Light4CE LEDForce 18 RGBW Manuel utilisateur
1
2
User manual
LEDForce 18 RGBW
1.Safety instructions
- Every person involved with the installation, operation and maintenance of this device has to :
bequalied
follow the instructions of this manual
- CAUTION! Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric
shock when touching the wires!
- This device has left our premises in absolutely perfect condition. In order to maintain this condition and
to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and
warning notes written in this user manual.
- Important: Damages caused by the disregard of this user manual are not subject to warranty.
The distributor will not accept liability for any resulting defects or problems.
- Keep away from heaters and other heating sources!
-Ifthedevicehasbeenexposedtodrastictemperatureuctuation(e.g.aftertransportation),donotswitchit
on immediately. The arising condensation water might damage your device. Leave the device switched off
until it has reached room temperature.
- Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and
the power-cord from time to time.
-Iftheexternalexiblecableorcordofthisluminaireisdamaged,itshallbeexclusivelyreplacedby
themanufacturerorhisserviceagentorasimilarqualiedpersoninordertoavoidahazard.
- shields, lenses or ultraviolet screens shall be changed if they have become visibly damaged to such
an extent that their effectiveness is impaired, for example by cracks or deep scratches.
- Never let the power-cord come into contact with other cables! Handle the power-cord and all connections
with the mains with particular caution!
- Make sure that the available voltage is not higher than stated in this manual.
- Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle
the power-cord by the plug. Never pull out the plug by tugging the power-cord.
- During the initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective.
- DANGER OF BURNING! Never touch the device during the operation! The housing heats up to the housing
temperature.
- Don't switch the device on and off in short intervals as this would reduce the lamp's life.
- HEALTH HAZARD! Never look directly into the light source, as sensitive persons may suffer an epileptic
shock(especiallymeantforepileptics)!
- Always disconnect from the mains, when the device is not in user or before cleaning it.
-Pleasenotethatdamagescausedbymanualmodicationsonthedeviceorunauthorizedoperation
byunqualiedpersonsarenotsubjecttowarranty.
- Keep away children and amateurs from the device!
- There are no serviceable parts inside the device. Maintenance and service operations are only to be
carriedoutbyauthorizeddealers.
2.Operation Instruction
1)ThesystemhasDMXonlinemodeandstand-alonemode.DMXonlinemodecanlinkupeachother
andiscontrolledbyDMXcontroller.Stand-alonehassomefunctions,suchasdimmer,changeprogram,
music active and so on.
2)WhenunderDMXmodeorMaster/slavemode,thesignalispresent.TheslaveLEDwillblinkfast.
The address will blink without signal.
3)IftheslavelinksupthemasterandalsoconnectswithDMXcontroller,themastercanidentify
automatically the data and also turn off the function of sending data from master. Under this mode,
theledislightless.TheslavereceivesthesignalfromDMXcontroller.
3
I.Display description:
II.Display instruction
Mode: show running mode
VALUE: the display shows address, speed and dimmer value.
SLAVE:theslavesendstoindicate
MASTER:themastersendstoindicate
III. Control buttons
UP:selectDMXaddressandspeedclockwisedirection.
Down:selectDMXaddressandspeedcounter-clockwisedirection.
Mode:selectLEDmode,thedetailsasgureI.
The device can save the current state under power off and enter automatically the last program when re-turn
on.
Figure I:
Mode Display Operation
Display On all the
time
0001 The display is on all the time
Auto turnoff 0002 The display can turn off automatically after running 10s.
Any button is no function under this mode. It can display by
pressing any button 3s.
DMX
mode
4 CHannel
Mode
1***,***=DMX
address
CH1=R dimmer, CH2=G dimmer, CH3=B dimmer, CH4=W
dimmer
6 CHannel
Mode
2***,***=DMX
address
CH1=R dimmer, CH2=G dimmer, CH3=B dimmer, CH4=W
dimmer, CH5=Total dimmer, CH1=Total strobe
Slave
mode
3***, ***=Ran-
dom
The slave mode can be worked under the manual mode and
sound control mode.
The unit can not run any operations, and only receives and
corresponds to the master mode. All slave run modes are
coresponding to the master modes.
Manual
Mode
Preset color
mode
40**, **=preset
color mode
Selectthebuilt-incolorsfrom20patterns
Preset
program
50**, **=preset
program mode
Change9presetprogramviaUp/Downkey
Dimmer
speed
mode
60**, **=speed
value
Changetheprogramspeed(value16isfastestspeed)
under50**viaUp/Downkey
R adjust
luminance
***, ***=value AdjustluminancevalueviaUp/Downkey.(0-255)
G adjust
luminance
***, ***=value AdjustluminancevalueviaUp/Downkey.(0-255)
B adjust
luminance
***, ***=value AdjustluminancevalueviaUp/Downkey.(0-255)
W adjust
luminance
E***, ***=value AdjustluminancevalueviaUp/Downkey.(0-255)
Music Mode 70**, **=Opera-
ting mode
1. Display showing 7001-7009 denotes that the unit operates
one of the 9 program respectively.
2. Display showing 7ALL denotes that 9 programs respecti-
vely run four times.
4
3.Technical specications
Inputvoltagerange:90-260V,50/60Hz
Powerconsumption:95W/107VA(powerfactor=0.88)
LEDdevice:18x5WattQuadColorRGBWLEDs
Expected life time: 50,000 hours
BeamAngle:25°,(10°optionalkitavailable)
Operationalmodes:SoundActive,Macro,Auto,DMX
ControlprotocolDMX512
DMXmodes:2
Control channels: 4,6
Settingandaddressing:LEDcontroldisplay
DMXIN/OUT:5-pinXLR
Dimensions:(LxWxH)292x216x216mm/11,5”x8,5”x8,5”(withouthangingbracket)
Weight : 4.9 kg
Version:1.1
April 19, 2010
Specications are subject to change without specication
Table des matières
Autres manuels Light4CE Projecteur
Manuels Projecteur populaires d'autres marques
VIZULO
VIZULO Micro Martin Guide de l'utilisateur
EuroLite
EuroLite LED IP FL-100 SMD Manuel utilisateur
Cooper Wheelock
Cooper Wheelock XB12 Manuel utilisateur
Allen + Roth
Allen + Roth 17624-000 Manuel utilisateur
ADJ
ADJ 4 STAGE PAK Manuel utilisateur
Cooper Lighting
Cooper Lighting EGL91SW233 Manuel utilisateur
