Loctite 883976 Manuel utilisateur

EQUIPMENT

Operation Manual

LoctiteDigital Syringe Dispenser

Part Number 883976

Benutzerhandbuch

LoctiteDigitales

Kartuschendosiergerät

Artikelnummer 883976

Manual de operación

LoctiteDosificador

digital tipo jeringa

Número de parte 883976

TableofContents 2

1. Safety - Please Observe the Following 3

1.1 Emphasized Sections

1.2 For Your Safety

1.3 Unpacking and Inspection

1.4 Items Supplied

2Description 4

3TechnicalData 6

4Installation 6

5Operation 7

5.1 Set up Instructions

Manual Mode

5.2 Dispense Cycle Setting

Time Mode

Incremental Mode with Teach Function

Cycle Counter Reset

6Troubleshooting 10

7 Maintenance & Operational Tips 11

8 Accessories and Spare Parts 11

9 I/O Configuration & Pneumatic Diagram 12

10 Warranty 13

11 Declaration of Conformity 15

1 Please Observe The Following

1.1 Emphasized Sections

Warning!

Refers to safety regulations and requires safety measures that

protect the operator or other persons from injury or danger to

life or property

Caution!

Emphasizes what must be done or avoided so that the unit or

other property is not damaged.

Notice:

Gives recommendations for better handling of the unit

during operation or adjustment as well as for service

activities.

1.2 For Your Safety

For safe and successful operation of the unit, read these

instructions completely. If the instructions are not observed,

the manufacturer can assume no responsibility.

Do not operate the unit in excess of rated capacities.

Do not use the unit to dispense flammable or corrosive

fluids.

Do not use in wet or exposed environments.

Observe general safety regulations for the handling of

chemicals such as Loctite®adhesives and sealants. Observe

the manufacturer’s instructions as stated in the Material

Safety Data Sheet (MSDS).

Make sure the Unit stands stable and secure.

1.3 Unpacking and Inspection

Carefully unpack the Loctite®Digital Syringe

Dispenser and examine the items contained in the

carton. Inspect the unit for any damage that might

have occurred in transit. If such damage has

occurred, notify the carrier immediately. Claims for

damage must be made by the consignee to the carrier

and should be reported to the manufacturer.

1.4 Items supplied

(1) Digital Syringe Dispenser 883976

(1) Universal Power Cord and Adapter

902520

(1) Foot Switch 902521

(1) Syringe Stand 901459

(1) 10ml and (1) 30ml Airline Adapter

(1) Dual Unit Stacking Lock Pin 8900574

(1) Air line Support Mast 8900575

(1) Needle Sample Kit

(1) Inlet Air Hose (6mm OD x 6ft) & Fitting

Kit 902523

2 Description

The Loctite®Digital Syringe Dispenser 883976 is semi

automatic dispensing system designed for adhesives and

fluids packaged in syringe barrels. The unit has digital

timing control, with decimal control to .001 seconds for

increased precision over typical pressure time systems. An

adjustable pressure regulator controls a pulse of air, and

when used in conjunction with a airline adapter attached to

an adhesive syringe barrel, it will provide a controlled

dispense of that adhesive. Additional features include

Vacuum suck-back that can effectively control

product dripping or stringing.

Timed or Incremental Mode to allow adhesive to be

applied at once or in an incremental fashion.

Convenient “Teach Mode” to help determine time

required when the dispense amount is not known.

Cycle counter option displays clearly in LCD screen

The unit can also be integrated into PLC

programming to facilitate a continuous operation.

2.1 Feature Descriptions

Fig 2.1

Items Description Items Description

1 Power Button 9 Receiver head air hose mast

2 Mode Button 10 Foot Switch Receptacle

3 Set up/Save Button 11 Power Receptacle

4 Display 12 I/O Connection

5 Air Pressure Gauge 13 Exhaust Port

6 Air Pressure Regulator 14 Air Inlet

7 Pulsed Air Outlet 15 Cord Lock

8 Vacuum Control

10 12

Digita l Syringe Dis penser

S/N:

Please refer to the instruction

CAUTION:

www.equipment.loc tite.com

manualbefore installation

MADEINCHINA

Sicherheit

geprufte

10W 100PSI

Production

monitored

fety

tes

ted

PRODUCTSERVICE

NRTL

SUD

Item # 98666

24V

CorporationContact Locations

ForNorth America:

Henkel Corporation

One Henkel Way

RockyHill, CT 06067

ForOther WorldwideLocations:

HenkelAG& Co. KGaA

Site Munich

Gutenbergstr. 3

85748Garching

Label # 890057 7

Germany

3 Technical Data

Size 152mm X 165mm X

178mm

(6” X 6.5” X 7.0”)

Max.

