Lithonia Lighting EU2C Manuel utilisateur

DO NOT PRINT with INSTRUCTIONS

Information below is for LITHONIAdocumentation purposes only.

DO NOT include this page in the printing of this instruction sheet.

PART NUMBER: EMCSA00911

DESCRIPTION: INSTRUCTION SHEET, EU2C

SPECIFICATIONS: Prints 8.5 x 11, portrait. Two side, one color: BLACK ink.

PAGINATION: 8.5” X 11 portrait.

CONFIGURATIONS

PART # INSTRUCT SHEET DESCRIPTION REV DATE STANDARD UNIT

EU2C B09.12.2018 X

EMCSA00795 ABLLED WARNING X

DATE CHANGE DESCRIPTION BY

One Lithonia Way, Conyers GA30012

Phone: 800-334-8694

www.lithonia.com

PAGE: 0 of 4

RRB

9.12.18REV. B: Removed SD HO wiring diagram - ABL not offering SD and hO together at this time.

REQUIRED INSTRUCTION SHEETS for EU2C models

EMCSA00912

EMCSA00911

A08.06.2018

SDT

SD INSTRUCTIONS

RRM

8.06.18REV. A: Initial Release

INSTALLATION INSTRUCTIONS for Lithonia Lighting EU2C Models

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

LED DUAL HEAD EMERGENCY LIGHTING FIXTURE

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

WARNING:

FAILURE TO FOLLOW THESE INSTRUCTIONS

AND WARNINGS MAY RESULTIN DEATH, SERIOUS INJURYOR

SIGNIFICANT PROPERTY DAMAGE. For your protection, read and

follow these warnings and instructions carefully before installing or

maintaining this equipment. These instructions do not attempt to cover

all installation and maintenance situations. If you do not understand

these instructions or additional information is required, contact

LITHONIALIGHTING or your local LITHONIALIGHTING distributor.

WARNING: RISK OF ELECTRIC SHOCK - NEVER CONNECT

TO, DISCONNECTFROM, OR SERVICE WHILE EQUIPMENTIS

ENERGIZED.

WARNING: RISK OF FIRE. Lamps are hot. Keep combustible material away from hot parts. Observe lamp manufacturer’s warnings,

recommendations and restrictions on lamp operation and maintenance. Make sure lamps are correctly installed.

CAUTION: The battery in this unit may not be fully charged.After electricity is connected to unit, let battery charge for at least 24

hours, then normal operation of this unit should take effect.To check, press the TEST button.The lamps on the unit should turn on.

IMPORTANT SAFEGUARDS: When using electrical equipment, basic safety precautions should

always be followed, including the following:

PAGE: 1 of 4

Fig.A (J-Box) Fig.B Fig.C

BATTERY CONNECTOR

PLUG IN

NOTE:Complies with California Title 20. Product label is marked with .

INSTALLATION:

NOTE: Max mounting height is 10 ft to achieve at least 1 ft-candle of illuminance in emergency mode.

• Do not use outdoors.

• Consult local building code for approved wiring and installation.

• DisconnectAC power before servicing and installation.

• Do not mount near gas or electric heaters.

• Do not use this equipment for anything other than its intended use.

•

Theuse of accessoryequipmentnotrecommendedby the manufacturer will voidproductlistingandwarranty and maycauseanunsafe condition.

• Any service on this equipment should be performed by qualified personnel only.

• Equipment should be mounted in locations and at heights where it will not be subject to tampering by unauthorized personnel.

•Do not ceiling mount.

• Use caution when servicing batteries.

• Cap unused wires with enclosed wire nuts or other approved method.

• Make sure wire terminations are secure and leads are properly tucked in appropriate wire channels.

INSTALLATION INSTRUCTIONS

J-BOX MOUNTING:

Feed ﬁxture leads through the back plate and connect to AC power supply (Fig A, page 1). For 120V use black and white wires

and for 277V, use red and white wires.

Attach back plate to J-Box and secure with screws.

Complete the battery connection. (Fig. B, page 1)

Align snaps and push housing directly onto the back plate (Fig. C, page 1).Apply continuousAC power.

After the battery has been left to charge for 24 hours, test the unit by pushing the test switch and the LED lamp head will turn ON.

CONDUIT MOUNTING:

1. Secure back plate to wall surface using keyhole knockouts on the back plate.

2. Route wires through hole in conduit flange and make conduit connection. For 120V use black and white wires and for 277V, use

red and white wires.

3. Complete the battery connection (Fig. B, page 1).

4. Align snaps and push housing directly onto the back plate. Apply continuous AC power.

5. After battery has been left to charge for 24 hours, test the unit by pushing the test switch and the LED lamp head will turn ON.

WALLMOUNTING:

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE:2of 4

1. Secure back plate to wall surface using keyhole knockouts on the back plate.

2. Feed fixture leads through back plate and connect to AC power supply. For 120V use black and white wires and for 277V, use

red and white wires.

3. Complete the battery connection (Fig. B, page 1).

4. Align snaps and push housing directly onto the back plate. Apply continuous AC power.

5. After battery has been left to charge for 24 hours, test the unit by pushing the test switch and the LED lamp head will turn ON.

OPERATION:

1. During an electrical power failure, the LED lamps will automatically come on for a minimum of 90 minutes.

2. To test, press the "TEST" switch. The emergency LED lamps will illuminate and LED indicator will turn OFF. When the switch

is released, the lamps will turn OFF and the LED indicator will turn ON.

LED STATUS INDICATOR KEY and TROUBLESHOOTING:

Visual Status Indicaon Troubleshoong/Acons to Take

RED

GREEN

UNLIT

1. Baery connecon is not made.

2. Baery has been diagnosed as dead or defecve aer 24

hours of connuous charging with AC power supplied.

Baery is connected, AC power has been supplied and xture is in

charging state.

AC power has not been supplied.

1. Make connecon; or if baery is connected, disconnect

battery for eight seconds and then reconnect.

2. Replace the battery.

This is the normal state. No acon required.

Supply AC power.

TESTING:

National Electric Code (NEC) and NFPA101regulations require that routine tests need to be performed as listed below: Once every

month, the unit needs to be tested for duration of 30 seconds. Push in and hold the test switch to perform this test. Once every 12

months, a full 90 minute (per UL requirements) test needs to be performed on the unit. Disconnect power to the unit and leave it in

the emergency mode. The lamps should stay ON for at least 90 minutes. Written records of the testing are to be kept for

examination by the authority having jurisdiction.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

WIRING DIAGRAMS

REMOTE CAPABLE

BLUE(-)

YELLOW(+)

BLUE(-)

YELLOW(+)

LAMP

YELLOW(+)

LAMP

READY

TEST

BATTERY

BLACK

Note:

Unused input lead must

be properly insulated with

wire nut or other approved

method.

RED

BLACK

WHITE

277V

120V

CHARGER

BOARD

LAMP

READY

TEST

BATTERY

RED

BLACK

RED

BLACK

WHITE

277V

120V

LAMP

YELLOW(+)

BLUE(-)

YELLOW(+)

BLUE(-)

CHARGER

BOARD

AC INPUT CONNECTOR

(MOUNTING PLATE)

AC INPUT CONNECTOR

(MOUNTING PLATE)

TO REMOTE

Note for HO models:

Use 18-22 AWG stranded

wire to connect remote lamp

heads.

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE:3 of4

Condition - Emergency lights are dim

1. Battery not fully charged.Allow battery to recharge for 24 hours and then retest. If lights are still dim, replace battery.

TROUBLESHOOTING:

Condition - The emergency lights do not operate

1. If the charge indicator light is OFF: Check that the circuit breaker forAC supply is ON.

2. If the charge indicator light is ON: Check that battery is properly connected. If problem persists, Replace battery. If remote lamps (where appli-

cable) are connected to the equipment, then turn OFF theAC supply and disconnect the remote circuit wires from the equipment. Turn ON the

AC supply and depress the test switch. If the local lamps (mounted on the equipment itself) come ON, then check the remote circuit for short or

overload condition and correct as required. Reconnect the circuit wires and restoreAC power. If the local lamps don’t turn ON after disconnecting

the remote circuit wires, then replace battery.

INSTALLATION INSTRUCTIONS

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

PAGE: 4of 4

One Lithonia Way, Conyers GA30012

Phone: 800-334-8694

www.lithonia.com Part No. EMCSA00911, REV B

2018.09.12

AC INPUT CONNECTOR

(MOUNTING PLATE)

LAMP

READY

TEST BATTERY

RED

BLACK

WHITE

YELLOW(+)

BLUE(-)

WHITE

YELLOW(+)

BLUE(-)

LAMP

RED

BLACK

WHITE

277V

120V

CHARGER

BOARD

Table des matières

Autres manuels Lithonia Lighting Équipement d'éclairage

Lithonia Lighting

Lithonia Lighting DSX0 Manuel utilisateur

Lithonia Lighting

Lithonia Lighting WST LED Manuel utilisateur

Lithonia Lighting

Lithonia Lighting PreCise ELA LCRIS Series Manuel utilisateur

Lithonia Lighting

Lithonia Lighting ELU 4 Manuel utilisateur

Lithonia Lighting

Lithonia Lighting EDGR Manuel utilisateur

Lithonia Lighting

Lithonia Lighting EXTREME LVS2 120/277 ELN SD Series Manuel du propriétaire

Lithonia Lighting

Lithonia Lighting KVF Series Manuel utilisateur

Lithonia Lighting

Lithonia Lighting OFL2WG Manuel utilisateur

Lithonia Lighting

Lithonia Lighting Affinity Instructions d'installation

Lithonia Lighting

Lithonia Lighting LHXNY Manuel utilisateur

Lithonia Lighting

Lithonia Lighting ECBG LED M6 Manuel utilisateur

Lithonia Lighting

Lithonia Lighting TFR Series Manuel utilisateur

Lithonia Lighting

Lithonia Lighting JCBL Series Manuel utilisateur

Lithonia Lighting

Lithonia Lighting WPX1 LED Manuel utilisateur

Lithonia Lighting

Lithonia Lighting LZ Series Manuel utilisateur

Lithonia Lighting

Lithonia Lighting CUC8 Manuel utilisateur

Lithonia Lighting

Lithonia Lighting CPRB 18LM MVOLT Manuel utilisateur

Lithonia Lighting

Lithonia Lighting TWA Manuel utilisateur

Lithonia Lighting

Lithonia Lighting KBA Manuel utilisateur

Lithonia Lighting

Lithonia Lighting LEM04 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur