Lifetime 72005 Guide de démarrage rapide
1
®
10/1/2006
VISIT THE LIFETIME WEB SITE:
WWW.LIFETIME.COM
COMPETITION SERIES POWERLIFT®
BASKETBALL SYSTEM
MODEL #72005
ASSEMBLY INSTRUCTIONS
AND OWNER’S MANUAL
WARNING
Failure to comply with any of the warnings in
these instructions may result in serious personal
injuries such as cuts, broken bones, nerve damage,
paralysis, brain injury, or death. Failure to comply
may also result in property damage. Please heed
all warnings and cautions. To ensure your safety, do
not attempt to assemble this system without reading
and following all instructions carefully. Identify and
inventory the parts using the Parts List.
**For U.S. and Canada Customers ONLY:**
IF ASSISTANCE IS NEEDED,
DO NOT CONTACT THE STORE!!!
CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) 225-3865
HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)
Call, or visit our Website for Saturday hours.
**Customers outside the U.S. or Canada, please contact the store.**
Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
INSTRUCTION #1019132
**A MINIMUM OF TWO ADULTS ARE
REQUIRED FOR ASSEMBLY**
Copy
2
PARTS LIST
HARDWARE IS ACTUAL SIZE
(Unless otherwise indicated)
(Not actual size)
(Not actual size)
(Not actual
size)
RA RB
RC
RD RF
RI RJ LA
LC
LD
LE
SAFETY INSTRUCTIONS
Most injuries are caused by misuse and/or not following instructions. Use
caution when using this system.
Owner must ensure that all players know and follow these rules for safe operation of
the system.
To ensure safety, do not attempt to assemble this system without following the
instructions carefully. Check entire box and inside all packing material for parts and/
or additional instruction material. Before beginning assembly, read the instructions
and identify parts using the hardware identier and parts list in this document.
Proper and complete assembly, use and supervision are essential for proper
orientation and to reduce the risk of accident or injury. A high probability of serious
injury exists if this system is not installed, maintained, and operated properly.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID WARRANTY.
• If using a ladder during assembly, use extreme caution.
• Two capable adults are recommended for this operation.
• Check base daily for leakage. Leaks will cause system to fall.
• Assemble the pole sections properly. Failure to do so could cause the pole
sections to separate during play or transport.
• Minimum operational height is 7’6” (2.23m) to the rim.
ID Part # Description Qty
TP 1018842 Top Pole 1
MP 1018878 Middle Pole 1
BP 1018882 Bottom Pole 1
PA HA01800 Gas Spring 1
PB 825619 Rim 1
PC 1018938 Short Y-Arm 2
PD 1018939 Long Y-Arm 2
PF 1018837 Rear Lifter Arm 2
PG ZA10185 Bellows 1
PH 1018977 Backboard 1
PI 502027H Adjustment Handle 1
PJ 502049G Trigger 1
FS16400 Warning Sticker (Applied) 1
PK 604091 Height Sticker 1
PM CF01700 Pole Cap 1
PN DD00800 Net 1
PO 502056 Plastic Guard 1
PP CA00885 Zip Tie 2
PQ 1008630 Spring Bracket 1
PR 800165 Rim Cover Plate 1
PT Z090013 Clamp Plate 2
PU Z090014 Hold Down Base Bracket 2
PV ZA01800 Bracket Back Plate 2
AG 510022 Wheel 2
AH BD00100 1/2” x 8” Axle 2
AI 510035 Base Cap 1
AJ 510082 Base 1
AK ZA02600 U-Bolt Washer Plate 1
AP 1018883 Pole Brace 2
AR CH00199 Slide Collar 1
AS CH00399 Locking Knob 4
AT 510011 Base Plug 1
AU CA00299 Left Frame Pad 1
AV CA00399 Right Frame Pad 1
AW CA00999 Bottom Frame Pad 2
AX 1018699 Slide Collar Clamp 1
AY 1018587 Slide Collar Bracket 2
Rim Hardware (1001327)
RA BS01000 #7 x 3/8” Screw 4
RB 300104 3/8” Push Nut 2
RC 302009 5/16” x 1 1/4” Carriage Bolt 2
RD 300128 Jam Nut 2
RE 302084 4” U-Bolt 1
RF 302090 5/16” Nylock Flange Nut 4
RG 1001137 Compression Spring 2
RH 510038 3/8” x 5 1/2” Axle 1
RI 804018 Rim Pivot Bracket 1
RJ 804033 Spring Retainer Plate 1
Competition Lock Down Hardware (HH00400)
LA 300145 3/8” Zinc Nut 2
LC 300203 3/8” x 5.31” J-Bolt 2
LD 300204 3/8” x 3/4” Eye Bolt 2
LE 302204 Cement Anchor 2
3
ID Part # Description Qty
Main Hardware (HH00600B)
MA 300029 1/2” x 7 1/8” Hex Bolt 3
MB 300040 1/2” Nylon Washer 4
MC 300031 3/8” Flat Washer 2
MD 300043 Cotter Pin 1
ME 300055 1 1/2” Metal Pin 1
MF BB00500 1/2” x 1 3/4” Hex Bolt 4
MG 301008 1/2” Centerlock Nut 7
MH 301051 3/8” x 5” Hex Bolt 2
MI 300073 1/2” Flat Washer 8
MJ 302008 3/8” Centerlock Nut 2
ML 500008 1/2” x 1/5” Spacer 4
MN 500041 3/8” x 1/4” Spacer 2
MQ 500081 Grease Packet 1
MK 500114 Finish Plug Cap 4
MR 800264 .510 x 3.91 Spacer 2
MT 800328 3/4” x 4 1/5” Spacer 1
Slide Collar Hardware (1013432)
SA 300186 #10 x 1” Self-Drilling Screw 4
SB 502073 Slide Collar Stop 4
SC 300027 5/16” x 3/4” Hex Bolt 1
SD 300097 5/16” Nylock Nut 1
Pole Joint Hardware (HD9081)
JA 300017 #10 x 5/8” Self-Drilling Screw 2
Frame Pad Hardware (HH00700)
FA BS00100 #10 x 3/4” Self-Drilling Screw 10
Handle Hardware (1017923)
HA 302007 3/8” x 6 1/2” Hex Bolt 2
HB 300101 Release Pin 1
MJ 302008 3/8” Centerlock Nut 2
HD 300187 1/2” x 6 1/2” Hex Bolt 1
MG 301008 1/2” Centerlock Nut 1
PARTS LIST
(Not actual size)
(Not actual size)
(Not actual size)
(Not actual size)
MB MC MD
ME
MF
MG
MH
MI MJ ML MN
MK
MR
MT
SA SB
JA FA
MA
HA
HB
HD
SC
SD
4
BEFORE BEGINNING ASSEMBLY
PARTS LIST
ID Part # Description Qty
Base Hardware (HH01800B)
BA 300073 1/2” Flat Washer 2
BD 300097 5/16” Nylock Nut 4
LA 300145 3/8” Zinc Nut 1
BF 300152 1/2” x 9” Hex Bolt 1
MG 301008 1/2” Centerlock Nut 1
BH 301050 3/8” x 1 1/2” Hex Bolt 2
MJ 302008 3/8” Centerlock Nut 2
MH 301051 3/8” x 5” Hex Bolt 1
BK 302071 5/16” x 3/4” Carriage Bolt 4
A. Identify and inventory all parts using the checklist boxes on the Parts
List. Keep the hardware bags and their contents separate. If any parts
are missing, call our Customer Service Department.
B. Test t all Bolts by inserting them into their respective holes. If
necessary, carefully scrape away any excess powder coating buildup
from inside the holes. Do not scrape away all of the powder coating.
Bare metal may rust. You may need to pound some bolts into place
with a hammer or mallet.
POLE SECTION IDENTIFICATION
Identify the pole sections before beginning assembly. Failure to assemble
the pole sections correctly may result in severe personal injury or property
damage as described on Page One.
ONCE THE POLE SECTIONS HAVE BEEN SEATED, THEY
CANNOT BE SEPARATED.