Relative

Humidity

80% for temperature up to

31˚C (87.8˚F) Decreasing

linearly to 50% relative

humility at 40˚C (104˚F)

Wei

ht 1.2 k

(

2.6lbs

)

Air Out

ut 0-100

(

0-6.9 bars

)

Minimum

Dispense

Time 0.020 Seconds Maximum

Dispense

Time 60.000 seconds

Input Voltage 24VDC Vacuum 406mm (16”) of Hg

Rated Power 10W Timer 0.020 – 60.000 seconds

Air Input 100 psi (6.9 bars) Max. Cycle Mode Timed, Incremental, Manual

Pollution

Degree II Timing

Repeat

Tolerance +/- 0.001%

Installation

Category I Cycle Rate 600 cycles/min

Indoor Use Altitude up to 2,000m

(6,562ft) LCD 16 X 2 display segments

Operating

Temperature 0˚C to 50˚C (32˚F to

122˚F) Storage

Temperature -10˚C to 60˚C (14˚F to

140˚F)

4 Installation

Use 5 micron Filter –Regulator –Loctite 985397 or

equivalent for inlet air supply

Fig. 4.1

4.1 10ml or 30ml syringe adapter attaches to Pulsed Air

Outlet (7) and syringe barrel.

Items Description

1 To Air Source

2 Air Filter –sold

separately

3 Power Adapter

4 Foot Switch

5 Syringe Adapter

5 Operation

5.1 Set up Instructions – Manual Dispense Cycle Setting

The Manual Mode allows the unit to pulse for the duration

that the foot switch is depressed. It is typically used to start up and

purging through a dispense needle.

The unit is factory pre-set with a dispense time of 0.1

seconds. Manual mode will not function unless there is time set

in the time display. (00.000 time setting will not allow the unit to

dispense in manual mode)

5.1.1 Turn on the unit by pressing the Power button (1).

5.1.2 Press the Mode button (2) until Manual Mode appears

on the display.

5.1.3 Turn up the air pressure by rotating the Air Pressure

Regulator knob (6) until the desired pressure is indicated on

the Air Pressure Gauge (5).

5.1.4 After filling the barrel or using pre-packaged adhesive,

attach the syringe to the syringe adapter. Make certain that

the syringe locks into place.

5.1.5 Connect the plug end of the receiver head assembly to

the Air Dispense Outlet (7).

5.1.6 If vacuum “suck back” is needed, rotate the Vacuum

Regulator (8) counter clockwise until the desired vacuum

pressure is obtained.

5.1.7 Press and hold the Footswitch to activate the dispense

cycle. (The Manual Mode is now activated)

5.2 Dispense Cycle Setting – See Figure 5.1

Push the Mode button (2) to select Timed Mode or

Incremental Mode.

Timed Mode: Allows the unit to dispense for the

the complete amount of time set on the timer

when the foot switch is initiated

Incremental Mode: Allows the unit to dispense

for as long as the foot pedal is depressed and will

continue till the set time is reached. This allows a

pre-determined amount of product to be

incrementally added in steps if desired.

5.2.1 Setting the Timer in the Timed Mode

5.2.1.1 From the Timed Mode , press and hold button the

Set button (3) for 2 seconds. The unit will enter

the Set- up Mode and allow each or the time

digits to be set.

5.2.1.2 Pressing the Set button (3) from this point moves

the the cursor to the next digit and back till the

desired time has been set

5.2.1.3 Press the (+) and (-) button to set the time for

each digit desired. (You can not go past 0 with

either button.) Minimum dispense time is 00.020

seconds

5.2.1.4 When your desired time has been entered, press

and hold the Set button (3) for two seconds to

save the data.

5.2.2 Setting the Timer in the Incremental Mode

Setting the timer from the Incremental mode, “Teach

Mode” is helpful in determining dispense time

required when dispense output is unknown. The timer

will continue to accumulate time as long as the foot

pedal is depressed, allowing the user to “teach” the

unit the exact time needed

5.2.2.1 From the Incremental Mode, press and hold the

Set button (3) to enter the “Teach Mode”. The

unit will still read Set-up, however the time will

show “0.000” in the LCD.

5.2.2.2 Press and hold down the foot switch. Product

will dispense and time will accumulate. Continue

to release and press the foot switch till the desired

quantity has been dispensed.

5.2.2.3 Press and hold the Set button (3) for two seconds

to save the data.

5.2.2.4 Press the Mode button (2) to switch the Timed or

Incremental Mode as desired. The dispenser is

now ready to dispense this new time cycle

5.2.3 Resetting the Cycle Counter

The cycle counter records the numbers of automatic

dispense cycles being activated. Up to 65,535 cycles

can be recorded. This number is shown at the lower

right hand corner of the LCD. To reset the counter;

5.2.3.1 Press and hold the Set button (3) for two seconds

to enter the Set up mode.

