LMI Technologies GoMax NX Manuel utilisateur
Quick Start Guide
15266-01.02_MANUAL_Quickstart_GoMax_NX
GoMax NX
Smart Vision Accelerator
2
Getting Started with the GoMax NX
Congratulations on purchasing GoMax NX Smart Vision Accelerator. This Quick Start Guide
provides you with the resources to get you started.
Customer Support
If you have any installation issues, please contact:
AMERICAS
LMI Technologies (Head Oce)
Burnaby, Canada
+1 604 636 1011
EMEAR
LMI Technologies GmbH
Berlin, Germany
+49 (0)3328 9360 0
ASIA PACIFIC
LMI (Shanghai) Trading Co., Ltd.
Shanghai, China
+86 21 5441 0711
LMI Technologies has sales oces and distributors worldwide. All contact information is listed at
lmi3D.com/contact.
3
Hardware Included with GoMax NX
Number Description
1 GoMax NX unit
2Power supply, cord (plug depends on part number of the kit), and Phoenix
connectors
3 DIN rail clip plate
4 DIN rail clip
5 Wall mount brackets (x2)
6 Screws (x7, not shown)
Before connecting the GoMax NX unit to a sensor system, follow the instructions in “Connecting
Power” and “Setting the IP Address”.
When you receive your GoMax NX unit, check that all components are included:
1
2
3
4
5
4
Connecting Power
To connect the power, do the following.
WARNING: Use only the provided power supply with the GoMax NX unit. Using a higher voltage
power supply will damage the unit.
1. Connect the power supply connector to the unit.
2. Plug the power adapter into an available electrical outlet.
5
3. Press the power button.
The power button LED indicator lights.
6
Setting the IP Address
Each GoMax NX unit and Gocator sensor on the sensor system network must have a unique IP
address. By default, the IPaddresses of the GoMax NX rightmost Ethernet port is set to 192.168.1.6.
To set the IP address of a GoMax NX unit, do the following:
1. Using an Ethernet cable, connect a computer to the ETH1 port on the GoMax NX unit.
2. On the computer, launch an Internet browser and navigate to 192.168.1.6.
The GoMax NX web interface is displayed.
7
3. In the Manage panel, click the Networking category.
The Networking category settings are displayed.
4. Under Interface 1, set the IP address and click Save.
The GoMax NX unit power cycles after you confirm you want to change any IP addresses.
Changing network settings disconnects the GoMax unit and stops the acceleration of any
accelerated sensors.
After the GoMax NX unit restarts, its IP addresses are changed.
5. Disconnect the laptop from the GoMax NX unit.
8
Mounting GoMax NX
LMI provides a DIN rail clip plate, a DIN rail clip, and M3 screws to mount GoMax NX on a DIN
rail. The plate allows multiple orientations of the unit using dierent sets of standos. Attach the
DIN rail clip plate to the back of the unit, and attach the DIN rail clip to the plate in the required
orientation.
BACKPLATE
4X M3 PHILLIPS SCREWS
DIN MOUNT
3X M3 PHILLIPS SCREWS
9
LMI also provides wall mount brackets to mount the GoMax NX unit directly on a wall or to a
frame. To use the wall mount brackets, remove the DIN rail clip plate from the back of the unit, and
attach the wall mount brackets to the back of the unit using the provided screws. Make sure that
the unit is securely fastened to the wall.
4X M3 PHILLIPS SCREWS
WALL MOUNT BRACKET
10
Connecting to a Sensor System
You must connect the GoMax NX unit to a sensor system through the Gigabit switch the sensor
is connected to. Connect the unit to the switch using an Ethernet cable and the ETH1 port on the
unit.
NOTE: Before connecting GoMax NX to a sensor system, make sure that it has a unique IP address
(see “Setting the IP Address” on page 6).
Autres manuels pour GoMax NX
1
Table des matières
Autres manuels LMI Technologies Carte vidéo
Manuels Carte vidéo populaires d'autres marques
Gainward
Gainward GeForce GTX 690 4GB Manuel utilisateur
ATI Technologies
ATI Technologies RADEON 137-40225-20 Manuel utilisateur
MSI
MSI N220GT series Manuel utilisateur
ATI Technologies
ATI Technologies RADEON 7000 MAC EDITION Manuel utilisateur
SIIG
SIIG aurora Manuel utilisateur
ClearSpeed
ClearSpeed ClearSpeed Advance e720 Manuel utilisateur
