Livoo DOM343 Manuel utilisateur
Instruction Manual
WWW.LIVOO.FR
Reference: DOM343
Version : 1.4
Language: English
Sewing machine
Instruction Manual
1
You have urchased a roduct LIVOO brand and we thank you. We take great care in design, ergonomics
and ease of use of our roducts. We ho e that this roduct will give you com lete satisfaction.
This instruction manual is available too on our website www.livoo.fr
SAFETY ADVICES
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE
APPLIANCE AND SAVE IT FOR ANY FURTHER NEED.
Incorrect o eration or usage is likely to cause damage to the
a liance and injure the user. Make sure that you follow all safety
instructions. Only use this a liance for the ur ose for which
has been designed; we decline all res onsibility in the event of
damage due to incorrect use or bad handing.
1. Read all instructions before use this a liance.
2. Before use check that the voltage of your wall outlet
corres ond to the rated voltage manner.
3. Check that your main voltage corres onds to that stated on
the a liance.
4. The safety instructions do not by themselves eliminate any
danger com letely and ro er accident revention measures
must always be used.
5. This a liance can be used by children aged from 8 years and
above and ersons with reduced hysical, sensory or mental
ca abilities, or lack of ex erience and knowledge if they have
been given su ervision or instruction concerning use of the
a liance in a safe way and understand the hazards involved.
Instruction Manual
2
6. Children shall not lay with the a liance.
7. Cleaning and user maintenance shall not be made by children
without su ervision.
8. If the su ly cord is damaged, it must be re laced by the
manufacturer, its service agent or similarly qualified ersons
in order to avoid a hazard (*).
9. Un lug the a liance before carrying out maintenance or
re lacing lam s.
10. Switch off or un lug the a liance when leaving it
unattended.
11. The a liance is only to be used with the ower su ly unit
rovided.
12. Do not o erate the machines that damaged or drowned, or
with ower line or lugs damaged, or unable to run
com letely.
13. Do not o erate the machine in unventilated environment.
Kee ventilate and be sure no lint, dust and scattered textures
accumulated near the foot controller.
14. Do not use the machine outdoors.
15. Kee fingers far from running com onents, es ecially the
sewing needle.
16. Turn “OFF” the ower lug during sewing machine
adjustment like resser foot ty e change, adjust needle
distance adjustment, bobbin change, etc.
17. This a liance is intended to be used in household and
similar a lications such as:
Instruction Manual
3
•staff kitchen areas in sho s, offices and other
working environments
•farm houses
•by clients in hotels, motels and other
residential ty e environments
•bed and breakfast ty e environments
TECHNICAL SPECIFICATION
Sewing machine:
Rated voltage: 6V
Rated current: 1500mA
Adapter:
Rated in ut: 100-240V~ 50-60Hz 0.4A
Rated out ut: 6.0VDC 1.5A, 9.0W
Information published Value and precision
Unit
DELTA
BP61071
67452 Mundolsheim – France
- -
Model identifier DOM343 -
Input voltage
100-240
V
Input AC frequency
50-60
Hz
Output voltage
6.0
VDC
Output current 1.5 A
Output power 9.0 W
Average active efficiency 82.8 %
Efficiency at low load (10 %) 76.3 %
No-load power consumption 0.07 W
Instruction Manual
4
DESCRIPTION AND ACCESSORIES
1
1. Reverse button
2. Pattern selector button
3. Thread take-u lever
4. Œillet de guidage du fil
Winding thread guide
5. Guide fil thread guide
6.
7. Threading guiding s ring
8. Thread tension adjustment
wheel
9. Thread tension release bar
10. Thread cutter
11. Needle clam screw
12. Presser foot
13. Bobbin location with
trans arent cover
14. S ool in
15. Hand wheel
16. ON/OFF Switch
17. Power/foot switch socket
10
9
8
7
6
5
4
3
2
14
12
11
13
15
16
Instruction Manual
5
BEFORE FIRST USE
Remove all ackaging of the device.
Check if the voltage of the a liance corres onds to the main voltage of your home.
Connect to the power source
Plug the ada ter into the sewing machine (right connector), and lug into an AC outlet.
17. Ada ter
18. Foot switch
19. Bobbins
20. Needles
21. Button hole foot
22. Sewing late
23. Zi er foot
24. Seam ri er
25. Threader
26. Double needle
18
19
17
20
21
22
23
25
24
26
Instruction Manual
6
Connect the foot switch on the sewing machine (left connector).
Press the on/off switch to “ON” for ower.
INSERT OR CHANGE THE NEEDLE
Attention: Turn ower to “off” osition before inserting the needle, to avoid electrical shock! Change the needle
regularly, es ecially if it is showing signs of wear and causing roblems.
Follows these ste s:
Turn off the sewing machine.
Turn the hand wheel (12) to to osition.
Loosen the needle clam screw and tighten again after inserting the needle.
The flat side of the shaft should be towards the back.
Insert the needle as far u as it will go.
Instruction Manual
7
Flat art of the sewing needing shall be installed backward
Attention：Pay attention to the following oints during sewing needle installation
Make sure the erfect quality of the sewing needle. The sewing needles shown in the right Fig will cause roblems:
A. curved needles
B. blunt needles
C. needle with damaged in oint
THREADING
Insert the S ool Pin at the rear of the machine and ut the bobbin on it (1).Pass the thread of the bobbin through the
hole of winding slice from back to front (2) and through the thread guide then, ull the thread over the right side of
the thread tension adjustment wheel (3). Follow the arrow (5) with the thread and make u the through the
lever (6).
Take down the thread in the threading guiding s ring from the front to the back (7) and let it ass in the guide located
at the to of the needle (8).
Threading to the inhole of the sewing needle (9).
Instruction Manual
8
(5) (6) (7) (8)
You can hel yourself to the needle threader included with this roduct.
Pass the metal loo through the needle hole. Move your thread inside and bring out the needle (see schema below).
INSTALLATION AND EXTRACTION OF THE BOBBIN THREAD
Before installing the bobbin, be sure that the machine is switched off in order to avoid injuries.
Please follow carefully the following ste s:
Lift the resser foot with the lifter and raise the needle with the hand wheel and make sure to leave a 10 cm tail of
thread already mounted on the needle (1).
Instruction Manual
9
Remove the trans arent cover (2)
Place the bobbin into the slot, so that so that the thread round in a clockwise direction (3) (4).
Leave 10 cm tail of thread (5).
Here is a schema:
Hold the u er thread with the left hand. Turn the handwheel (6) towards you (counterclockwise) lowering, then
raising needle.
Gently ull on the u er thread to bring the bobbin thread u through the needle late hole (7).
Lay both threads to the back under the resser foot (8).
Put on the trans arent cover after the bobbin thread and u er thread ressed under the resser foot (9).
(1) (2) (3) (4)
Table des matières