5.2.3.2 Then re-press and hold the Set button (3) for three

to five more seconds to reset the counter. After

two seconds the screen will first show “Saving

Data” but continue holding till the cycle counter

resets to 00000 .

Fig 5.1

Setup

TIMED MODE

P1 2.250 00004

SETUP MODE

P1 00004

SETUP MODE

P1 00004

Save and Exit...

SETUP MODE

P1 00004

SETUP MODE

P1 00004

SETUP MODE

P1 00004

SETUP MODE

P1 00004

SETUP MODE

P1 00004

SETUP MODE

P1 00004

TIMED MODE

P1 2.251 00004

TIMED MODE

P1 2.251 00000

2.25022.25022.250

22.250

22.251

22.250

22.251

Save and Exit...

22.251

TIME SETTING

COUNTER RESET

Time setting

in TIMED mode

:Press and hold for approximately 4 seconds then release

Normal Operation

Power ON/OFF

2.250

TIMED MODE

P1 00004

SET

Counter

POWER

Prog

MODE

Time

MODE

OFF

:Press then release

Change Mode

*************************

MANUAL MODE

:Press and hold for approximately 2 seconds then release

2.250

INCREMENTAL MODE

2.250

TIMED MODE

00004

6 Troubleshooting

PROBLEM POSSIBLE CAUSE CORRECTION

LCD does not

light



No power input



Check power cord

connections

Turn on power

System will not

actuate



Foot switch not

plugged in or

improperly plugged

Defective foot switch

Broken wire or loose

connection inside

unit

Defective solenoid

Defective PC board



Check foot switch

connection

Foot switch needs to be

repaired or replaced

Unplug power cord and

disconnect air supply.

Remove cover and check

for broken wires or loose

connections

Replace solenoid

Replace PC board

System will not

pressurize



Insufficient air

pressure

Air hoses not

plugged in

Regulator defective



Increase air supply

pressure

Check connection

Replace regulator

System will not

pull vacuum



Vacuum setting is

too low

Defective solenoid

Defective vacuum

venturi

Defective vacuum

needle valve



Increase vacuum setting

Replace solenoid valve

Replace venturi

Replace needle valve

Inconsistent

dispensing



Air bubbles in

adhesive

Dispense time is too

low

Dispense needle

started to clog



Reduce vacuum setting

Increase dispensing time

Replace needle

Table des matières

Langues :

Autres manuels Loctite Distributeur

Loctite

Loctite MM31 Manuel utilisateur

Loctite

Loctite 1390322 Manuel utilisateur

Loctite

Loctite 97006 Manuel utilisateur

Loctite

Loctite EQ PU20 Manuel utilisateur

Loctite

Loctite 97008 Manuel utilisateur

Loctite

Loctite 985246 Manuel utilisateur

Loctite

Loctite 97006 Manuel utilisateur

Loctite

Loctite HD10 Manuel utilisateur

Loctite

Loctite PULSE EQ RC50 Manuel utilisateur

Loctite

Loctite 97105 Manuel utilisateur

Loctite

Loctite 983437 Mode d’emploi

Loctite

Loctite LOCTITE 97504 Manuel utilisateur

Loctite

Loctite 98050 Manuel utilisateur

Loctite

Loctite SD10 Manuel utilisateur

Loctite

Loctite Universal FixMaster 1372751 Manuel utilisateur

Loctite

Loctite VoluDrop UV 97650 Manuel utilisateur

Loctite

Loctite 97115 Manuel utilisateur

Manuels Distributeur populaires d'autres marques

Silver King

Silver King Majestic SK12MAJ Guide de démarrage rapide

Franke

Franke F3Dn Twin Manuel utilisateur

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Manuel utilisateur

DAN DRYER

DAN DRYER 282 Manuel utilisateur

Essity

Essity Tork 473208 Manuel utilisateur

CBS

CBS SD300BU-88 Guide de configuration

Sealey

Sealey MK77 Manuel utilisateur

Fluid Management

Fluid Management Accutinter 1600 Manuel utilisateur

Franke

Franke DVS SD99-010 Manuel utilisateur

Graco

Graco Dispensit 1053-10C Guide de dépannage

ITALTINTO

ITALTINTO i50 Manuel utilisateur

Coca-Cola

Coca-Cola FREESTYLE 9000 Manuel utilisateur

Graco

Graco ProMix 2KE Mode d’emploi

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 Manuel utilisateur

Wayne

Wayne GLOBAL VISTA CNG Manuel utilisateur

clarsen

clarsen H133 Manuel utilisateur

PicoBrew

PicoBrew Zymatic Manuel utilisateur

BOWMAN

BOWMAN BP-007 Manuel utilisateur