Light Emotion DERBY2 Mode d’emploi

www.lightemotion.com.au

DERBY2

2-in-1 Laser and Derby Effect.

User’s instruction manual

This manual contains important information about the safe installation and use of this product

Please read this instruction manual carefully before installing or operating

Please keep these instructions in a safe place for future reference

Contents

1. Safety Instructions 2

2. Installation 3

3. Features 3

4. Remote Control Operation 4

5. Menu Operation 5

6. DMX Table 5

7. DMX Address Setting 6

8. DMX Terminator 7

9. Rigging 8

10. Cleaning and Maintenance 8

11. Technical Data 8

12. Warranty 9

Introduction

Thank you for the purchase of your DERBY2 2-in-1 Laser and Derby effect by Light Emotion.

We are confident you will be satisfied with your purchase and enjoy many years of use from

this Professional Light Emotion product. Please read these instructions carefully to ensure the

product is well look after and used correctly to avoid any potential problems.

Please note that as part of our ongoing commitment to continuous improvement and product

development, the specifications in this manual are subject to change without notice. Whilst

every care has been taken in the preparation of this manual we reserve the right to change

specifications in the course of product improvement.

What is in the box:

- 1 x DERBY2 Lighting Effect

- 1 x Power Cable

- 1 x IR remote control

- 1 set laser key and remote plug

- This user manual

1. Safety Instructions:

Please read these instructions carefully. It includes important information about the installation

usage and maintenance of this product.

- Please keep this User Manual for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

- Always make sure that you are connecting to the proper voltage and that the line voltage you

are connecting to is not higher than that stated on the sticker of the fixture.

- This product is intended for indoor use only. To prevent risk of fire or shock, do not expose

fixture to rain or moisture.

- Make sure there are no flammable materials close to the unit while operating.

- The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surface. Be sure that no ventilation slots are blocked.

- Always disconnect from power source before servicing.

- Secure fixture to stands, trussing and the like using a safety chain.

- Maximum ambient temperature is 40˚C. Do not operate fixture at temperatures higher than

this.

- In the event of serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center.

- Make sure power cord is never crimped or damaged.

- Never disconnect power cord by pulling or tugging on the cord.

- Never carry the fixture directly from the cord. Carry by holding the base of the unit, and only

move when unit is upright.

- Avoid direct eye exposure to the light source while it is on.

2. Installation:

Caution: For safe mounting of this product, please read the following carefully.

- Use a suitable clamp to attach to lighting stand, trussing or bar, together with safety chain.

- When mounting the product, do not stand directly underneath the product

- Always use a safety chain when mounting the product on stands, trussing or bars. Make sure

the breaking strain rating of the chain is at least 10 times the weight of the product.

- Make sure there is adequate ventilation around the product.

- This product is designed to be mounted and used in the upright position. Using in any other

orientation could cause damage to the internal motors for both the LED and laser. When

transporting, it is also best to keep the product upright.

- Never look directly into the LED light sources of the product.

- For indoor use only – do not use outdoors.

- To avoid electrical shock, keep away from rain and moisture.

- Keep out of reach of children.

3. Features

This product is designed as an LED lighting effect and is only intended to be used as an LED

lighting effect for entertainment and display applications. Due to our ongoing commitment to

constantly reviewing and improving products, features and specifications are subject to change

without prior notice.

- LEDs: 1 x 30w 4-in-1 RGBW LED with average 50000 hours lifespan

- Laser: 150mW red laser diode 650nm, 50mW green laser diode 532nm

- Lenses: 48

- Control: DMX, Sound Activation, Stand Alone, Master/Slave

- Key switch and interlock on rear panel

- DMX Channels: 13

- Audio sensitivity knob

- 3 pin XLR male and female DMX sockets

- Functions: Combined laser and derby effect, Individually controllable effects, Strobing.

- Built in programs using laser and derby together, laser alone and derby alone

- Weight: 1.7kg net, 2.0kg packed

- Packed Dimensions 310x250x180mm

4. Remote Control Operation

Functions:

1) Stand By: Standby mode for whole light

2) DMX: Enter DMX mode

3) Show 1: LED show with adjustable speed

4) Show 2: Laser show with adjustable speed

5) Show 3: LED & Laser show with adjustable speed

6) Show 4: LED & Laser show with fixed speed

Show 5- Show 8: no function

7) LED Color: choose LED colour

8) LED Random: LED random colour

9) Laser Color: Chose from red, green or both on.

10) Laser Random: Laser with random colour

11) Sound ON, Sound OFF: Turns on or off sound activation for shows 1-4. When sound is off,

the shows run in auto mode.

12) Speed: Increase or decrease speed of shows.

5. Menu Operation

6. DMX Channel Allocation and functions table

CH Function DMX value Details

CH1 Red dimming 0-255 Red dimming

CH2 Green dimming 0-255 Green dimming

CH3 Blue dimming 0-255 Blue dimming

CH4 White dimming 0-255 White dimming

CH5 LED strobe control 0-9 No strobe

10-255 Strobe speed from slow to fast

CH6 Master dimming 0-255 Master dimming

CH7 Laser color control

0-9 OFF

10-127 Red

128-199 Green

200-255 Red and green

CH8 Laser strobe control 0-9 No strobe

10-255 Strobe speed from slow to fast

CH9 LED motor control 0-127 Beam position

128-255 Motor speed from slow to fast

Addr(set DMX address)

1-512

Ver

Display Software version

Shou(show mode)

Soun(sound mode)

Adjust MIC sensitivity on rear panel

Sh 1:only LED effect with speed adjustable)

SPXX (speed 0-99)

Sh 2:only laser effect with speed adjustable

Sh 3:LED+laser effect with speed adjustable

Sh 4:LED+laser effect with fixed spe

SPXX (speed 0-99)

TeNP

Light temperature

CH10

Laser motor control 0-127 Laser position

128-255 Laser motor speed from slow to fast

CH11

Mode control

0-9 DMX mode

10-100 Show 1

，

LED (speed controlled by CH12)

101-150 Show 2

，

Laser (speed controlled CH12)

151-200 Show 3

，

LED+Laser (speed controlled by CH12)

201-255 Show 4

，

LED+Laser (at fixed speed)

CH12

Show speed 0-255 From slow to fast

CH13

Sound ON/OFF 0-127 Sound sensitivity OFF (for shows set by CH11)

128-255 Sound sensitivity ON (for shows set by CH11)

DMX-512 Control Connection

Using a 3 pin XLR cable, you can connect the product to a DMX controller and then to

other fixtures with 3 pin XLR inputs and outputs. When not using DMX, multiple

fixtures can be connected together and operate under master/slave control. The signal

cable should have two core with shielded cable, the signal connectors are XLR input

and output connectors. Please refer to the below diagram:

7. DMX Address Setting

When being used in conjunction with a DMX controller, each fixture must be set a specific

starting address. When receiving signal, fixture will receive channel control signals of this

address from the DMX controller.

For simplicity, the user can use the same address for multiple fixtures but this will result in

each fixture providing exactly the same output and fixtures with the same DMX address cannot

be individually controlled.

To control each fixture individually via DMX, each fixture must have its own unique DMX

address. As this fixture uses 13 DMX channels, each address must be at least 13 apart.

So for example – assuming the first fixture is DMX channel 1, the second fixture would need

to be on channel 14, then the 3

channel 27 and so on. Some DMX controllers may group

fixtures in lots of 16 channels – so in that case, fixture 1 on channel 1, fixture 2 on channel 17,

3 on 33, and so on. Refer to your DMX controllers’ instruction manual on how best to manage

your DMX channel allocation.

DMX Input DMX Output

First Address 001 Second Address 014 Third Address 027

8. DMX-512 connection with DMX terminator

A DMX terminator helps to reduce ‘noise’ on the DMX chain, and makes the light respond to

control more accurately. It should be plugged in to the last fixture in any chain. For Terminator

connections please see below:

9. Rigging:

1. Clamp

2. DERBY2 Yoke/handle

Use a suitable clamp to attach to the hanging bracket / yoke of the product. The mounting

bracket can then be attached to a stand, trussing or lighting bar securely. Be sure to use a safety

chain which connects through the lug on the back of the unit. The safety chain should have a

breaking strain more than ten times the weight of the product.

10. Cleaning and maintenance

From time to time it is recommended the product is cleaned to ensure maximum light output

and performance. Use a wet cloth to clean the housing as well as the lenses and base. Glass

cleaner is also suitable but alcohol based cleaners and solvents cannot be used as they will

cause damage to the product.

When used in a fixed long term installation such as a venue or club, the unit should be

periodically taken down from the installation and professionally cleaned. Dust build-up within

the unit can cause damage and ultimately failure of components.

11. Technical Data

Input Voltage: AC100-240V 50/60Hz

LED: 1 x 30w 4-in-1 RGBW LED

Laser: 150mW red laser 650nm & 50mW green laser 532nm

Power Consumption: 35w

Max ambient temp: 40

Max surface temp: 65

Net Weight: 1.70Kg

Packed Dimensions: 310x250x180mm

12. Warranty

This product is warranted for 2 years from your purchase date. We are confident that this

product will give many years of trouble-free operation but should an unlikely problem arise,

warranty claims must be via the original place of purchase, together with the original purchase

receipt. Please keep both your original purchase receipt and this instruction manual together

and in a safe place for future reference. Should the product be sold within the warranty period,

be sure to pass on both to the new purchaser so they are able to claim warranty should they

need to. We recommend you register your warranty online at www.industrygear.com.au.

Purchased from:_________________________________________

Contact Details:_________________________________________

Date Purchased:_________________________________________

Invoice/Receipt Number:__________________________________

Exclusively imported by LSW Imports and Distribution

PO Box 887, Kingsgrove, NSW, 2208

[email protected]

www.lightemotion.com.au

1800 643 111 (within Australia)

+612 9718 4900 (outside of Australia)

Table des matières

Autres manuels Light Emotion Équipement d'éclairage

Light Emotion

Light Emotion QUARK2GBC Manuel utilisateur

Light Emotion

Light Emotion LEDBAR1803 Manuel de l'opérateur

Light Emotion

Light Emotion Phantomrgb1700 Manuel utilisateur

Light Emotion

Light Emotion FLAT1012 Manuel de l'opérateur

Light Emotion

Light Emotion PARBAR Manuel de l'opérateur

Light Emotion

Light Emotion VIVID0312 Manuel de l'opérateur

Light Emotion

Light Emotion DMXDIM4LED Manuel de l'opérateur

Light Emotion

Light Emotion STROBA Manuel de l'opérateur

Light Emotion

Light Emotion LX90SPOT Manuel utilisateur

Light Emotion

Light Emotion DERBY3 Manuel de l'opérateur

Light Emotion

Light Emotion UVLED Manuel utilisateur

Light Emotion

Light Emotion QUARK2RBP Manuel utilisateur

Light Emotion

Light Emotion thunderboltg2 Manuel de l'opérateur

Light Emotion

Light Emotion PARBAR4 QUAD Manuel utilisateur

Light Emotion

Light Emotion MILKYWAY3 Manuel de l'opérateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur