Link LK-CHR17CL Manuel utilisateur
LINK
INSTALLATION MANUAL
LK-CHR17CL
CHRYSLER PACIFICA
2017 &UP
DRIVER SIDE 2nd ROW
LINK CHRYSLER PACIFICA 2017 & UP CENTER LEFT. p. 2
WARNINGS
PLEASE REVIEW BEFORE STARTING THE INSTALLATION
Look through the entire manual to understand the installation process.
Watch the tutorial videos that are found on the tablet.
During the installation use the ‘BYPASS’ mode to move the LINK.
Do not use the pendant or ‘PENDANT’ mode until you have reset the home position.
The LINK is designed to ALWAYS use the original seat. The biggest challenge this will present for the installer will
be extending the vehicle’s original seat wire harness, as this MUST be done. The general process does not vary, but
the exact steps will vary due to the trim level, the model and seat options from the vehicle manufacturer. Keeping
this in mind, we have made an effort to clearly describe the process required in this manual. However, it is possible
that the pictures in this manual do not exactly match the specific vehicle you are working on.
SEAT WIRING EXTENSION PROCESS
The wiring must be extended 80 inches. This extension is placed near the seat connectors that are under the seat.
The extension (80 inches) then passes under the LINK and loops around the back of the OEM seat –allowing the
seat and the LINK to travel in and out of the vehicle. Depending on the make, model and seat options, there are
components that must be disconnected, bypassed and/or relocated. On vehicle models with a seat position memory
function, the forward/backward, tilt and height adjustments as well as seat memory are replaced by the LINK.
However, the seat recline function is retained. (EXAMPLE: In the Ford F150, 2009-2014 model; the seat height, tilt,
forward and backward adjustment motors are disconnected and removed with the seat frame, but the recline motor
is retained. The control and memory box are relocated to the floor under the seat, next to the seat connectors. The
seat position sensor is also relocated to the floor under the seat. The wiring harness is then extended from this point
under the seat.)
PLEASE NOTE: If the ignition is turned on while extending a wire harness that includes airbags, this may cause the
airbag light to stay on following the installation.
ADAPT SOLUTIONS CANNOT BE HELD RESPONSIBLE FOR FAULTY WIRE EXTENSIONS.
Please use caution during the installation.
ANDROID TABLET –LINK I.T. SOFTWARE
If this is your first installation of a LINK, you will have also purchased an Android tablet that is required for the
installation and maintenance of the LINK product. This tablet will have the LINK IT software already installed. We
have prepared quick, easy and to the point tutorial videos imbedded into the software. Take a moment and watch
the video that shows all the features of the tablet. To do this, open the LINK IT app and tap on ‘INFO’. Make sure
your volume is turned up and tap on App-101. The video will start automatically.
REDUCED POWER MODE
A safeguard is integrated in the LINK system. Following any changes to the preset or sequence of the LINK, the
unit will enter a reduced power mode. This is to allow you to visually inspect the movements of the LINK to ensure
it is not damaging the vehicle or itself during its first cycle. On the tablet, a yellow bar will appear at the top of the
screen to indicate you are in reduced power mode. To exit, simply run the LINK a full cycle. NOTE:It is possible that
the LINK will stop during this cycle as power is reduced. Visually confirm nothing is impeding the movements and
then simply press the IN or OUT button again to continue the cycle. During the installation, if the 12V power is
removed and replaced at the same time as the 9V battery (LINK memory back up) is unplugged or fully drained, the
LINK will enter reduced power mode. Simply run a full cycle to exit. PLEASE NOTE: You will find an explanation of
this mode on a YELLOW tag attached to the hand pendant. Please explain the functions of the reduced power mode
to the LINK user (your client).
For technical support call 866.641.0419 or email tech@adaptsolutions.com
Please have the serial number of the unit on hand before placing your call.
10
12
13
11
1
14
8
9
7
6
2
15
4
5
18
17
319
16
1 of 4
22
20
21
23
ITEM
PART NUMBER
QTY
DESCRIPTION
1
LK000L-01
1
Short Model LINK -Left-
2
LK-UNI-005L
1
005 Assembly Top Bearing Plate -Left-
3
LK-CHR17CL-04
1
Support Pivot -Left Central-
4
LK-CHR17CL-03
1
Seat Adapter -Left Central-
5
L-LK912
1
Communication Cable Support
6
PRD 333-107
4
Nylon Insert Locknut 5/16-18
7
PRD 339-136P
4
Socket Shoulder Screw Zinc Plated 3/8 x 1/2 x 5/16-18 THD
8
LK710B
1
Chain Covert -Black-
9
PRD 110-106
2
Round washer head tapping screw #8 x 3/4
10
LK750LB
1
Pivot Cover -Left- Black
11
LK730LB
1
Outside Cover -Left- Black
12
LK731LB
1
Intside Cover -Left- Black
13
PRD 251-177
4
Trim Panel Clip Ø1/4'' x 3/4'' Black
14
LK700B
1
Link Covert -Black-
15
LK720LB
1
Pivot Motor Cover -Left- Black
16
LK960
1
LINK Wired Control
17
LK-CHR17C-01
1
Floor Bottom Adapter -Central-
18
LK-CHR17CL-02
1
Floor Upper Adapter -Left Central-
19
LK-CHR17CB-05
2
Floor Upper Adapter Cover -Central- Black
20
LK-CHR17C-BK
1
Bolt Kit -Central-
21
LK-CHR17C-AB
1
Heated Seat Airbag LINK Kit -Central-
22
EW-CK-00
1
12V Power Supply Wiring Kit
23
LK-UNI-650
1
Manual Backup Tool Kit
LK-CHR17CL
ADAPT SOLUTIONS
|[email protected]|866.641.0419|418.889.9838 fax
PART NUMBER
LINK Chrysler Pacifica 2017 & Up -Left Central-
DESCRIPTION
LINK CHRYSLER PACIFICA 2017+ -CENTRAL-
6
5
1
2
4
Step 1: Drill Ø5/16 (2 thickness)
Step 2: Drill: 3/16"
Step 3: Thread 1/4 - 20 UNC
1
3
A
2 of 4
Drill Ø3/16"
Thread: 1/4 - 20 UNC
Drill: 5/16
DETAIL A
SCALE 1 : 1
ITEM
PART NUMBER
QTY
DESCRIPTION
1
LK000L-01
1
Short Model LINK -Left-
2
LK-UNI-305L
1
305 Top Bearing Plate -Left-
3
LK-CHR17CL-04
1
Support Pivot -Left Central-
4
PRD 192-141
1
Spring Tensions Pin 3/16 x 3/4
5
PRD 337-193P
1
Socket Head Cap Screw Zinc Plated 1/4-20 UNC x 3/4
6
PRD 337-213P
3
Button head socket cap screw Zinc Plated 5/16-18 x 3/4
LK-CHR17CL
ADAPT SOLUTIONS
|[email protected]|866.641.0419|418.889.9838 fax
PART NUMBER
LINK Chrysler Pacifica 2017 & Up -Left Central-
DESCRIPTION
LINK CHRYSLER PACIFICA 2017+ -CENTRAL-
1
5
910
8
4
7
2
3
6
3 of 4
ITEM
PART NUMBER
QTY
DESCRIPTION
1
LK-CHR17CL-03
1
Seat Adapter -Left Central-
2
LK710B
1
Chain Covert -Black-
3
LK730LB
1
Outside Cover -Left- Black
4
LK731LB
1
Intside Cover -Left- Black
5
LK750LB
1
Pivot Cover -Left- Black
6
L-LK912
1
Communication Cable Support
7
PRD 110-106
2
Round washer head tapping screw #8 x 3/4
8
PRD 251-177
4
Trim Panel Clip Ø1/4'' x 3/4'' Black
9
PRD 333-107
4
Nylon Insert Locknut 5/16-18
10
PRD 339-136P
4
Socket Shoulder Screw Zinc Plated 3/8 x 1/2 x 5/16-18 THD
LK-CHR17CL
ADAPT SOLUTIONS
|[email protected]|866.641.0419|418.889.9838 fax
PART NUMBER
LINK Chrysler Pacifica 2017 & Up -Left Central-
DESCRIPTION
LINK CHRYSLER PACIFICA 2017+ -CENTRAL-
5
1
2
11
12
10
13
3
6
7
8
4
9
4 of 4
ITEM
PART NUMBER
QTY
DESCRIPTION
1
LK-CHR17C-01
1
Floor Bottom Adapter -Central-
2
LK-CHR17CL-02
1
Floor Upper Adapter -Left Central-
3
LK-CHR17CB-05
2
Floor Upper Adapter Cover -Central- Black
4
LK-CHR17C-AB
1
Heated Seat Airbag LINK Kit -Central-
5
LK700B
1
Link Covert -Black-
6
LK720LB
1
Pivot Motor Cover -Left- Black
7
LK960
1
LINK Wired Control
8
EW-CK-00
1
12V Power Supply Wiring Kit
9
LK-UNI-650
1
Manual Backup Tool Kit
10
PRD 302-220P
6
Hex Cap Bolt Zinc Plated 7/16-14 x 1" G5
11
PRD 332-164P
4
Socket Head Cap Screw Zinc Plated 3/8-16 x 7/8
12
PRD 332-166P
4
Socket Head Cap Screw Zinc Plated 3/8-16 x 1 1/4
13
PRD 341-108P
6
Flat Washer Zinc Plated I.D. 3/8 USS
LK-CHR17CL
ADAPT SOLUTIONS
|[email protected]|866.641.0419|418.889.9838 fax
PART NUMBER
LINK Chrysler Pacifica 2017 & Up -Left Central-
DESCRIPTION
LINK CHRYSLER PACIFICA 2017+ -CENTRAL-
*ESTIMATED height and installation time (base model).
HIGHER TRIM LEVELS REQUIRED ADDITIONAL INSTALLATION TIME.
ADAPT SOLUTIONS
11-2017
LINK REFERENCES
LK-CHR17CL & LK-CHR17CR
Seat height: OEM
*Transfer height: 19”|Average install: 6-8 hrs.
OEM shrouds must be trimmed.
Seat adjustments|FRONT: OEM |BACK: 1 ¾ ” more than OEM
Please specify if equipped with heated seats. (add. parts & time)
Doorsill moulding needs to be cut|STENCIL PROVIDED
NOT AVAILABLE FOR HYBRID MODEL.
OEM shrouds must be trimmed.
LINK CHRYSLER PACIFICA 2017 & UP CENTER LEFT. p. 3
1. Remove the center driver side OEM seat and place on a workbench. Remove and keep the OEM seat
bolts to install the LINK floor adapters. To do this, fold the stow and go seats into their folded position.
2. The stow and go seat section cover will have to be removed to be able to remove the seat. To do this
the plastic door sill trims will have to be removed on both sides to gain access to the bolts that hold the
cover.
LINK CHRYSLER PACIFICA 2017 & UP CENTER LEFT. p. 4
3. Remove the rear section of the floor cover, this section is held by clips.
4. Unbolt all the bolts around the cover and also remove the plastic seat rail trims.
5. Disconnect the two cable connectors for the right and left hand side stow and go cover mechanism.
LINK CHRYSLER PACIFICA 2017 & UP CENTER LEFT. p. 5
6. Remove the stow and go cover to gain access to the seats. Unplug the actuator wiring connector and
then unbolt the two rear seat bolts. Bring the seat out of its stored position to gain access to the lower
retaining bolts, remove the bolts and then remove the seat. Retain the OEM bolts to install the LINK
lower floor adapter.
7. NOTE: Some models may have second row seat heating option. Extend the wiring with the provided
80-inch extension.
8. Install the lower LINK floor adapter # LK-CHR17C-01 using the OEM bolts.
Table des matières
Autres manuels Link Accessoires automobiles
Link
Link LK-RAV19R Manuel utilisateur
Link
Link LK-TOY11CL Manuel utilisateur
Link
Link HD150 Manuel utilisateur
Link
Link DD2000-XLC Manuel
Link
Link LK-SILX07R Manuel utilisateur
Link
Link 60K AIR LINK Manuel utilisateur
Link
Link LK-F250C11R Manuel utilisateur
Link
Link LK-WRG18L Manuel utilisateur
Link
Link G5 VOODOO PRO Manuel utilisateur
Link
Link LK-TRV18CR Manuel utilisateur
