LinTronic BT-RS232 Manuel utilisateur
BlueTooth
receiver BT-RS232
for BeoRemote One
LinTronic
Updated: 200803
DISCLAIMER
The functionality of the BT-RS232 is based on the bluetooth commands transmitted
by the “BeoRemote One Bluetooth” remote control produced by
Bang&Olufsen, Denmark: https://www.bang-olufsen.com
The BT-RS232 is developed in March 2020 without any assistance from Bang&Olufsen.
Bang&Olufsen is not responsable for the functionality/software of the BT-RS232.
LinTronic is not responsable for the functionality/software of the
“BeoRemote One Bluetooth”.
By taking the BT-RS232 into use, you accept these terms.
August 2020
Michael Lindgaard
LinTronic.dk
Updated: 200803
TT455-RT-238
(infrared)
BT-RS232
(bluetooth)
The Beoremote One Bluetooth can transmit both infrared (IR) and bluetooth (BT)
signals.
Our TT455-RT-238 will receive the IR signals and control your non-B&O audio/video
products, relays, etc. See http://lintronic.dk/hw6.pdf
Our BT-RS232 wil receive the BT signals and convert them into RS232.
The BT-RS232 can be connected to your homeautomation system, controller
(AMX, Crestron, Control4, etc.). Also the BT-RS232 can send the BT signals
(shaped as RS232 commands) to the TT455-RT-238 and this way control your
existing audio/video products by BT converted into IR.
Beoremote One Bluetooth
(infrared and Bluetooth)
Also see:
http://lintronic.dk/NiceToKnowWhenOrdering.pdf
BT-RS232
(bluetooth)
IR RECEIVER
TT455-RT-238
(infrared)
Beoremote One
Bluetooth
Beoremote One Infrared
or Beo4
Two remotes at the same time ?
Yes, it is possible to control the TT455-RT-238 with an IR and a BT remote at the same time.
Please observe that the modes for the IR remote and the modes for the BT remote, are
considered at different modes.
Example: TV mode on the IR remote and TV mode on the BT remote, are two different modes.
This allows you to control the same TV with the two remotes or two different TV’s (or other
products).
85 mm
56 mm
Pairing button
LED, indicates status of BT-RS232
USB micro - 5 volt power supply and cable not included
RS232 - standard SUBD9 female
Pin 2 Tx data
Pin 3 RX data
Pin 5 Ground
Dimensions 1:1
Bluetooth logo is not printed on cabinet.
BT-RS232
27 mm
BT-RS232 POWER SUPPLY
https://www.ikea.com/dk/da/p/koppla-usb-stik-med-1-udgang-hvid-40412278/
BT-RS232 is powered by a standard 5 Volt USB charger.
We are not able to be price competitive on chargers.
Be advised that IKEA offer a charger at only 5 Euro’s
and a USB Micro cable at only 2 euro’s.
https://www.ikea.com/dk/da/p/lillhult-mikro-usb-til-usb-kabel-sort-hvid-70464807/
BT-RS232
LED’s blink patterns
Not paired Blinks Red, 0,5 seconds On, 0,5 seconds Off
Paired but not connected Blinks Green, 0,5 seconds On, 0,5 seconds Off
Paired and connected Constant Green, On
Paired, receiving data Blinks Green, Off/On, when receiving data
Bootload check Blinking Red, 5 times pr. second
How to pair the BT-RS232 and the Beo Remote One Bluetooh
Activate the pairing button of the BT-RS232 - the LED starts flashing fast.
Activate the LIST button of the BeoRemote One Bluetooth.
The remote controls display will show “Settings”.
Activate the OK/SELECT button of the BeoRemote One Bluetooth.
The remote control display will show
“Settings” click OK
“Pairing” click OK
“Pair” click OK
“Open for pairing”
A few seconds later:
Paired with
BT-RS232
Ready for use
Pairing button
TV
MUSIC
SETTINGS
TV
MUSIC
PAIRING
TV
MUSIC
PAIR
TV
MUSIC
OPEN FOR PAIRING
TV
MUSIC
PAIRED WITH
BT-RS232
Ready for use
TV
MUSIC
7 8 9
4 5 6
1 2 3
LIST 0 GUIDE
INFO
P+
OP- -
+
>
>
>
>
BeoRemote One
Bluetooth
USER 1
USER 3
USER 2
USER 4
MODES
TRIGGERS
This page shows how we support
the BeoRemote One Bluetooth.
The upper 6 buttons are considered modes and
all other buttons are considered triggers.
BANG&OLUFSEN
P+
P-
>
>
>
>
BeoRemote One
Bluetooth
SHORT/LONG ACTIVATION
Some of the buttons on the BeoRemote One Bluetooth (BR1BT), keep sending the same command
repeatedly if you hold the button activated. The buttons are shown below.
We have introduced a new feature which counts the number of received commands, (in other words,
detects how long you hold one of the R-buttons activated) and after a certain number of commands
are received (repeat-count), the configurator and the TT455-RT-238 firmware, will allow you to carry
out a new function called “R-long”.
This will give you 6 more commands in each mode, in total 36 more commands.
You can set the number of R-commands to be received (repeat-count) before the RX-command is
considered an R-long-command.
When you activate any of the below R-commands, the software will introduce a short delay while
counting how many commands are received. If you release the button before the repeat-count
number is received, then the command is executed. If you hold the button long enough for the
repeat-count number to be reached, then the R-long command is executed. This is easy to check
and adjust in the Configurators Memory Map / Settings.
Please be advised that the trigger-numbers for the X-long commands are determined by LinTronic.
If we later find thatthe BR1BT use these numbers for original B&O commands, then we either have to
change them og skip this function.
Channel_Up
Channel_Up_Long
Channel_Down
Channel_Down_Long
Up
Up_Long
Left
Left_Long
Right
Right_Long
Down
Down_Long
R-buttons
The default RepeatCount is 5.
Our Bluetooth receiver BT-RS232
reads signals from a Bang&Olufsen
BeoRemote One Bluetooth remote control.
The receiver pairs with the BeoRemote One
and sends out the detected Bluetooth signal
as an RS232 command.
The BT-RS232 will work with the TT455-RT-238 HW6.x
and any computer, controller or homeautomation system
capable of communicating RS232C:
19200 bps, no parity, 8 databits, 1 stopbit
This allows our TT455-RT-238 to be triggered by bluetooth
in order to control IR products, relays, tv-stands, etc.
but it also allows home-automation installers to use BT-RS232
to receive Beoremote One Bluetooth commands,
for their optional use, even without having a TT455-RT-238.
LinTronic’s OPEN SOURCE protocol:
http://lintronic.dk/LinTronicProtocol.zip
Simply explained “get started guide” on RS232:
http://lintronic.dk/rs232.pdf
NOTE:
The BT-RS232 works out of the box, no configuration is needed.
Default pairing name is “BT-RS232”. If you buy more than one BT-RS232,
then you can individually rename the BT-RS232 modules, making it easy to swap
between them. If you want to change the pairing name, the BT-RS232 must be
connected to a computer with a terminal program capable of sending a renaming
command on a comport. The LinTronic Configurator is recommended.
The LinTronic Configurator is required for verification of possible firmware updates.
