LINK-MI LM-EP36 Manuel utilisateur

Operating Instructions

H.264 HDMI Extender over IP Extender

With LED, Remote, POE, RS232

Operating Instruction

Operating Instructions

Introduction

This HDMI over IP Extender use the advanced H.264 as the compression

type, which makes it occupy lower bandwidth and transmit over the LAN

more smoothly. It supports 120m over single cat5e/6 cable at point to point,

as well as point to many and many to many over Ethernet switch. The over IP

solution is widely used in various locations, like meeting room, class room,

metro, airport, home, mall advertisement...etc.

1. Features

1). Using H.264 compression encoding, support resolution up to

1080p@60hz

2). Transmit up to 120m over single Cat5e/6 cable, with 1x looping HDMI

output

3). With IR Remote to choose the source, with LED to show the Group ID

4). Comply with TCP/IP protocol, streaming bit rate is up to 15Mbps

5). Support LPCM audio format

6). Smart IP Address Setting: Dynamic Host Configuration Protocol (DHCP)

7). Wide-band IR pass through to control the source (38khz to 56khz)

8). By pass 2 way UART/RS232 (Up to 115200), use remote controller to

select 8 group Baud rate

9). Support one to one, one to many, many to one, many to many modes,

with large cascade

10). Dual power input: 802.3af compliant POE & DC 5V (No need power

supply when connecting with POE Switch)

11). HDCP Compliant

12). Support PC tool control

13). DC 5V 1A power supply

Operating Instructions

2. 1 Specifications

Performance

Protocol H.264 encoder over TCP/IP

Support Video format 480i/480p/576i/576p/720p/1080i/1080p@60HZ

Support Audio format LPCM, Audio sampling rate 48KHZ

Streaming Bit Rate 15Mbps

HDCP Compliant

IR Frequency 38 -56 KHZ

RS232 Baud rate Default 2400bps, total 8 kinds optional

IP setting &Group ID setting

Default IP TX: 192.168.1.11 ; RX: 192.168.1.12

Group ID Group 00 ~ group 63

Request for Switch/Router Support IGMP, support DHCP

Connectors on Transmitter

Input 1xHDMI Female port

Output 1x RJ45 output , 1x HDMI looping output

RS232 Phoenix RS232 port

IR IR TX port (Support 38K-56KHz)

IR Ext port (Support 38KHz)

Connectors on Receiver

Input 1xRJ45 input

Output 1x HDMI Female port looping output

RS232 Phoenix RS232 port

IR IR RX port (Support 38K-56KHz)

IR Ext port (Support 38KHz)

Environmental & Power Requirements

Operating temperature -5 to +35 ℃（+23 to +95℉）

Operating Humidity Range 5 to 90%RH (No Condensation)

Power supply DC 5V 1A

Power consumption Max 3 watt

Physical

Dimension TX: 119x79.5x28mm ; RX: 119x79.5x28mm

Net Weight TX: 0.28KG ; RX:0.28KG

Operating Instructions

2. 1 Supported input resolution

Frequency Resolution

576i

576P

720P

1080P

50Hz

1080i

480i

480P

720P

60Hz/59.94Hz

1080P

30Hz/29.97Hz 1080P

24Hz 1080P

25Hz 1080P

VESA Resolution

Frequency Resolution

576i

576P

720P

1080P

50Hz

1080i

480i

480P

720P

60Hz/59.94Hz

1080P

30Hz/29.97Hz 1080P

24Hz 1080P

25Hz 1080P

Operating Instructions

3. Packing content

1). 1x Transmitter

2). 1x Receiver

3). 1x IR-TX cable

4). 1x IR-RX cable

5). 2X IR Ext Cable

6). 1x Manual

7). 8x screws

8). 4x detachable mounting ears

9). 2x Phoenix plugs for RS232 cable termination

10). 2x Remote controller

11). 2x Power adapter 5V 1A

4. Panel description

1). TX

1)DC5V1Ainput 2) Green indicator of data status

3) Red indicator of power input 4) HDMI output for local display

5)HDMIinput 6)CAT5e/6output

7)IR-TX 8)RS232port

9)IR-Ext 10) LED to show the Group ID

11) Press the button for the previous Group ID

12) Press the button for the next Group ID 13) Reset button

①The green LED will blink once the unit is working.

②The LED indicator will glow bright red once the power supply is

connected.

Operating Instructions

2). RX

1)DC5V1Ainput 2) Green indicator of data status

3) Red indicator of power input 4) HDMI output

5)CAT5e/6input 6)IR-RX

7)RS232port 8)IR-Ext

9) LED to show the Group ID

10) Press the button for the previous GroupID

11) Press the button for the next Group ID 12) Reset button

①The green LED will blink once the unit is working.

②The LED indicator will glow bright red once the power supply is

connected.

3). How to connect the IR Cable

Remote of the source

Remote of the HDMI extender

Operating Instructions

4.1. Panel Drawing

Transmitter

Receiver

Operating Instructions

5. Installation and Configuration

5.1 Setup HDMI TX and RX

When connecting point to point, no need to configure TX and RX,

When connecting point to many, many to point and many to many, please

make sure every TX and RX has unique IP and MAC address, every TX has

unique group ID.

Our this over IP Extender has been assigned unique default MAC address for

every TX and RX, so you don’t have to set the MAC for the units.

You just need to set the IP address and Group ID following bellowing steps.

5.1.1 Setting the IP address

A). DHCP (Dynamic host configuration protocol)

If you are using a Switch that supports DHCP, please enable DHCP so that

the Switch will assign an unique IP for TX and RX, and you don’t need to

change the IP for the units manually.

B). Set the IP via web browser

If you are using a Switch that doesn’t support DHCP, please change the

default IP for TX (192.168.1.11) and RX (192.168.1.12) manually.

A HTTP server is embedded in each TX and RX. You can set up IP address

for HDMI Extender via web browser

The default IP address of the TX is 192.168.1.11, user name: admin,

password: admin

The default IP address of the RX is 192.168.1.12

Operating Instructions

Step 1: Make sure the Transmitter and PC are in the same domain.

Access the Network Setting Control Panel in Windows and locate your

Lan connection. Under Windows 7, this can be done by clicking Start >

Control Panel >Network Sharing center>Change adapter settings >

Properties >Internet Protocol Version4 (TCP/IPv4). Change the IP address fi

eld to 192.168.1.1

(0-255). After that press "OK" to save the configuration.

※The PC and TX/RX should be in the same domain.

※The IP address of PC should be different from the IP address of

TX and RX.

Step 2: Use an Ethernet Cable to connect the PC (or laptop) and the

extender. the power LED for the extender is red and the green status is

blinking.

Step 3: Login in IE: 192.168.1.11 (default IP for TX) or 192.168.1.12(default

IP for RX), You can setup IP address for the TX and RX. TX requires user

name: admin and password: admin

Please set IP address for each TX and each RX, IP: 192.168.1.XX (XX:1-255.

all IP address for TX and RX must be different and can’t be same as the PC’s

address.)

Step 4: After selecting “Use DHCP” or reset the IP Address, click “Submit”

(transmitter) or “update DHCP” (Receiver).

Step 5: Click “Reboot”.

Step 6: Restart the extender after resting the IPAddress.

Operating Instructions

5.1.2 Choose the Group ID and Baud Rate by Remote controller

(When the LED shows “00”, it’s ready to work)

①Press the button, switch to

choose the Group ID or Baud rate.

②Factory reset. Press the button for

3 seconds, the LED will flicker then

turn to “00”, you have successfully

finished the factory reset.

Choose Group ID 00-63

1). Press “+” or “–” to change to the previous or next Group ID.

2). Press the No to change Group ID. For example, if you need change to 01,

press “0”, then press“1”.

Choose the Baud Rate

Press the Button, switch to Baud Rate mode, press “+” or “–” to change the

Baud Rate.

F0 = 2400 (default)

F1 = 4800

F2 = 9600

F3 = 19200

F4 = 28800

F5 = 38400

F6 = 57600

F7 = 115200

3). How to choose the source:

For example, when the connection is:

Source (DVD1) - TX (TX1) - Gigabit Switch – RX (RX1) - TV1

Source (DVD2) - TX (TX2) - Gigabit Switch – RX (RX2) - TV2

Source (DVD3) - TX (TX3) - Gigabit Switch – RX (RX3) - TV3

The group ID of transmitters is:

TX1 (01)

TX2 (02)

TX3 (03)

If you need display Source on TV1, then just set Group ID of RX1 same as

TX1: 01(see below picture).

TX1 RX1

Table des matières

Autres manuels LINK-MI Extenseur

LINK-MI

LINK-MI LM-WE02 Manuel utilisateur

LINK-MI

LINK-MI LM-THF106D Manuel utilisateur

LINK-MI

LINK-MI EX33 Manuel utilisateur

LINK-MI

LINK-MI LM-THF109D Manuel utilisateur

LINK-MI

LINK-MI LM-200H Manuel utilisateur

LINK-MI

LINK-MI LM-100H Manuel utilisateur

LINK-MI

LINK-MI LM-K100H Manuel utilisateur

LINK-MI

LINK-MI LM-THF123H Manuel utilisateur

LINK-MI

LINK-MI LM-THF107D Manuel utilisateur

LINK-MI

LINK-MI LM-DT206FKM Manuel utilisateur

LINK-MI

LINK-MI LM-THF123HKM Manuel utilisateur

LINK-MI

LINK-MI LM-DEX60 Manuel utilisateur

LINK-MI

LINK-MI LM-CX100IR Manuel utilisateur

LINK-MI

LINK-MI LM-EX100-4K2K Manuel utilisateur

LINK-MI

LINK-MI LM-HT201DKM Manuel utilisateur

LINK-MI

LINK-MI LM-HT201D Manuel utilisateur

LINK-MI

LINK-MI LM-HE60-POE Manuel utilisateur

LINK-MI

LINK-MI LM-WHS400 Manuel utilisateur

LINK-MI

LINK-MI LM-EW53 Manuel utilisateur

LINK-MI

LINK-MI LM-WX700 Manuel utilisateur

LINK-MI

LINK-MI LM-HEX01 Manuel utilisateur

LINK-MI

LINK-MI LM-HE150 Manuel utilisateur

LINK-MI

LINK-MI LM-THF108 Manuel utilisateur

LINK-MI

LINK-MI LM-HT208 Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur