LISTAESCAN ARLINK 8000 Instructions de montage

Arlink 8000 Workstation

Instructions for Assembly

Introduction

Basic Frame Assembly

Worksurface Assembly

Drawer and Light Fixture Assembly

Micro Slot Accessory Mounting

Macro Slot Accessory Mounting

Worksurface Grounding Instructions

Wrist Strap Receptacle Grounding & Cleaning

Making Workspace Work® is a trademark of Lista International Corporation.

Creation Date Document Number Rev Description

Feb/01/06 AS80026 B Arlink 8000 Workstation

This manual is proprietary information of Lista International Corporation. Unauthorized

reproduction of any portion of the manual is prohibited without consent of Lista

International Corporation. The material in this manual is for informational purposes

only. It is subject to change without notice. Lista International Corporation assumes

no responsibility for any typographical errors contained in the manual.

106 Lowland Street

Holliston, MA 01746-2094

E-mail: sales@ listaintl.com

For questions or technical support, call 1-800-722-3020

ISO 9001 Certified

Table of Contents

Arlink 8000 Introduction..............3

Basic Frame................................4

Single Station..............................4

In-Line Station.............................4

Alignment....................................4

Standard Worksurface................5

Round or Straight Back Corner...5

Square Corner............................5

Rear Corner Support Leg ...........5

Drawer, Tote Box &

CPU Holder.................................6

Upright Trim................................6

Parabolic.....................................6

Fluorescent Fixture.....................6

Light Trim....................................6

Tool Trolley Track........................7

Micro Slot Accessories................7

Modesty Panel............................7

Powerbeam.................................7

Parts Bin Rail..............................7

Part Bin Rail Accessories............7

Airbeam.......................................8

Steel Shelf...................................8

Open Wire Shelf..........................8

Swing Arm System......................8

Grounding Static Protected

Worksurfaces..............................9

Common Point Ground Block .....9

SC12 Dual Wrist

Strap Receptacle.........................10

Laminate Cleaning......................10

Arlink 8000

Assembly Instructions

In order to appreciate this unique concept, we suggest you spend a

few minutes studying the instructions before starting assembly of

your Arlink 8000 Workstation.

Should you have any difficulty during assembly or have further

questions, please call Technical Support at (800) 722-3020.

1. Décor Trim

2. Vertical support column

3. Light fixture support

bracket

4. Fluorescent fixture

5. Wire shelf

6. Macro bracket

7. Power beam

8. Laminate worksurface

9. Each additional column

outrigger and stabilizer

panel creates another

station

10. Worksurface support

brackets

11. Worksurface support

beams

12. Stabilizer panel

13. Swivel footrest

14. Outrigger with

adjustable leveling glide

3 4

Single Station Assembly

Stabilizer panels are mounted between the columns

with “T” bolts. Usually these are mounted through

the second, fourth, and ninth holes from the bottom

of the columns.

The access slot in the stabilizer channel should be

positioned over the third hole from the bottom of the

column to provide access to the outrigger clevis pin

and retainer.

Mount the stabilizer using the 1/4-20 x 2” “T” bolts,

1/4” washers, and 1/4-20 wing nuts provided.

In-line Assembly

Begin by assembling all columns and outriggers.

Then assemble the first column and stabilizer in the

manner described previously. The middle column

will have two stabilizers mounted to it. Therefore you

must bolt through the column and both stabilizers.

This procedure is repeated for each successive

workstation. At the last column of your in-line

station ensure the “T” bolt is facing the stabilizer

panel. Alignment

Alignment of the system is necessary at this point.

The columns must be both vertically and horizontally

aligned. This can be accomplished by using a level,

and adjusting the glides. Floor glides must be

adjusted so that each column supports equal weight.

NOTE: Alignment should be re-checked after

accessories are installed.

Basic Frame Assembly

Install all leveling glides before starting assembly. The column glide should only be threaded half way into

the column, while the outrigger glides should be threaded into the outriggers their full length.

Install outriggers by inserting the tongues of the outrigger into the center slot or Macro slot of the column.

Secure with clevis pins through the tongues of the outrigger, then insert the retainer through the hole in the

clevis pin. Outriggers must be positioned as shown below to ensure correct alignment of the in-line system

as well as correct alignment for footrest mounting.

Worksurface Assembly

Place the worksurface face down on a smooth surface

to prevent damage. Place the worksurface brackets

and support beams in their proper locations as shown

below. Install the four 1/4-20 x 1” machines screws

provided and tighten once all are in place.

NOTE: If you have drawers on your system now is the

time to hang them. (See drawer mounting instructions).

Round Corner or Straight Back Corner

Worksurface

These worksurfaces are mounted between two 900

adjacent modules. They require one pair of

worksurface support brackets. Place the worksurface in

the desired location and fasten the support brackets

using the four 1/4”-20 x 3/4” machine screws provided

and tighten once all are in place.

Square Corner Worksurface

This worksurface assembly requires it’s own 36”

module (starter or adder) and support brackets as

shown. Two pair of worksurface support brackets are

supplied. (Only three brackets are actually required).

Place the worksurface in the desired location and fasten

the support brackets using the six 1/4”-20 x 3/4”

machine screws provided and tighten once all are in

place. Rear Corner Leg Support

This worksurface is mounted using one pair of

worksurface support brackets. Place the worksurface

on the brackets. Adjust the height of the leg relative to

the worksurface by unfastening the screw at the bottom

of the leg assembly and sliding the inner tube up or

down as required. Line up the threaded insert and

fasten. Fine adjustments can be done with the leveling

glide. Now slide the rear leg to the back corner of the

worksurface approximately 2” from either side and

fasten to the worksurface using the wood screws

provided.

Upright Trim

Mount the two trim strips provided with a starter

assembly one on each end of assembled system,

by aligning trim with top of column and pressing it

into place down the length of the column. Inside

trim should be installed after light placement (so the

power cord may be concealed between the trim

and column), but before other accessories.

Drawer, Tote Box & CPU Holder Mounting

Drawers and Tote Boxes are mounted using two steel strip drawer

hangers which slide inside the worksurface support beams.

Drawers should be installed before the worksurface assembly is

mounted on the system. If the worksurface assembly is already in

place, it should be removed for drawer installation.

The worksurface is placed face down with one worksurface support

bracket and two support beams loosely fastened to the top.

For ease of assembly the drawers can be removed by releasing the

disconnects on both sides of the slides and pulling the drawer

forward to separate the slides. Fasten the two hangers (threaded

inserts facing away from the drawer housing), loosely to the housing

using the four 1/4”-20 x 1” machine screws provided. Slide the drawer hangers into the open end of the

worksurface support beams. Install the remaining worksurface support bracket and tighten all hardware.

Parabolic

The 36” and 48” parabolics are installed using the

two cap screws provided. The 60” & 72” parabolics

are installed by first putting the end plates in place,

by inserting it into the extruded slot of the light

fixture. With both end plates in place, the parabolic

may then be installed using the two cap screws

provided.

Fluorescent Fixture

Remove the screws from the top of the light housing.

Places the brackets as shown below and replace the

screws. Mount the assembly at the desired height of

the column. Ensure the brackets are properly seated

by lifting the front edge of the light until the brackets fall

into there seated position. Route the power cord down

the inside of the column and cover with accent trim.

Light Trim

Start installing at one end of the light. The light trim

will fit snugly around the front edge of the light housing.

With one end in place, slide your hand along the length

of the trim, pushing it onto the light housing.

Modesty Panel

Modesty Panels are hooked into the micro slots at

any convenient point on the column. Install both

sides of the panel at the same time. Push the

panel down to lock it in place.

Power Beam

Power Beams are installed by hooking the brackets

into the micro slots. Hook the cord end in first then

the opposite end.

Tool Trolley Track

Mounts to light brackets, with or without light. Can

be mounted in front of or behind light. Install one of

the screws and square nuts provided. Slide tool

trolley inside the track. Install the screw and nut at

the other end of the track.

Micro Slot Accessories

Accessory Cabinet, Tool Box, Shirley Bin, Sloping

Document Shelf, to name a few, can be mounted at

any desired height along the column.

Parts Bin Rail

Parts Bin Rails accept industries standard bins and

are available in 2”, 4” and 6” depths for tiered

arrangements. Position as required in micro slots.

For large heavy bins install a second rail below for

support. Parts bin rails may be grounded by

installing a ground lead (not supplied) with a screw

through the hole in either end of the bin rail and

connect to earth ground.

Parts Bin Rail Accessories

Tool Holder, Bottle Holder, Wipes Holder, and

Solder Spool Holder. These hang anywhere along

the length of the parts bin rail.

Steel Shelf

This shelf can be mounted in the macro slots

anywhere along the height of the column on 3”

increments. The slope of the shelf is adjustable to

00, 150, or 300. The shelf may be grounded by

installing a grounding lead (not supplied) with a

screw through the hole at either end of the shelf

and connect to earth ground.

Swing Arm System

The 8420 and 8423 universal brackets are used to

support the swing arm system. The 8420 bracket

is installed at the desired height in the macro slot

of the column. To prevent the bracket from being

accidentally dislodged, a pin is provided that

should be inserted through the holes in the

embossed side of the bracket and into the column.

The 8423 bracket is installed at the desired height

on the side of the column, using the three 1/4”-20

x 1 3/8” bolts, washers and lock nuts provided.

Air Beam

Air beams are provided with two or three receptacles

for 1/4” NPT quick connects. Any receptacles not

used with quick connects must be plugged. Each

end of the air beam is equipped with a quick connect

fitting for 1/4” tube. This allows air beams to be

connected in line. You can remove or install the red

blanking plug as shown below. Either tubing or

blanking plug must be in place to prevent pressure

loss. 18” of 1/4” tube supplied.

Quick Connect Fitting

Push collar in, at the same time, pull out plug or

tubing.

Open Wire Shelf

Position macro brackets in the column at the

desired height, with the offset of the brackets

facing inwards. Mount the shelf onto the brackets

with the wire securely in the slots of the brackets.

Shelves may be installed with the lip edges facing

up or down. Be sure brackets are properly seated

in the columns before loading the shelf.

Grounding Static Protected Worksurfaces

In order to prevent a possible electrical

shock hazard to personnel, the static

protected laminate should not be directly

connected to ground at any point.

Recommended grounding procedures

suggest installing an in-line 1 MEG OHM

current limiting resistor between the static

protected laminate and the ground.

Electrical (Hydro) grounding circuits may

not be at actual ground potential. It is

recommended that a separate ground

circuit be installed for the static protected

worksurface.

If your worksurface was not supplied with a

factory drilled grounding location, use a

7/32” drill bit to drill into the worksurface in

the desired location ensuring that no

structure will obstruct the bolt. IT IS

IMPORTANT TO USE THE CORRECT

SIZE DRILL BIT TO ENSURE PROPER CONTACT WITH THE CONDUCTIVE LAYER. Install the

brass ground bolt. Lightly hammer the knurl into the worksurface until the bottom of the bolt head is

flush with the laminate. Install washer, brass nut, ground lead, and brass nut as shown. Do not over

tighten the nut, snug down firmly to ensure contact between the bolt and the laminate.

Common Point Ground Block

The purpose of a common point ground

block is to bring all required ground leads

to a common ground point. If a common

point ground block is required, it should be

mounted (using the attached adhesive

strips) on the underside of the worksurface

in a convenient place, out of the way but

accessible from both sides. Note one side

of the base is embossed with the indication

1 MEG OHM. All connections made on

the other side of the common point ground

block will be connected directly to ground.

Connect ground leads from the brass

ground bolt and the dual wrist strap

receptacle to the direct to ground side of the common point ground block. Ground leads from any

electrical equipment should also be connected to the direct to ground side. Ground leads from the

metal frame of the workstation and/or other metal accessories should be connected to the one mega

ohm side of the ground block. Ensure all ground leads are tucked away neatly to prevent accidental

disruption of ground connections.

Laminate Cleaning

The permanent static dissipative layer is embedded below a

decorative surface layer. Cleaning may be accomplished with

a damp cloth and any non-abrasive detergent cleaner without

affecting the electrical properties. Waxes should not be used

as they may impair the static dissipation.

SC12 Dual Wrist Strap Receptacle

This should be mounted onto the worksurface

support beam much like the drawer assembly.

Loosely fasten the hanger to the wrist strap

receptacle. Slide it into the worksurface support

beam and tighten hardware. Attach ground lead

to brass worksurface ground bolt. See page 7 for

worksurface grounding instructions.

Table des matières

Autres manuels LISTAESCAN Ordinateur de bureau

LISTAESCAN

LISTAESCAN ARLINK 7000 Instructions de montage

Manuels Ordinateur de bureau populaires d'autres marques

HP m9060n - Pavilion - Elite Fiche technique

Asus

Asus E210 Series Manuel utilisateur

Dell

Dell Inspiron 600m Manuel utilisateur

Dell

Dell Inspiron 3662 Manuel utilisateur

TotalFlow

TotalFlow uFLO Manuel utilisateur

HP Presario SV7000 - Desktop PC Manuel utilisateur

HP ProDesk 400 G5 Manuel

Logitech

Logitech MK320 Manuel utilisateur

Dell

Dell XPS 730 H2C Manuel utilisateur

Sony

Sony Vaio Series Manuel utilisateur

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuel utilisateur

Alto

Alto MD 250 Manuel utilisateur

Lenovo

Lenovo ThinkCentre Edge 72 Manuel

Lenovo

Lenovo ThinkStation D20 Manuel

Arbor Technology

Arbor Technology FPC-7800 Series Manuel utilisateur

Sony

Sony VAIO VGX-TP1 Series Manuel utilisateur

Asus

Asus Eee Box B204 Manuel utilisateur

Dell

Dell Optiplex 9010 All In One Manuel utilisateur