A. Technical Parameters

Model MZB 15 SS

Climate Type SN/N/ST

Protection Type I

Power 200V ~ 240V/50Hz

Ice Making Current 1.0A

Ice Harvest Current 1.6A

Refrigerant R134a/65g

Net Weight 12.6 kg

Vesicant C5H10

Enclosure Stainless Steel

7B. Circuit Diagram

)

ELECTRICAL

DIAGRAM

FOR ICEMAKER

POWER

SUPPLY

TRANSFORMER

WATER

ICE

LED3

LED1

LED2

SET

LED6

ON/OFF

MCU

MAIN CONTROL PCB

RELAY RELAY

RELAY

AC-N

AC-L

COMP

VALVE VALVE

OVERLOAD

PROTECTOR

COMPRESSOR

START RELAY

SOLENOID

VALVE

-PUMP+

+ FAN -

MICROSWITCH

WATER DETECTING

DEVICE

SENSOR FOR

COOLING

FAN MOTOR

SENSOR FOR ICE

FULL DETECTING

DC FAN MOTOR

DC WATER PUMP

MOTOR FOR ICE SHOVEL

Ice cubes are

sticking together

The ice cycle is too long

Stop the ice maker, and restart

it after the ice blocks melt.

Select the small ice button

Water temperature in

inner tank is too low

Change the water in the inner

tank. Temperature of water

should be between 8˚C & 32˚C

PROBLEM PROBABLE CAUSE SOLUTION

The ice making

cycle is normal

but no ice is

being produced

Ambient temperature or

water temperature in

the inner tank is too high

Refrigerant liquid

leakage

Pipe in the cooling

system is blocked

Ambient temperature

surrounding the unit is above

32 °C, move to a cooler area

and replace water in the

tank with cooler water

Please contact the service

agent

Please contact the service

agent

“Water” indicator

light is on

Lack of water in the

reservoir

Stop the icemaker, fill with

water and then restart the

ice maker

“Ice” indicator is on There is too much ice in

the ice basket

Remove ice from the ice

basket

The “Water” & “Ice”

indicator lights are

flashing

The ice shovel cannot

move

Check the ice shovel to ensure

there is no obstruction,

otherwise consult a qualified

technician

7. Troubleshooting

Warranty Terms : 12 Months

Packed for Game (Masstores (Pty) Ltd

214 West Street, Durban, 4001

8. Parts Diagram

1. Inner Tank

2. Ice Bucket

3. Evaporator Assembly

4. Bottom Base

5. Condensor

6. DC12V / Fan Blade

7. Rear Protection Board

8. Electrical Box

9. Rear Strengthening Board

10. Rubber Feet with bolts

11. Main Control PWB

12. Transformer

13. Power Cord Clip

14. Sychronous Motor

15. Back Down Cover

16. Inner Tank Fixing Piece

17. Micro Switch

18. Ice Shovel

19. Electromagnet Valve Assembly

20. Refrigerant Dry Filter

21. Front Panel

22. Water Draining Assembly

23. Rear Panel

24. Support for Sensor

25. Ice Basket

26. Back Up Cover

27. Front Up Cover

28. Front Down Cover

29. Down Window

30. Up Window

31. Compressor

32. Steel Grill

33. Operation Panel Frame

34. Water Filter

35. Water Detecting Piece

36. Up Sponge for Compressor

37. Down Sponge for Condensor

38. Fixing set for water pump

39. DC12V / Water Pump

40. Power Supply cords

41. Button PWB

42. Silicon pipe for suppyling water

43. Silicon pipe for ice bucket

Table des matières

Autres manuels Logik Machine à glaçons

Logik

Logik ZBJ 15 S Manuel utilisateur

Manuels Machine à glaçons populaires d'autres marques

Hoshizaki

Hoshizaki KMD-460MWJ Manuel utilisateur

Sub-Zero

Sub-Zero 315I Instructions d'utilisation

Unold

Unold 48945 Manuel utilisateur

Kenmore

Kenmore 2217402A Manuel utilisateur

Cornelius

Cornelius WM600 Mode d'emploi

GE XPIO43SCSS Manuel utilisateur

Hoshizaki

Hoshizaki KMD-901MAH Manuel utilisateur

Whynter

Whynter FIM-450HA Manuel utilisateur

U-Line

U-Line UMCR014-SC01A Manuel d'installation

Andrew James

Andrew James AJ000522 Manuel utilisateur

Scotsman

Scotsman CME1356 Manuel utilisateur

Scotsman

Scotsman ACM 25 Manuel utilisateur

Kärcher

Kärcher IP 120 Manuel utilisateur

U-Line

U-Line SS1095 Manuel utilisateur

Maytag

Maytag MIM1554WRS - Ice Maker Manuel utilisateur

Hoshizaki

Hoshizaki KM-630MAH Manuel utilisateur

Princess

Princess Yonanas Manuel utilisateur

Unold

Unold 48946 Manuel utilisateur