Linear Technology 813 Instructions d'utilisation et d'entretien

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 813

HIGH VOLTAGE MICROPOWER VOLTAGE REGULATOR

LT3013

DESCRIPTION

Demonstration circuit 813 is a high voltage micro-

power voltage regulator using the LT3013 low drop-

out linear regulator, which comes in a low-profile 12-

pin DFN package. DC813 has an input voltage range

from 3V to 80V, an output voltage range between

1.24V and 60V, and is capable of delivering 250 mA

max. The DC supply current is typically only 1 uA in

shutdown. DC813 is installed with ceramic capaci-

tors, because of its ability to maintain stability with

ceramic output capacitors. Due to its high input volt-

age range, the DC813 voltage regulator is ideally

suited for automotive and industrial applications.

Design files for this circuit board are available. Call

the LTC factory.

LTC is a trademark of Linear Technology Corporation

QUICK START PROCEDURE

DC813 is easy to set up to evaluate the performance

of the LT3013. For proper measurement equipment

configuration, set up the circuit according to the dia-

gram in Figure 1.

Please follow the procedure outlined below for proper

operation.

1. Before proceeding to test, insert a shunt into

the OFF position of jumper JP1, and insert a

shunt into jumper JP2, the 3.3V option.

2. Apply 5V across Vin (to GND). Insert the

jumper JP1 shunt into the ON position. Draw

1 mA of load current. Measure Vout; it should

be 3.3V +/- 2.5% (3.21V to 3.39V).

3. Vary the input voltage from 5V to 80V and the

load current from no load to 250 mA. Vout

should measure 3.3V +/- 5% (3.13V to

3.47V).

Note: Be aware of the power dissipated by the

LT3013, due to its high input voltage capabil-

ity. Consequently, take care to stay under the

maximum junction temperature, 125 deg.C,

when operating the LT3013.

4. Insert the jumper JP1 shunt into the OFF posi-

tion and move the shunt in jumper JP2 into

the 5V output voltage option, and repeat the

test. Re-insert jumper JP1 shunt into the ON

position. Just as in the 3.3 Vout test, the 5V

output voltage should read Vout +/- 2.5% tol-

erance under static line and load conditions,

and +/- 5% tolerance under dynamic line and

load conditions.

5. When finished evaluating, insert jumper JP1

shunt into the OFF position.

Warning - If long leads are used to power the demo circuit, the input voltage at the part could “ring”. This ring-

ing could affect the operation of the circuit or even exceed the maximum voltage rating of the IC. To eliminate

this, insert a small aluminum electrolytic capacitor (for instance, a Sanyo cap., part # 100CV10BS) on the pads

between the input power and return terminals on the bottom of the demo board. The (greater) ESR of the alu-

minum electrolytic capacitor will dampen the (possible) ringing voltage due to the use of long input leads. On a

normal, typical PCB, with short traces, the capacitor is not needed.

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 813

HIGH VOLTAGE MICROPOWER VOLTAGE REGULATOR

Figure 2. Measuring Input or Output Voltage Ripple

Figure1. Proper Measurement Equipment Setup

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 813

HIGH VOLTAGE MICROPOWER VOLTAGE REGULATOR

Autres manuels Linear Technology Contrôleurs

Linear Technology

Linear Technology DC2147A Guide de configuration rapide

Linear Technology

Linear Technology LTM4636 Manuel utilisateur

Linear Technology

Linear Technology DC1663A Guide de configuration rapide

Linear Technology

Linear Technology LT8610A Guide de configuration rapide

Linear Technology

Linear Technology LT3790 Guide de configuration rapide

Linear Technology

Linear Technology LTC4080 Manuel utilisateur

Linear Technology

Linear Technology LT3755 Manuel utilisateur

Linear Technology

Linear Technology DC1936A Guide de configuration rapide

Linear Technology

Linear Technology DC1865A Guide de configuration rapide

Linear Technology

Linear Technology LTC2920-1CS5 Manuel utilisateur

Linear Technology

Linear Technology LTM4650EY-1 Guide de configuration rapide

Linear Technology

Linear Technology LTC4365 Guide de configuration rapide

Linear Technology

Linear Technology mModule LTM8023 Guide de configuration rapide

Linear Technology

Linear Technology LTC4232 Guide de configuration rapide

Linear Technology

Linear Technology LTC7138 Guide de configuration rapide

Linear Technology

Linear Technology DEMONSTRATION CIRCUIT 886 Manuel utilisateur

Linear Technology

Linear Technology DC1817B Guide de configuration rapide

Linear Technology

Linear Technology LT3507 Guide de configuration rapide

Linear Technology

Linear Technology LTC3212 Manuel utilisateur

Linear Technology

Linear Technology LTC4266A Manuel utilisateur

Linear Technology

Linear Technology LTC3542 Manuel utilisateur

Linear Technology

Linear Technology LTM4676EY Manuel utilisateur

Linear Technology

Linear Technology LTM4624EY Manuel utilisateur

Linear Technology

Linear Technology LTC3875EUJ Guide de configuration rapide

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur