LINOVISION IOT-S500L Manuel utilisateur

Updated on Sept. 10, 2021

IOT-S500L

LoRaWAN® PIR & LightSensor

Safety Precautions

Linovision will not shoulder responsibility for any losses or damages resulting from not

following the instructions of this operating guide.

❖The device must not be modified in any way.

❖Do not expose the PIR lens to direct sunlight.

❖Do not paint or clean the PIR lens, or it will affect the detection of the device.

❖Do not place the device where the temperature is below/above the operating range.

❖Do not place the device close to objects with naked flames, heat source (oven or sunlight),

cold source, liquid and extreme temperature changes.

❖The device is not intended to be used as a reference sensor, and Linovision will not

take responsibility for any damages which may result from inaccurate readings.

❖When installing the battery, please install it accurately, and do not install the reverse or

wrong model.

❖Remove the battery if the device will not be used for a long time. Otherwise, the battery will

leak and damage the device.

❖The device must never be subjected to shocks or impacts.

Declaration of Conformity

IOT-S500L conforms with the essential requirements and other relevant provisions of the CE,

FCC, and RoHS.

For assistance, please contact

Linovision technical support:

Email: sales@Linovision.com

Tel: +86571-86708175

Revision History

Date

Doc Version

Description

July 15,2021

V 1.0

Initial version

Sept. 10,2021 V 1.1

1. Add LoRa D2Dfeature;

2. Support light collection enabled/disabled;

3. Delete low power alarm interval, device only

uplinks once when battery level is lower than

10%.

Contents

1. Product Introduction .................................................................................................................................... 5

1.1Overview .............................................................................................................................................. 5

1.2Features ...............................................................................................................................................5

2. HardwareIntroduction.................................................................................................................................. 5

2.1PackingList ......................................................................................................................................... 5

2.2HardwareOverview ............................................................................................................................. 6

2.3Dimensions......................................................................................................................................... 6

2.4LED Patterns....................................................................................................................................... 6

3. OperationGuide .............................................................................................................................................7

3.1NFC Configuration............................................................................................................................. 7

3.2LoRaWAN Settings..............................................................................................................................7

3.3GeneralSettings................................................................................................................................ 10

3.4ThresholdSettings............................................................................................................................ 11

3.5LoRa D2DSettings.............................................................................................................................11

3.6Maintenance..................................................................................................................................... 1 2

3.6.1Upgrade................................................................................................................................... 12

3.6.2Backup .................................................................................................................................... 12

3.6.3Reset to Factory Default ....................................................................................................... 13

4. Installation .................................................................................................................................................. 14

5. DevicePayload.......................................................................................................................................... 14

5.1Basic Information............................................................................................................................. 15

5.2Sensor Data ........................................................................................................................................15

5.3DownlinkCommands........................................................................................................................1 6

1. Product Introduction

1.1 Overview

IOT-S500L is a PIR sensor based on passive infraredtechnologyto detect a motionor

occupancy. IOT-S500L can detect whether there is a movement within the range of 6-8m.

Besides, IOT-S500L equips with a light sensor which can link PIR detection results to trigger

scenes. IOT-S500L can be widely used in smart homes, smart offices, schools, warehouses, etc.

Sensor data are transmitted in real-timeusing the standard LoRaWAN® protocol. LoRaWAN®

enables encrypted radio transmissions over long distances while consuming very little power.

The user can get an alarm through Linovision IoT Cloud or through the user's own

Application Server.

1.2Features

●Built-inlight sensor, combine PIR sensor to achieve triggers

●Up to 15 km communication range

●Easy configurationvia NFC

●Standard LoRaWAN®support

●Compatible with Milesight IoT Cloud

2. Hardware Introduction

2.1Packing List

1 ×

IOT-S500L

Sensor

2 ×

Wall Mounting Kits

1 ×

3M Tape

1 ×

Quick Guide

If any of the above items is missing or damaged,please contact yoursales representative.

2.2 Hardware Overview

2.3 Dimensions (mm)

2.4LED Patterns

Function

Action

LED Indicator

PIR Detection PIR is triggered (network unregistered) Red, blink once

PIR is triggered(network registered) Green, blink once

Network Status Send join network requests Red, blinks once

Joined the network successfully Green, blinks twice

Reboot Press and hold the reset button for more than 3s Slowly blinks

Reset to Factory

Default Press and hold the reset button for more than 10s Quickly blinks

3. Operation Guide

3.1NFC Configuration

IOT-S500L can be configured via an NFC-enabledsmartphone.

1. Pull out the battery insulating sheet to power on the device. The indicator will light up in green for 3

seconds when the device turns on.

2. Download and install “ToolBox” App from Google Play or App Store.

3. Enable NFC on the smartphone and open Milesight ToolBox.

4. Attach the smartphone with NFC area to the device to read device information.

5. Basic information and settings of the device will be shown on ToolBox if itʼs recognized

successfully. You can read and configure the device by tapping the Read/Write device on the

App. In order to protect the security of the device, password validation is required when

configuring via a new smartphone. The default password is 123456.

Note:

1) Check the location of the smartphone NFC area and itʼs recommended to take off the phone

case.

2) If the smartphone fails to read/write configurations via NFC, move the phone away and back

to try again.

3) IOT-S500L can also be configured by ToolBox software via a dedicated NFC reader

provided by IoT, you can also configure it via TTL interface inside the device.

3.2LoRaWAN Settings

LoRaWAN settings are used for configuringthe transmission parameters in LoRaWAN®network.

Basic LoRaWAN Settings:

Go to Device ->Setting ->LoRaWAN Settings of ToolBox App to configure join type, App EUI, App

Key and other information. You can also keep all settings by default.

Parameters

Description

Device EUI Unique ID of the device which can also be found on the label.

App EUI Default App EUI is 24E124C0002A0001.

Application Port The port used for sending and receiving data. The default portis 85.

J oin Type OTAA and ABP modes are available.

Application Key Appkey for OTAA mode, default is 5572404C696E6B4C6F52613230313823.

Device Address DevAddrfor ABP mode, default is the 5th to 12th digits of SN.

NetworkSession

Key Nwkskey for ABP mode, default is 5572404C696E6B4C6F52613230313823.

Application

Session Key Appskey for ABP mode, default is 5572404C696E6B4C6F52613230313823.

Spread Factor If ADR is disabled, the device will send data via this spread factor.

Confirmed Mode If the device does not receive ACK packet from network server, it will resend

data 3 times at most.

Rejoin Mode

Reporting interval ≤ 30 mins: device will send specific mounts of LoRaMAC

packets to check connection status every 30 mins; If no reply after specific

packets are being sent, the device will re-join.

Reporting interval > 30 mins: device will send specific mounts of LoRaMAC

packets to check connection status at every reportinginterval; If no reply after

specific packets are being sent, the device will re-join.

ADR Mode Allow network server to adjust data rate of the device.

Tx Power Transmit power of device.

Note:

1) Please contact sales representative for device EUI list if there are manyunits.

2) Please contact sales representative if you need random App keys before purchase.

3) Select OTAA mode if you use IoT Cloudto manage devices.

4) Only OTAA mode supports rejoin mode.

LoRaWAN Frequency Settings:

Go to Setting->LoRaWANSettings of ToolBox App to select the supported frequency and select

channels to send uplinks.Make sure the channels match the LoRaWAN®gateway.

If device frequency is one of CN470/AU915/US915,you can enter the index of the channel that

you want to enable in the input box,making them separated by commas.

Examples:

1,40: Enabling Channel 1 and Channel 40

1-40:Enabling Channel 1 to Channel 40

1-40,60:Enabling Channel 1 to Channel 40 and Channel 60

All: Enabling all channels

Null: Indicates that all channels are disabled

Note:

For -868Mmodel, default frequency is EU868;

For -915Mmodel, default frequency is AU915.

3.3 General Settings

Go to Device->Setting->GeneralSettingsof ToolBox App to change the reporting interval, etc.

Parameters

Description

Reporting Interval

The interval of reporting PIR, light status and battery level to network

server. Default: 30 mins, Range: 1 -1080 mins

Note: IOT-S500L will also report “triggered”status of PIR sensor

immediately when it detects motions.

Idle Time When the PIR sensor does not detect motion for a period of Idle Time,

Table des matières

Autres manuels LINOVISION Accessoires

LINOVISION

LINOVISION IOT-S500 Series Manuel utilisateur

LINOVISION

LINOVISION IOT-S500-IAQ3 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur