Lippert Components Solera Instructions d'installation

lippertcomponents.com 574-537-8900 Rev: 01.17 - Solera®Family and Screen Room

Solera®Family and

Screen Room

Installation and Owner’s Manual

(For Aftermarket Application)

Table of Contents

Introduction ..............................................2

Preparation ...............................................2

Resources Required.....................................2

Installation................................................3

Install Upper Brackets ...................................3

Attach the Side Panels ..................................3

Install Unit Skirting.......................................6

Securing the Room to the Ground ......................7

Removing Spikes ........................................7

Storing The Panels .......................................8

Notes ......................................................8

Solera®

Family and

Screen Room

Installation and

Owner’s Manual

(For Aftermarket Applications)

lippertcomponents.com 574-537-8900 Rev: 01.17 - Solera®Family and Screen Room

Solera®Family and

Screen Room

Installation and Owner’s Manual

(For Aftermarket Application)

Introduction

The Solera®Family Room and Screen Room are designed

for use on Solera Classic, Solera Hybrid and Solera

12V power awnings, Carefree Fiesta, Spirit, Pioneer

manual, Traveler & Eclipse 12V power awnings, Dometic

Sunchaser, 8500 manual, Weather Pro and 9100 series

12V power awnings.

Additional information about this product can be obtained

from www.lci1.com/support or by downloading the free

MyLCI app. The app is available on iTunes®for iPhone®

and iPad®and also on Google Play™for Android™users.

iTunes, iPhone and iPad are registered trademarks of

Apple Inc. Google Play and Android are trademarks of

Google Inc.

Preparation

Both the Solera Family Room and Screen Room are

designed the same. The installation instructions will be the

same for both products.

NOTE: Conrm proper room size. Measure existing awning

from center of arm to center of arm. Room size must match

awning size. A smaller room cannot be installed on a

longer awning.

Resources Required

• 2 people

• Cordless or Electric Drill or Screw Gun

• Appropriate Drive or Drill Bits

• ¼” Hex Head Bit

• Mallet or Hammer

• Measuring Tape

• Ladder

• Sealant

• Non-permanent method of marking

FAILURE TO FOLLOW THE INSTRUCTIONS PROVIDED

IN THIS MANUAL MAY RESULT IN DEATH, SERIOUS

INJURY, UNIT DAMAGE, OR VOIDING OF THE

COMPONENT WARRANTY.

FOR AWNINGS WITH WIND SENSORS, THE WIND

SENSOR MUST BE SHUT OFF WHEN USING THE ROOM.

IF THE AWNING SHOULD RETRACT AFTER THE ROOM

IS SET UP, DAMAGE TO THE AWNING, ROOM AND UNIT

WILL OCCUR, AS WELL AS POSSIBLE PERSONAL

INJURY. REFER TO THE AWNING OWNER’S MANUAL

FOR INSTRUCTIONS.

MOVING PARTS CAN PINCH, CRUSH OR CUT. KEEP

CLEAR AND USE CAUTION.

lippertcomponents.com 574-537-8900 Rev: 01.17 - Solera®Family and Screen Room

Solera®Family and

Screen Room

Installation and Owner’s Manual

(For Aftermarket Application)

Installation

1. Extend the awning out completely according to the

manufacturer’s instructions. Ensure that the open roll tube

slot and the slot access is down and accessible. Set and

secure both rafters, if applicable.

Install Upper Brackets

1. Place the upper bracket (Fig.1A) directly under the

awning rail so the hook is approximately 2” under the

awning fabric and the end of the bottom of the “L”

portion of the bracket is directly under the edge of the

awning fabric (Fig.1).

2. Mark the bracket location. Apply a liberal amount of

sealant to the back of the bracket. Attach the bracket using

the screws provided.

3. Repeat the process on the opposite side.

NOTE: Molly rivets may be required if no backer material is

present (not provided).

Attach the Side Panels

1. Measure from the awning rail to the ground.

A. For awning rails between 96” and 110”: Attach the

side panel to the upper bracket using the LOWER strap

on the side panel (Fig.2).

B. For awning rails between 111” and 130”: Attach the

side panel to the upper bracket using the UPPER strap on

the side panel (Fig.2).

2. Hang the upper or lower strap, depending on the awning

rail height, on the bracket (Fig.3).

Fig.1

upper strap

lower strap

Fig.2

Fig.3

lippertcomponents.com 574-537-8900 Rev: 01.17 - Solera®Family and Screen Room

Solera®Family and

Screen Room

Installation and Owner’s Manual

(For Aftermarket Application)

3. On the other end, wrap the strap over the roll tube

(Fig.4) next to the awning fabric. Attach the strap (Fig.5)

and tighten the strap (Fig.6).

4. The wedge zippers on the side panels should be facing

under the awning. To adjust the height of the side panel: zip

up 1 or both zippers to make the appropriate height (Fig.7).

5. Choose the appropriate polycord to slide into

roll tube (Fig.8).

A. If both zippers were closed, use the lowest polycord

and slide the front panel into the roll tube.

B. If the middle zipper was closed, use the middle

polycord and slide the front panel into the roll tube.

C. If neither zippers were closed, use the top polycord

and slide the front panel into the roll tube.

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

lippertcomponents.com 574-537-8900 Rev: 01.17 - Solera®Family and Screen Room

Solera®Family and

Screen Room

Installation and Owner’s Manual

(For Aftermarket Application)

6. Run the polycord through to the other end of the roll tube

(Fig.9 and Fig.10).

8. Zip the front panel to the side panels on both sides

(Fig.11).

9. Velcro the top side panel and front panel together on

both sides (Fig.12).

NOTE: Do not unzip the front from the insert. The front

panel ts various size awnings. Once you have set up

the room you can cut off the other polycords and vinyl

on the front insert if you do not want the room to t other

unit applications.

7. Repeat steps 1 through 6 for the 2nd side panel.

Fig.9

Fig.10

Fig.11

Fig.12

lippertcomponents.com 574-537-8900 Rev: 01.17 - Solera®Family and Screen Room

Solera®Family and

Screen Room

Installation and Owner’s Manual

(For Aftermarket Application)

Install Unit Skirting

NOTE: The room kit comes with a unit skirt panel and

a shorter, wheel well cover panel. Both will be attached

to the unit with self-adhesive fasteners. The attachment

points for the fasteners on the unit must be clean and dry.

It may be necessary to use rubbing alcohol on the area

before attaching the adhesive snaps to remove dirt and

moisture. The optimum temperature should be above 50°.

1. Attach all of the included self-adhesive fasteners to the

snaps on the unit skirt panel (Fig.13).

2. Starting at one end of the unit skirt panel, remove the

backing of the rst adhesive snap and attach it to the unit

approximately 2” outside of the room’s side panel (Fig.14).

3. Move to the next fastener and repeat process

keeping the skirt in a straight line. (If the skirt covers a

compartment, simply unsnap the skirt when using the

room to obtain access to the compartment.)

4. If the wheel well opening is not covered completely

by the room skirt, use the wheel well skirt to cover the

opening using the self-adhesive fasteners (Fig.15). Once

the wheel well skirt is installed, tuck the bottom of the skirt

behind the room skirt (Fig.15).

5. If the unit skirt panel goes across the entry step:

A. With the panel attached to the unit wall, carefully mark

the location of the top, inner and outer edges of the step

frame on the skirt.

B. Remove the skirt from the unit and lay out on a at,

clean surface (Fig.16).

THE SKIRTING MUST NOT INTERFERE WITH LP

APPLIANCE OR EXHAUST VENTS. DO NOT START OR

OPERATE THE UNIT’S ENGINE OR UNIT GENERATOR

IF THE EXHAUST COMPONENTS ARE LOCATED

BEHIND THE SKIRTING.

Fig.13

Fig.14

Fig.15

Fig.16

heating vent

lippertcomponents.com 574-537-8900 Rev: 01.17 - Solera®Family and Screen Room

Solera®Family and

Screen Room

Installation and Owner’s Manual

(For Aftermarket Application)

Securing the Room to the

Ground

1. Place a ground spike through the bracket on the side

tensioner. Hammer the spike into the ground, preferably

slightly under the RV. This will keep the side panel snug

against the unit.

2. Pull the shock cord through to tighten the side panel.

3. Position the room so the sides and front panel

look square.

4. Start at the side panel and use the grommet closest to

the unit. Place the spike through the grommet and hammer

the spike into the ground.

C. Using a straight edge and sharp knife, draw and then

cut out 3 sides on the skirt (Fig.17).

D. This creates a ap in the fabric.

6. Reattach the skirt to the unit.

7. Pull steps out through the ap (Fig.18). Tuck the ap

behind the stairs (Fig.19).

5. Set the remaining spikes in the grommets in the

following order: Side panel closest to the door; front panel

near the opposite side panel; unit side; opposite side from

where you started.

6. Set all remaining spikes.

Removing Spikes

1. Using vise grips or pliers, grab the head of the spike and

twist 3 or 4 times, then lift the spike out of the ground.

Fig.17

Fig.18

TO AVOID TEARING THE ROOM, HIT THE SPIKE

DIRECTLY ON THE HEAD. DO NOT POUND THE SPIKE

DOWN TOO HARD.

Fig.19

lippertcomponents.com 574-537-8900 Rev: 01.17 - Solera®Family and Screen Room

Solera®Family and

Screen Room

Installation and Owner’s Manual

(For Aftermarket Application)

Manual information may be distributed as a complete

document only, unless Lippert Components provides

explicit consent to distribute individual parts.

All manual information is subject to change without

notice. Revised editions will be available for free

download at www.lippertcomponents.com. Manual

information is considered factual until made obsolete

by a revised version.

Please recycle all obsolete materials and contact

Lippert Components with concerns or questions.

NotesStoring The Panels

1. Ensure that the privacy panels are down and secured.

2. Remove the spikes holding the panels.

3. Reverse the setup procedures to remove the panels.

4. Store the spikes in the small storage bag.

5. To fold the panels:

A. Lay the panels at with the screen panel facing up.

B. Square the side panel by folding the triangular

shape over.

C. Fold the top over and down to the bottom edge.

D. Fold in half until the panel is approximately a

12” segment.

E. Starting on one end, fold the panel in approximately

24” segments.

F. Store the panels in the storage bags.

5 0 6 23 5 - S O L- I NS TA L-1/ 17

Autres manuels pour Solera

Table des matières

Manuels Tente populaires d'autres marques

OZTENT

OZTENT JV SIGNATURE EDITION Manuel utilisateur

GigaTent

GigaTent Summer Chalet Mini Tent Manuel utilisateur

Coleman

Coleman 2000007827 Manuel

ShelterLogic

ShelterLogic 107153 Manuel utilisateur

Outsunny

Outsunny 84C-230 Manuel utilisateur

Napier

Napier SPORTZ COVE 61 Series Manuel utilisateur

EuroTrail

EuroTrail ATLANTIS PRO Manuel utilisateur

Reimo

Reimo Marina Manuel utilisateur

TiiTENT

TiiTENT TB300 Manuel utilisateur

Coleman

Coleman 2000033134 Guide d'installation

Ozark Trail

Ozark Trail W784.1 Guide de démarrage rapide

SlingFin

SlingFin CrossBow 2 Manuel utilisateur

Coleman

Coleman 9600-141 Manuel utilisateur

Palram

Palram Arizona 5000 Wave - WINGS Manuel utilisateur

COVERPRO

COVERPRO 56184 Instructions de montage

Vango

Vango Zenith 100 Manuel utilisateur

Costway

Costway PATIOJOY OP70818 Manuel utilisateur

Clarke

Clarke PUC 88 Manuel utilisateur