Linddana TP Series Manuel utilisateur

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

User instructions

Spare parts catalogue

for TP 230 wood chipper from

the Forest series

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

1Introduction

Congratulations on your new TP wood chipper.

Linddana manufactures top-quality TP wood chippers using the most modern production

technology, including laser-cutting, CNC technology and robot technology, at light, open

production premises.

For safety reasons and in order to gain maximum benefit from your wood chipper, it is essential

to read through the user instructions before using the machine for the first time.

The user instructions explain about safety, use and maintenance, so that work with the wood

chipper can proceed safely and profitably.

This manual has been translated from Danish.

Linddana A/S

Jørgen Due Jensen, director

Your dealer is always available to provide spare parts, useful advice and guidance.

Dealer’s stamp

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

2EU declaration of conformity.

Manufacturer:

LINDDANA A/S, Ølholm Bygade 70, Ølholm, 7160 Tørring, Denmark

hereby declares that

Wood chipper: ________________________________________________

is in concordance with the provisions of the Machine Directive (Directive 06/42/EF) and with the

national legislation which translates this directive;

is in concordance with the following other EC Directives:

2000/14/EC

Furthermore it is stated that

EN 13525 (harmonised standard), has been used.

Title: Managing director

Name: Jørgen Due Jensen

Ølholm, 02 november 2015

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

3Table of contents

1Introduction .................................................................................................... 2

2EU declaration of conformity........................................................................... 3

3Table of contents............................................................................................. 4

4Use .................................................................................................................. 5

5Assembly instructions ..................................................................................... 6

5.1 Before initial operation........................................................................................................6

5.2 Coupling instructions ...........................................................................................................7

6Safety instructions........................................................................................... 8

6.1 Safety regulations ................................................................................................................8

6.2 Pictograms used.................................................................................................................10

6.3 Noise level..........................................................................................................................11

6.4 Environmental instructions ...............................................................................................11

7Operation of the machine ............................................................................. 12

7.1 Table 1 Rotation speed settings for feed rollers ...............................................................13

8Maintenance ................................................................................................. 13

8.1 Maintenance schedule.......................................................................................................13

8.2 Lubrication and oil .............................................................................................................14

8.3 Replacing wearing parts.....................................................................................................15

8.4 Sharpening knives ..............................................................................................................23

9User Instructions for TP PILOT 01 .................................................................. 24

9.1 General operation..............................................................................................................24

9.2 Programming .....................................................................................................................26

9.3 Installation .........................................................................................................................30

9.4 Technical data ....................................................................................................................31

10 Troubleshooting for TP 230 wood chipper.................................................. 32

11 Warranty commitment – wood chipper ..................................................... 33

12 Technical data – wood chipper................................................................... 35

13 Hydraulic diagrams .................................................................................... 36

14 Accessories ................................................................................................ 37

15 Spare parts catalogue................................................................................. 37

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

4Use

The TP 230 wood chipper has been specially designed for stationary wood chipping, in the form of

branches, bushes and wood waste from hedgerows, parks, trees along roads, etc.

Consequently, the machine must not be used for materials containing stone, metal or other

foreign matter. Such foreign matter can, at best, make the knives blunt, and, at worst, break the

machine. Knives and anvils can get broken if stone or metal objects get between them.

The machine must not be used for chipping wood that may contain nails, screws, reinforcement,

etc.

When feeding in branches, you must stand to the side of the feed funnel (See Figure 1).

Branches can whip about when the feed rollers catch them.

When feeding in logs, push these in from the rear (See Figure 2).

Figure 1 Feeding in branches Figure 2 Feeding in logs

Remember to keep knives and anvils sharp; this facilitates feeding and provides better chip

quality. It also reduces fuel consumption.

The machine must be inspected daily, i.e. the rotor housing must be opened and feed mechanism,

rotor, knives, anvils, etc. checked. This protects against unexpected stoppages and ensures a

longer service life for the machine.

The tractor to which the wood chipper is attached must always be secured in a stationary position

during work.

The machine must not:

·be used for any material other than wood

·be used to push over trees, stumps, etc.

Equipment such as choke chains, axes, power saws must not be placed/transported in the feed

funnel.

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

5Assembly instructions

5.1 Before initial operation

The machine is equipped with a lifting eyelet that can be used when the machine is lifted by crane

or other hoisting device (hoisting). (See Figure 3). The machine can also be lifted using a forklift

truck, but great care must be exercised, as the machine may tip over (See Figure 4).

Figure 3 Lifting eyelet on the machine

Figure 4 Lifting using a forklift truck

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

Keep user instructions for the PTO shaft together with these user instructions in the special

manual box on the machine.

Before start-up you must check that the wood chipper is free of foreign matter. Loosen the bolts

that hold the upper and lower rotor housing together. Lift up the top part of the rotor housing

until the ejector tube rests in position and turn the rotor several revolutions by hand. Remove any

foreign matter.

Check whether the knives are the correct distance (1 mm) from the anvil. The knife gap is set to

10 mm at the factory. Check whether the knives run free of the anvils.

Lift the top part of the rotor housing into place again and replace the bolts.

Check that all bolts, nuts and screws are properly tightened.

Remember to lubricate all lubrication points (See maintenance schedule on page 13).

Take old hydraulic and motor oil and used oil and air filters to an approved receiving station.

5.2 Coupling instructions

The machine is designed for coupling to a tractor’s three-point hitch.

The factory can supply the machine with a PTO shaft equipped with either 1 3/8" - 6 splines or 1

3/8" - 21 splines

A PTO shaft with 1 3/8" - 6 splines is used on the tractor at 540 rpm. At 1000 rpm, a PTO shaft

with 1 3/8" - 21 splines must be used for some types of tractor.

The PTO shaft must be fitted with free-wheel on the machine side.

Linddana uses Walterscheid 2400 with free-wheel, which accompanies the machine.

The length of the PTO shaft must be adjusted for the tractor according to the instructions from

the supplier of the PTO shaft. See attached user instructions for PTO shaft.

The machine must be standing on firm, level ground when in use. The tractor must be hooked up

to the three-point hitch. The tractor must always be secured in a stationary position.

When starting up the machine: Coupling must be undertaken while idling or with as low a motor

speed as possible, in order to avoid overloading the PTO shaft, gearbox, tractor and wood chipper.

Figur 5

Position of ejector tube

when opening rotor

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

6Safety instructions

6.1 Safety regulations

·Use hearing protection, safety goggles or equivalent eye protection, close-fitting

protective clothing and safety shoes.

·When working along roads, it is a good idea to wear a reflective vest in order to be more

visible to other road users. Road signs must comply with applicable traffic regulations.

·Minimum permitted age for operating the machine is 18 years, but 16 years when training

under the supervision of an adult.

·Keep all body parts away from the feed funnel and the machine’s moving parts during

operation.

·Always stand to the side of the feed funnel when filling the machine. Always be aware of

the nature of the ground around the machine. Falling over close to the machine can be

dangerous!

·Before starting up, check that the machine’s safety devices

are functioning correctly. This applies in particular to the

operating guard’s stop and return function.

·Never use the machine in enclosed or poorly ventilated

spaces due to danger of carbon monoxide poisoning

·The top part of the machine must not be opened unless

the rotor disc is completely stationary and the tractor’s

motor has stopped.

·Always stop the machine and tractor for any inspections,

servicing and repair work.

·Tractor-mounted machinery must be lowered to the

ground before performing any servicing or repair work

·Always remove ignition keys from the machine and/or

tractor when leaving the machine.

·Following maintenance and repair work, the machine may

only be started once all bolts have been tightened and all safety devices fitted.

·Three-point hitch-mounted machines must be coupled to the tractor’s three-point hitch

before use.

·The machine’s maximum motor speed (1000 rpm) must not be exceeded.

·The PTO shaft shielding and cover must always be intact. Safety chains on the PTO shaft

must be securely fitted.

·The length of the PTO shaft must be adjusted for the tractor according to the instructions

from the supplier of the PTO shaft.

·The ejector tube must not point towards people or areas where people are walking.

·IN THE EVENT OF DANGER: PUT THE OPERATING GUARD IN NEUTRAL

(See Figure 8)

Figur 6 Twocolored shaftend

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

·During operation set the machine’s height to at least 600 mm above the ground (Figure 7).

Figure 7 Minimum height above the ground

·During transport or when dismantled, place the PTO shaft in the machine’s shaft holder.

·In case of transport on roads the ejector tube is turned so it is placed appropriately within

the width of the machine and then it is fixed securely.For transport on public roads, official

regulations must be obeyed.

·The machine is equipped with a tilting funnel; this must be tipped up and secured with

split pins during transport.

·When cleaning small chips from the base of the funnel, THE FEED ROLLERS MUST BE

STOPPED.

·A brush or similar item must be used for cleaning. Never touch the inside of the funnel

when the machine is in operation.

Linddana A/S . Ølholm Bygade 70 . DK-7160 Tørring . T +45 75 80 52 00 . tp@linddana.com . www.linddana.com

6.2 Pictograms used

Warning: Objects thrown!

Safety distance 20m!

Warning: Rotating knives!

Wait for rotor to stop!

Warning: Rotating rollers!

Warning: Rotating belts! Warning: Danger of retraction!

Do not touch the hopper!

Warning: Danger of retraction!

Do not step on the hopper!

Read the manual before use! Hearing protector and eye

protection prescribed!

Lifting point for crane!

Warning: Max 1000 rpm, anti-

clockwise direction of

rotation!

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Linddana Chipper

Linddana

Linddana TP 160 Manuel de l'installateur

Manuels Chipper populaires d'autres marques

Craftsman

Craftsman 79964 Manuel utilisateur

Frontier

Frontier WC1208 Manuel utilisateur

Viking

Viking GE 150 Manuel utilisateur

Victory

Victory WC-8H Manuel utilisateur

GTM Professional

GTM Professional GTS 1300 Manuel utilisateur

Yardbeast

Yardbeast YB3514 Manuel utilisateur

Patriot

Patriot Electric Motors Manuel utilisateur

Echo

Echo CH5540 Manuel utilisateur

DOSKO

DOSKO 13-21T-13H Manuel utilisateur

Craftsman

Craftsman 486.24516 Manuel utilisateur

Garland

Garland 1480 TQG Manuel utilisateur

Vermeer

Vermeer BC160XL Guide rapide

Value Leader

Value Leader z9400 Mode d’emploi

Timberwolf

Timberwolf TW 230HB Manuel utilisateur

Salsco

Salsco 600PTO Manuel du produit

Cub Cadet

Cub Cadet 24A-424M710 Manuel utilisateur

Champion

Champion 91050 Manuel

Kellfri

Kellfri 13-WC17H2 Manuel utilisateur