Logic Controls LS6000 Manuel utilisateur

Logic Net eStation

Kitchen Video Controller with Ethernet Interface

USER MANUAL AND

INSTALLATION GUIDE

LS6000

NOTICE

The manufacturer of the Industrial Computer makes no representations or warranties, either

expressed or implied, by or with respect to anything in this manual, and shall not be liable for

any implied warranties of fitness for a particular purpose or for any indirect, special or

consequential damages. Information in this document is subject to change without notice and

does not represent a commitment on the part of the manufacturer.

FCC NOTICE

This device complies with Part 15 of FCC Rules. Operations are subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

EUROPEAN COMMUNITY (CE) MARK OF CONFORMITY

This product is in conformity with the protection requirements of EU Council Directive

89/336/EEC on the approximation of the laws of the Member States relating to

electromagnetic compatibility. Logic Controls cannot accept responsibility for any failure to

satisfy the protection requirements resulting from a non-recommended modification of the

product. This product has been tested and found to comply with the limits for Class A

Information Technology Equipment according to CISPR 22 / European Standard EN 55022.

The limits for Class A equipment were derived for commercial and industrial environments to

provide reasonable protection against interference with licensed communication equipment.

Warning:

This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

LOGIC CONTROLS, INC.

355 Denton Ave

New Hyde Park, NY 11040

TEL: (516) 248-0400

FAX: (516) 248-0443

Email: [email protected]

http://www.logiccontrols.com

IMPORTANT SAFETY INSTRUCTIONS

Please read the following instructions carefully and save these instructions for future

reference.

1. Follow all warnings and instructions for installation and operation of the product.

2. Unplug this product from the wall outlet before cleaning. Use only mild cleaning

agents and do not immerse in water.

3. Do not use this product near water.

4. This product should be operated from the type of power indicated on the power

adaptor. If you are not sure of the type of power available, consult your dealer or local

power company.

5. Do not allow anything to rest on the power cord. Do not locate this product where

persons will walk on the cord.

6. If an extension cord is used with this product, make sure that the total ampere rating of

the equipment plugged into the extension cord does not exceed the extension cord

ampere rating. Also, make sure that the total rating of all products plugged into the

wall outlet does not exceed the fuse rating.

7. We recommend all servicing done on this product be done by qualified service

personnel. Aside from upgrades or swapping out the compact flash please refer all

other servicing to the Logic Controls RMA Dept or a repair provider that has been

certified by Logic Controls.

8. Unplug this product from the wall outlet and refer servicing to qualified service

personnel under the following conditions:

a) When the power cord or plug is damaged or frayed

b) If liquid has been spilled into the product

c) If the product has been exposed to rain or water

d) If the product does not operate normally when the operating instructions are

followed. Adjust only those controls that are covered by the operating

instructions since improper adjustment of other controls may result in damage

and will often require extensive work by a qualified technician to restore the

product to normal condition.

e) If the product has been dropped or the cabinet has been damaged

f) If the product exhibits a distinct change in performance, indicating a need for

service.

iii

TABLE OF CONTENTS

FEATURES .........................................................................................................1

PRODUCT DESCRIPTION..................................................................................3

CONNECTOR PINOUTS.....................................................................................5

HARDWARE INSTALLATION ............................................................................6

LS6000 SETUP AND SELF-DIAGNOSTIC TESTS ............................................7

SYSTEM SETUP ...............................................................................................10

TROUBLE SHOOTING .....................................................................................11

SOFTWARE DEVELOPMENT ..........................................................................13

SPECIFICATIONS.............................................................................................14

FEATURES

The LS6000 Logic Net eStation is the Ethernet version of Logic Net, the industry’s leading

kitchen video display system solution. It has succeeded the advantages of Logic Net and yet

facilitates network implementation with the most popular Ethernet connections.

» Highly Reliable

• No complex PC work stations

• Low power operation, low internal temperature rise

• Simple hardware and no disk drive (no moving parts)

• Reliable latched interface connections

• Rugged die-cast housing

• Standard Ethernet network connection

• Stable operation, no computer crashes, viruses, and lockups

• Tamper proof, no on/off and option switches, no adjustable devices

» Low Cost

• PC workstations NOT required

• Network software NOT required

• Network cards NOT required

• I/O expansion hardware NOT required

• Simplified installation and setup

» Advanced Operations

• 256 text foreground and background color

• Icon display continuously showing connection status of Ethernet and keyboard

• Touch-screen support

• Status line display for showing status, messages, help items, alerts, or on-screen touch

function keys (with touch screen support enabled).

• Beep tone pitch controllable in command such that each station can beep with different

pitch for easier identification

• 16 automatic timers individually displayable at any location on the screen

• 4 display modes (40-column, 60-column, 80-column and 106-column)

• Display bit-map files for build-card display support

» Embedded Custom Functions

• Embedded custom functions available through downloadable firmware upgrade

• Executes complex sequence of operations with a single command from the server

• Reduces application software burden

• Performs real-time tasks more efficiently for enhanced system throughput

» Small Size

• Module size: 6.3"W x 5.1"L x 1.0"H (160 x 130 x 25mm)

• Flexible Installation: Table Mount, Wall Mount, Display Bracket Mount, and Under-the-

Counter Mount

» Highly Secure

• Designed to prevent illegal data copying through externally accessible removable media.

The internally installed compact flash (optional) is for picture storage. Program code and

data are not stored in the compact flash.

• Enhanced security through proprietary command set

• Immune to viruses

» Minimize Obsolescence Problems

• Upgrade LS6000 units with remote downloadable firmware and character fonts

» Extensive Free Software Development Support

• High-level language software utilities allow developers to write application software with

Visual Basic or Visual C++

• OCX control covers all of the Logic Net's command sets

• Multi-tasking programs are supported

• Command test program with source code to illustrate the applications of the command set

• Source code of mini-applications to answer all how-to-write questions

• Free phone and e-mail technical support

» Self-diagnostic

• Automatic power-on and diagnostic tests for:

- Internal Memory

- Communication Integrity

- Keyboard Connection

- RS232 ports

- Internal Beeper

» Compatible OS

• Compatible with servers operating in:

- DOS

- Linux

- Unix

- Windows 95/98/ME

- Windows NT/2000/XP

» International Operations

• Downloadable code pages support languages for international operations

• Universal input (100 to 240VAC, 47 to 63Hz) switching power supply

PRODUCT DESCRIPTION

A typical system consists of a host server (PC or POS terminal) where the application

software is installed and a number of LS6000 Logic Net eStation units. Each LS6000 unit can

be connected to a VGA monitor, a keyboard, and 2 serial interface devices. The LS6000

units communicate with the host server via TCP sockets on Ethernet connections. Logic Net

commands are sent from the server to display data on the eStation VGA monitor and to read

key codes of keys entered on the keyboard.

RESET Button

Press the RESET button located on the front of the LS6000 to reset the unit and access

Setup or self-diagnostic tests.

Power/Status LED

The power/status LED is located on the front of the LS6000. A light indicates that power is

ON. When communicating with the host server, the LED will blink.

Speaker/Beeper

The beeper function is controlled by host software applications. The frequency of the beeper

tone can be adjusted from the LS6000 Setup screen.

Keyboard

An RJ-11 to PS2 adapter will connect the LS6000 to a standard PC keyboard. Other

keyboard wedge interface input devices such as Bumpbars, Bar-Code Scanners or Magnetic

Stripe Readers can also be connected to the LS6000. The Logic Controls KB1700 Bumpbars

are specially designed for use in the kitchen. Refer to the KB1700 manual for more

information on the bumpbar.

Displays: Monochrome or Color VGA

LS6000 supports any standard color or monochrome VGA CRT or LCD display using a

standard 15-pin DSUB VGA connector.

RS-232 Devices

The two auxiliary RS-232 ports on the LS6000 supports connections to serial printers, touch

screens*1, barcode scanners, and other serial interface I/O devices. The first serial port is a

standard 9-pin DSUB connector. The second port is an RJ45 connector with EIA-561 pin out.

Power Requirements

The power supply for LS6000 is same as the one used for LM3000 and LS3000. The power

supply is designed for single-phase, sinusoidal ac operation and accepts a wide input range

that does not require intervention to change between low- and high-voltage AC. Operation at

any voltage within these ranges will meet the output requirements and will not cause damage

to the supply. The power supply output is connected to the LS6000 with locking connectors.

Nominal Voltage: 100–240 V AC

Voltage Variation: 90–265 V AC

Frequency: 47–63 Hz

*1 - Custom driver code in firmware is required for supporting different models of touch

screens and will be available in future versions of LS6000. Currently, Elo touch

screens are supported.

CONNECTOR PINOUTS

Ethernet interface (8 pin RJ45 connector with 2 LED indicators)

1 TX-

2 TX+

3 RX-

6 RX+

RS-232 interface (9 pin DSUB male connector)

1 DCD

2 RX

3 TX

4 DTR

5 GND

6 DSR

7 RTS

8 CTS

RS-232 interface (8 pin RJ45 connector – EIA-561 pin out)

1 DSR

2 DCD

3 DTR

4 GND

5 RXD

6 TXD

7 CTS

8 RTS

Keyboard interface (6 pin RJ-11 connector)

1 CLK

2 DATA

3 No connection

4 Signal GND

5 +5 V dc

6 Chassis GND

VGA interface (15 pin DSUB female connector)

1 Red

2 Green

3 Blue

5,6,7,8 &10 GND

13 H-Sync

14 V-Sync

DC Power (Shielded snap lock mini-DIN connector with EMI/RFI suppression)

5 +5 V dc

8 +5 V dc

3 GND

6 GND

1 5

6 9

HARDWARE INSTALLATION

Component Placement

The following is recommended when you plan the Logic Net setup:

•Place the LS6000 so that you can use the mounting brackets located at the bottom of

the unit.

•Place the LS6000 so that the RESET button is accessible.

•Place the LS6000 so that the beeps from the speakers can be heard.

•Place the LS6000 so that the LED indicator on the front panel can be seen.

•Place the LS6000 above grill/counter level, out of the way of possible spills.

Mounting Instructions

Mounting brackets are provided to facilitate mounting the LS6000 to a wall, ceiling or display

monitor mounting arm. The installer should insure that the wall anchors used with the

mounting brackets have the capacity to support 4.3 kg (9.5 lb.). This weight is determined by

adding a safety margin weight to the weight of the unit. Wall anchors with specified weight

capacity are available commercially.

Connections

Make sure that all systems are powered off before making or removing any connections to the

LS6000 unit. Follow the steps below in connecting the devices:

1. Connect the VGA cable of the display monitor to the LS6000.

2. Connect the RS232 cable of serial devices to the LS6000.

3. Connect the keyboard device to the LS6000.

4. Connect the Ethernet cable from Ethernet hub or switch to the LS6000.

5. Connect power to all peripheral devices and turn on power.

6. Connect power adapter to the LS6000 and power cord to the power adapter.

7. Plug the power cord into AC power outlet.

8. If necessary, reset the LS6000 by pressing the reset button.

Autres manuels pour LS6000

Table des matières

Autres manuels Logic Controls Contrôleurs

Logic Controls

Logic Controls LS6100 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur