Lightolier END FEED AND FLOATING CANOPY MOUNTING KIT Instructions d'utilisation

READ AND UNDERSTAND ALL TRACK, CONNECTOR, FEED-IN-KITS, AND ACCESSORY

INSTRUCTION SHEETS BEFORE INSTALLING ANY PROSPEC®TRACK ITEM.

This fixture is intended for installation in accordance with the National Electrical Code and local or Federal

code specifications. To assure full compliance with codes and regulations, check with your local electrical

inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

LIGHTOLIER a GENLYTE company.

631 Airport Road, Fall River, MA 02720

INSTRUCTION SHEET NO.

IS:26060

0597 Page 1 of 2

END FEED AND FLOATING CANOPY MOUNTING KIT - FLUSH AND STANDOFF VERSIONS

FOR USE WITH PROSPEC®SURFACE MOUNT TRACK SYSTEMS ONLY

END FEED MOUNTING INSTRUCTIONS

(Flush 26060WH, BK and Standoff 26061WH, BK)

Mounting the CANOPY at the end of FEED TRACK or directly above

a FEED CONNECTOR.

1. Mark CENTER LINE for TRACK through CENTER LINE of OUT-

LET BOX.

2. NOTE: The CANOPY mounts to a 3 or 4” OCTAGON OUTLET

BOX. The MOUNTING HOLES of the OUTLET BOX should be at

45° to the longitudinal axis of the TRACK. (Fig. 1)

3. Remove the KNOCK OUT PLATE from the FEED TRACK or

CONNECTOR (retain the SCREW). (Fig. 2)

4. Prepare TAB on the PLATE ASSEMBLY as follows:

• FEED TRACK: DO NOT BREAK ANY TAB. (Fig. 2)

• POWER EXTENSION, IN-LINE, “T”, AND “X” CONNECTORS:

BREAK THE 90° TAB OFF THE PLATE ASSEMBLY. (Fig. 3)

• “L” CONNECTOR: BREAK THE 90° TAB AND THE STRAIGHT

TAB FROM THE PLATE ASSEMBLY. (Fig. 4)

5. Attach the PLATE ASSEMBLY onto the FEED TRACK or

CONNECTOR using the SCREW. (Fig. 2 &3)

6. Mount the TRACK to the ceiling (see instruction sheet

IS:26000 provided with the TRACK) passing the wires through

the center of the PLATE ASSEMBLY.

7. Rotate the PLATE ASSEMBLY until the SLOTS are in-line with

the MOUNTING HOLES on the J-BOX.

8. Secure the PLATE ASSEMBLY to the J-BOX using the THIN

HEAD SCREWS. (Fig. 5)

9. Attach the GROUND WIRE on the CANOPY PLATE to the

GROUND LEAD or GROUND TERMINAL in the J-BOX. (Fig. 5)

10. WHEN USING THE FLUSH CANOPY 26060WH/BK.

Slide the CANOPY PLATE between the CONNECTOR and

CROSS BAR on the PLATE ASSEMBLY. For added security of

CANOPY PLATE: Drill a hole in CANOPY PLATE and secure to

ceiling with a screw.

11. WHEN USING THE STANDOFF CANOPY 26061WH/BK

Slide the CANOPY PLATE between the CROSS BAR and NUT

on the PLATE ASSEMBLY. Rotate the NUT to secure the

CANOPY PLATE against the ceiling. (Fig. 8)

NOTE: THE CROSS BAR MUST COVER THE SLOT IN

THE CANOPY PLATE AFTER ASSEMBLY.

12. Follow the instructions for wiring on the instruction sheet

included with the “FEED TRACK” or “CONNECTOR”.

CAUTION: TURN OFF POWER AT FUSE BOX BEFORE

INSTALLING THE CANOPY KIT

POWER EXTENSION

CONNECTOR

PLATE

ASSEMBLY

SCREW

90 ° TA B

KNOCK OUT

PLATE

FIG. 2

FIG. 3

PLATE

ASSEMBLY

SCREW

KNOCK OUT

PLATE

FEED TRACK

FIG. 4

STRAIGHT

TAB

PLATE

ASSEMBLY

90 ° TA B

KNOCK OUT

PLATE

“L” CONNECTOR

CANOPY

PLATE

GROUND

WIRE

THIN HEAD

SCREW

J-BOX

FIG. 5

CROSS BAR

45 °

TRACK UNIT LONGITUDINAL

TRACK

OUTLET BOX

MOUNTING HOLE

FIG. 1

READ AND UNDERSTAND ALL TRACK, CONNECTOR, FEED-IN-KITS, AND ACCESSORY

INSTRUCTION SHEETS BEFORE INSTALLING ANY PROSPEC®TRACK ITEM.

This fixture is intended for installation in accordance with the National Electrical Code and local or Federal

code specifications. To assure full compliance with codes and regulations, check with your local electrical

inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

LIGHTOLIER a GENLYTE company.

631 Airport Road, Fall River, MA 02720

INSTRUCTION SHEET NO.

IS:26060

0597 Page 2 of 2

FLOATING FEED MOUNTING INSTRUCTIONS

(Flush 26060WH, BK and Standoff 26061WH, BK)

Mounting the CANOPY at some distance away from the end of the

FEED TRACK or FEED CONNECTOR.

NOTE: Hardware is supplied to mount the CANOPY a maximum

of 4 feet from the FEED CONNECTOR. DO NOT EXCEED

THIS DISTANCE.

1. Mark CENTER LINE of TRACK through CENTER LINE of OUT-

LET BOX.

2. NOTE: The CANOPY mounts to a 3 or 4” OCTAGON OUTLET

BOX. The MOUNTING HOLES of the OUTLET BOX should be at

45° to the longitudinal axis of the TRACK. (Fig. 1)

3. Break the BARRIER off the FEED CONNECTOR or FEED TRACK.

(Fig. 6)

4. Remove the DEAD END from the TRACK and retain.

5. Assembly the “U” BRACKET onto the PLATE ASSEMBLY using

the FLAT HEAD SCREW. (Fig. 6)

6. Run the feed wires along the top of the TRACK and into the

FEED CONNECTOR or FEED TRACK. (2 HOTS, 2 NEUTRALS,

AND GROUND; MAXIMUM)

7. NOTE: USE 12 GA. COPPER THHN WIRE INCLUDING

GROUND. IF STRANDED 12 GA WIRE IS USED THE ENDS

MUST BE TINNED.

8. Cut the WIRE COVER to the desired length.

9. Slide the WIRE COVER (over the wires) and PLATE ASSEMBLY

into the TRACK. NOTE THE POSITION OF THE 90° TAB IN

RELATION TO THE FEED-IN POINT. Pass the wires

through the center hole of the PLATE ASSEMBLY.

10. Secure the PLATE ASSEMBLY to the TRACK by tightening the

SCREW. THE WIRE COVER MUST COVER THE ENTIRE

LENGTH OF WIRES ON TOPS OF THE TRACK.

11. Mount the TRACK to the ceiling (see instruction sheet 26000

provided with the track or IS:26478). Positioning the PLATE

ASSEMBLY over the J-BOX.

12. Splice the wires from the track to the wires in the J-BOX.

BLACK TO BLACK, WHITE TO WHITE, AND GROUND TO

GROUND.

13. Rotate the PLATE ASSEMBLY until the SLOTS are in-line with

the MOUNTING HOLES on the J-BOX.

14. Secure the PLATE ASSEMBLY to the J-BOX using the THIN

HEAD SCREWS. (Fig. 7)

15. Attach the GROUND WIRE on the CANOPY PLATE to the

GROUND LEAD or GROUND TERMINAL in the J-BOX. (Fig. 7)

16. WHEN USING THE FLUSH CANOPY 26060WH/BK.

Slide the CANOPY PLATE between the TRACK and CROSS

BAR on the PLATE ASSEMBLY. For added security of CANOPY

PLATE: Drill a hole in CANOPY PLATE and secure to ceiling

with a screw.

17. WHEN USING THE STANDOFF CANOPY 26061WH/BK.

Slide the CANOPY PLATE between the CROSS BAR and NUT

on the PLATE ASSEMBLY. Rotate the NUT to secure the

CANOPY PLATE against the ceiling. (Fig. 8)

18. NOTE: THE CROSSBAR MUST COVER THE SLOT IN

THE CANOPY PLATE AFTER ASSEMBLY.

19. Follow the instructions for wiring on the instruction sheets

included with the the “FEED TRACK” or “CONNECTOR”.

20. Assembly the DEAD END into the end of the TRACK.

FIG. 6

BARRIER DEAD

END

U BRACKET

90 ° TA B

FLAT HEAD

SCREW

PLATE

ASSEMBLY

WIRE COVER

TRACK UNIT

FEED CONNECTOR

FEED IN POINT

U BRACKET

FIG. 8

TRACK UNIT

J BOX CANOPY

PLATE

POWER EXTENSION

CONNECTOR

NUT

FIG. 7

CANOPY PLATE

J-BOX

PLATE

ASSEMBLY

WIRE COVER

POWER EXTENSION

CONNECTOR

TRACK UNIT

THIN HEAD

SCREW

CROSS BAR

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Lightolier Équipement d'éclairage

Lightolier

Lightolier Lytespan 8277 Manuel utilisateur

Lightolier

Lightolier Calculite Matrix 4X9LW Manuel utilisateur

Lightolier

Lightolier FBP Low Profile Fluorescent Emergency Ballast... Manuel utilisateur

Lightolier

Lightolier Lighting Systems IS-A1 Manuel utilisateur

Lightolier

Lightolier Lighting Systems CD7-8 Manuel utilisateur

Lightolier

Lightolier Lighting Systems EG2-5 Manuel utilisateur

Lightolier

Lightolier Lytecel 6 LIA6GPNXR132 Manuel utilisateur

Lightolier

Lightolier Lytespan DR2C Manuel utilisateur

Lightolier

Lightolier Lighting Systems Baselyte-BSL13 Manuel utilisateur

Lightolier

Lightolier Calculite A-E Manuel utilisateur

Lightolier

Lightolier 1050DSQ Manuel utilisateur

Lightolier

Lightolier LP-2 Manuel utilisateur

Lightolier

Lightolier Calculite C6P38MHA Manuel utilisateur

Lightolier

Lightolier LSBW-6 Manuel utilisateur

Lightolier

Lightolier Lytespan 9220 Manuel utilisateur

Lightolier

Lightolier Baselyte-BSL20 Manuel utilisateur

Lightolier

Lightolier Calculite ProSpec PB4A7050 Manuel utilisateur

Lightolier

Lightolier Mini-Beam Mini-Beam Luminaires Manuel utilisateur

Lightolier

Lightolier Lytespan 83ED17RWF Manuel utilisateur

Lightolier

Lightolier Calculite C4P20MHGA Manuel utilisateur

Lightolier

Lightolier Lytespan 6310 Manuel utilisateur

Lightolier

Lightolier LP-15 Manuel utilisateur

Lightolier

Lightolier Lytespan 23S70T6 Manuel utilisateur

Lightolier

Lightolier Baselyte-BSL19 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur