Linksys SPA3102 Manuel utilisateur

Cluana

Linksys Cisco FXO adapter SPA 3102 Configuration guide

Cable connection

Step 1: connect your p one cable to t e “PHONE” port. Leave the “LINE” port disconnected.

Step 2: connect your LAN cable to t e “INTERNET” port. We assume a DHCP server is already running on

your LAN. If not, after step 3 jump to “Static IP configuration”

Step 3: power up t e adapter

IP address detection and web management

On your p one

–press **** (star key 4 time)

–press 110# and take note of t e annouced IP address. Let's call it “ip_address”

–press 7932# 1# 1 (it's needed to enable web management on t e internet port)

–open a web browser to t e URL: ttp://ip_address/admin/advanced

Adapter configuration

Let's assume t e followings:

Your PBX company domain is m compan .com (provided by Cluana).

Your PBX ostname is m server.cluana.com (provided by Cluana)

Your analog adapter User ID / Aut ID is fxo_1 (your c oice)

Your analog adapter password is : password (your c oice)

Your p one line PSTN number is YOUR_NUMBER (0733784374 in t e picture below)

Open SIP tab

RTP Parameters section

RTP Packet Size: 0.020

Open PSTN Line tab

Proxy and Registration

Proxy: m compan .com:5061

Outbound Proxy: m server.cluana.com:5061

Use Outbound Proxy: Yes

Subscriber Information

Display name: FXO_1

User ID: fxo_1

Password: password

Use aut ID: Yes

Aut ID: fxo_1

Audio Configuration

Preferred Codec: G711a (G711u for USA)

Dial Plans

Dial Plan 2: (S0<:YOUR_NUMBER>)

PSTN-To-VoIP Gateway Setup

PSTN Ring T ru Line 1: no

PSTN CID For VoIP CID: yes

PSTN Caller Default DP: 2

FXO Timer Values (sec)

PSTN Answer Delay: 2

PSTN Disconnect Detection

Disconnect Tone:

US: 480@-30,620@-30;4(.25/.25/1+2)

UK: 400@-30,400@-30; 2(3/0/1+2)

France: 440@-30,440@-30; 2(0.5/0.5/1+2)

Germany: 440@-30,440@-30; 2(0.5/0.5/1+2)

Net erlands: 425@-30,425@-30; 2(0.5/0.5/1+2)

Sweden: 425@-10; 10(0.25/0.25/1)

Norway: 425@-10; 10(0.5/0.5/1)

Italy: 425@-30,425@-30; 2(0.2/0.2/1+2)

Spain: 425@-10; 10(0.2/0.2/1,0.2/0.2/1,0.2/0.6/1)

Portugal: 425@-10; 10(0.5/0.5/1)

Poland: 425@-10; 10(0.5/0.5/1)

Denmark: 425@-10; 10(0.25/0.25/1)

New Zealand: 400@-15; 10(0.25/0.25/1)

Australia: 425@-13; 10(0.375/0.375/1)

International Control

FXO Port Impedance:

US: 600

EU (UK, Germany, Net erlands, Sweden, Norway, Italy,

Spain, Portugal, Poland, and Denmark): 270+750||150nF

France: 270+750||150nF

Australia: 220+820||120nF

New Zealand: 370+620||310nF

Press "Submit all c anges"

Now you can connect your p one line cable to t e “LINE” port.

Firmware Upgrade

Configuration parameters above were tested wit firmware release 5.2.13 . If your adapter is using an older

release (c eck Voice menu, Info->Product Information->Software Version) maybe a software upgrade is

needed.

•Download t e latest firmware from t e adapter manufacturer support site

•Extract t e Zip file, and t en run t e executable file to upgrade t e firmware.

•W en t e Firmware Upgrade Warning window appears, click Continue.

•In t e next window t at appears, enter t e IP address of t e ATA device, and t en click OK.

•In t e Confirm Upgrade window, verify t at t e correct device information and product number

appear. T en click Upgrade.

•A progress message appears w ile t e upgrade is in progress.

•T e success window appears w en t e upgrade is completed. T e device reboots. Click OK to close

t e confirmation message.

•To verify t e upgrade, point t e web browser to t e IP address of t e ATA device

Static IP configuration

We recommend to use a DHCP server on your Local Area Network in order to allow your adapter to

automatically configure its network parameters. S ould you need to assign a static IP address, please follow

t e Quick Install guide provided wit your adapter. Remember t at you need to find a free IP address

compatible wit your network and assign via IVR commands suc IP address and its netmask (eg.

192.168.1.100 and 255.255.255.0) . Suc parameters s ould be enoug to access t e device via web

browser and allow you to configure any ot er value.

Factor Reset

You can restore factory default settings wit t e following steps:

on your p one

–press **** (star key 4 time)

–press 73738#

–press 1

–angup

Autres manuels pour SPA3102

Table des matières

Autres manuels Linksys Adaptateur

Linksys

Linksys WPC300N Manuel utilisateur

Linksys

Linksys WGA11B Manuel d'utilisation

Linksys

Linksys WPC200 Manuel d'utilisation

Linksys

Linksys HU200 Manuel utilisateur

Linksys

Linksys PLE200 - PowerLine AV EN Adapter Bridge Manuel utilisateur

Linksys

Linksys WPC200 Manuel utilisateur

Linksys

Linksys WPC54GR (DE) Instructions d'utilisation d'origine

Linksys

Linksys Small Business SPA2102 Instructions d'utilisation d'origine

Linksys

Linksys WUSB12 Instructions d'utilisation d'origine

Linksys

Linksys SPA 2102 ATA Manuel utilisateur

Linksys

Linksys WPC4400N Manuel d'utilisation

Linksys

Linksys EC1000 Manuel utilisateur

Linksys

Linksys USB300M Manuel utilisateur

Linksys

Linksys SPA1 Series Manuel utilisateur

Linksys

Linksys PAP2 Manuel utilisateur

Linksys

Linksys Instant PowerLine PLUSB10 Manuel utilisateur

Linksys

Linksys WUSB11 ver. 2.6 Manuel utilisateur

Linksys

Linksys WGA54G Manuel utilisateur

Linksys

Linksys WGA54AG Manuel utilisateur

Linksys

Linksys WUSB11 ver. 2.6 Manuel utilisateur

Linksys

Linksys SPA2102-NA - VOIP Router 2 FXS RJ45 Manuel utilisateur

Linksys

Linksys WPC54GX Manuel utilisateur

Linksys

Linksys WUSB54GC EU Manuel utilisateur

Linksys

Linksys WPC54GR (DE) Instructions d'utilisation

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur