LK LI-IL150 Manuel utilisateur
Thank you for purchasing product of LK Lab Korea co.,Ltd.
This User Guide describes your product’s function,
operation and safe use.
Please read carefully and keep them in mind before you operate
products.
In case some parts which need extra care for users,
we put some mark as below for the occasion.
[Warning Mark]
This is mark for Dangerous Situation.
If users ignore this, it might cause of serious personal
injury or damage for products.
[Attention Mark]
This is mark come up with the situation which needs
extra care.
When users recognize this sign, they have to operate more
carefully.
3
[ Contents ]
1. Preparation
1.1 Introduction
1.2 Feature
1.3 Structure
1.4 Installation
2. Operation
2.1 Naming and Function of Temperature Controller
2.2 FIX MODE (One Temp. Operation)
2.3 Program MODE (Multiple Temp. Operation)
2.4 Additional Function
3. Maintain
3.1 Maintaining after Use
3.2 Disorders and Solutions
3.3 After Sales Service
4. Specification
5
5
5
6
9
10
10
12
14
17
18
18
18
20
21
4
1. Preparation
This product is used for bacterial culture and then cultured tissue
culture experiments of various flora and fauna. It is also useful in various
experiments such as thermo plant specimen storage and storage
experiments, such as environmental change experiments.
We consider the convenience and safety of the users through a variety of
functions and a maximum of safety.
1. Preparation
Instruction
1.1
1.2.1▶ Function and Convenience
- Heat Flow Circulation method, provide to equivalent temperature
distribution inside chamber.
- 5 steps of Flow Control prevent spreading of samples inside.
- You can observe the internal conveniently through the Glass Door.
- Graphic LCD Display provide handy operation and control.
- Program designed to control at multiple temperature.
(10 step control available)
- PID control system with high performance microprocessor provide
quick and precision temp. control.
- By Auto Tuning installed provide automatic calculation of PID value
based on test environment.
- The experimental data can be freely transferred to a PC via the
RS485 port.
1.2.2▶ Safety
- Double over heated safety device installed.
(1st Controller Alarm, 2nd Forced Shut Out Circuit)
- No running of Heater and Fan during door open.
- With appearance of disorder, alarm activated with buzzer and
message displaying.
Feature
1.2
5
1. Preparation
Structure
1.3
[Low Temp. Incubator / B.O.D Incubator ]
6
1.3▶ continued.. ▶ ▶
4
3
9
2
6
1
7
8
5
10 11 12 13
14
[1] Over Temp. Limiter
[2] Temperature Controller
[3] Door
[4] Door Handle
[5] Glass Door
[6] Shelf rail
[7] Shelf
[8] Door Packing
[9] Chamber
[10] Power Swtich
[11] Communication Port
[12] Circuit Breaker
[13] Power Cord
[14] Lower Cover
1. Preparation
[1] Over Temp. Limiter
the temperature go over the set temperature, shut out the power of
heater immediately to prevent overheat, user need to set 10% higher
temperature from actual treat.
[2] Temperature Controller
use for controlling temperature inside.
[3] Door
insulation between inside and outside of chamber, prevent overheated
of surface.
[4] Door Handle
handle to open and close the door.
[5] Glass Door
observe the internal through the Glass Door.
[6] Shelf rail
used for fixing shelf, adjustable of height of shelf.
[7] Shelf
2 type as wire and perforated, used for put on the sample inside chamber.
[8] Door Packing
Silicone packing resistant seal the chamber.
[9] Chamber
space for treat made with stainless.
[10] Power Swtich
on/off switch for main power.
7
1. Preparation
[11] Communication Port
RS485 communication port.
[12] Circuit Breaker
Breaker of overcurrent.
[13] Power Cord
supply electronic power to equipment.
[14] Lower Cover
Lower part on the cover there are condenser inside.
8
1. Preparation
1.4.3▶ Connecting of Power
1) Set power switch OFF
2) In case the power cord is separated from main body, connect them
first and plug the cord to power supply point(outlet)
/ Before you plug to supply electronic power, please carefully
check for electrical specification of equipment and considering
the specification.
/ Must use power supply point that completely ground connected.
/ Do not touch the power cord with wet hand.
Installation
1.4
1.4.1▶ Contents of product(with delivery)
1.4.2▶ Installation Environment
- Avoid direct light.
- Place where with less vibration and flat surface.
- Maintain the temperature of surrounding area the product placed
between 5 to 40℃.
- Maintain the humidity of surrounding area the product placed below
RH 80%.
- Avoid the place where may occur flammable gas.
- Avoid the place where may occur noise and high frequency.
- Avoid the place where may occur overcurrent or water leak.
- Avoid the place where may occur corrosive gas or dust.
- Do not put the substance in an organic solvent and or explosive.
- Please drop back from the sides by 20cm at least when installing
the unit.
Main Body(1set), Power Cord(1ea), Wire Shelf(2ea),
Shelf Rail(4ea), User Guide(1copy)
/ Must place where temprature beween 5 to 40℃ and
humidity under 80%
9
2. Operation
2. Operation
Naming and Function of Temperature Controller
2.1
[1] Graphic LCD
Available to check status of the equipment and display data.
[2] Run Lamp
Light on during the equipment operates.
[3] Heater Lamp
Display quantity of output with flickering.
[4] Timer Lamp
Light on during operate with timer.
[5] A.T Lamp
Light on during operate with auto tuning.
[6] UP key
Use for increasing of set value and set of Fix Mode.
[7] Down key
Use for decreasing of set value and set of Program Mode.
10
1
2345
10
6
9
7
8
11
13
17
12
15
14
16
[8] Shift key
Use for moving the position of set value and set of Auto-Tuning Mode.
[9] Run/Stop key
Use for operating, stop and set values.
[10] Mode key
Use for changing menu.
[11] Display Mode
User can select one between FIX(one temp.) and
Program(multiple temp.) Mode.
[12] Message Displaying Window
Display of the message related status of the product.
[13] PV Display
Display current temperature of equipment.
[14] SV Display
Display target temperature the user set.
[15] Timer Display
Timer display remain time for operation “--.--.--“ means timer off.
[16] Fan Speed Display
Display Step of inner circulating fan(available to set 0 to 5).
[17] RUN/STOP Display
Display the status RUN or STOP.
2. Operation
11
Ce manuel convient aux modèles suivants
3
Table des matières