Note: Tapers and ares are exaggerated in the illustrations.
Top Pole:
Four holes at the
top of the pole, four
holes in the middle
and two holes at
the bottom.
Bottom Pole:
Slots at the top
of the pole and
two holes at the
bottom. Shortest
pole. Warning
Sticker.
Middle Pole:
Slots at the
top of the
pole.
TP MP
BP
BA BD BH BK
BF
Tools and Materials Required
for Assembly
(Not Included)
1. Adjustable Wrench
2. Hammer or Mallet
3. 1/2” Wrenches (2)
4. 9/16” Wrenches (2)
5. 3/4” Wrenches (2)
6. Scrap Wood or
Cardboard
7. Tape Measure
8. Electric Drill
9. Pliers
10. Funnel
11. 519 lbs. Sand or
Water supply
12. Phillips Screwdriver
13. Scissors or Wire
Cutters
14. Pencil or Marker
15. 1/2” Masonry Bit*
16. Hammer Drill*
*Optional for lockdown
feature
5
Required For This
Page:
MH
PQ
MJ
MR
MC
TP
TP
HH00600B
9/16” Wrenches
(2)
PK
Small
holes
Large
holes
The small notch in the Sticker
ts around the hole in the pole.
5” Mark
MP
TP
Make a mark 5
inches from the
slotted end of the
Middle Pole.
Strike the poles rmly on scrap
wood or cardboard ve to six
times.
Do not hit your feet with the pole,
as serious injury could occur.
TP
The poles must be seated together. Even if they reach the 5-inch mark before seating, you must strike them on
the wood ve to six times! Failure to seat the poles correctly could allow the poles to separate during use, which
could lead to property damage or serious personal injuries such as those listed on Page One.
WARNING
If your pole sections
do not reach within
1/2 inch of the 5-inch
mark after seating,
DO NOT COMPLETE
ASSEMBLY. Call
our Customer
Service number for
assistance.
(2)
(2)
(2)
The instructions in the following steps must be followed exactly. Failure to properly orient the
pole sections will render the pole unusable. If the pole sections are assembled incorrectly,
you will have to purchase new ones from our Customer Service Department.
*The back of the Top Pole (TP) is the side with the Spring Bracket. FRONT
SIDE
BACK
SIDE
Spring
Bracket
BP
MP
5-inch
mark
Make a mark 5 inches
from the slotted end of the
Bottom Pole (BP).
Slide the Middle Pole over
the Bottom Pole. Strike
each end of the pole rmly
on wood or cardboard ve
to six times.
MP
Both pole joints must be
within 1/2-inch of the 5-inch
mark. If either joint fails to
reach the mark, DO NOT
COMPLETE ASSEMBLY.
Call our Customer Service
number for assistance.
PQ
Slide the Top Pole
over the Middle Pole.
*The holes in the bottom of the Bottom Pole (BP) are toward the back of the pole. TP
Tighten the
Nuts securely.
Holes
BP TP
TP
Pencil or Marker
Tape Measure
Warning
Sticker
BP
MP
MP
Apply the Height Sticker (PK) so it
wraps around the opposite side of the
Pole as the Spring Bracket (PQ).
Make sure the Warning Sticker and the Spring Bracket are on opposite sides.
MJ
MH
MR
MC
321
4 5
6
1”
JA
JA
JA
JA
INSTALLING THE POLE JOINT
SAFETY SCREWS:
Required For This Page:
HD9081
Lay the pole on the ground.
The pole joint safety Screws do not replace
proper pole seating--both are required.
Always wear safety glasses when
operating power tools.
Measure up one inch from the lower pole joint
on the side of the pole with the Spring Bracket
and begin inserting the Screw (JA). Once the
Screw has entered the pole, slow the drill down
to avoid stripping the Screw.
(2)
You must follow all instructions for pole joint safety
Screw attachment and pole seating. Failure to do
so could allow the poles to separate, resulting in
property damage or serious personal injuries such
as those listed on Page One.
WARNING
Repeat the process for the upper pole
joint with the remaining Self-Drilling
Screw (JA).
AJ
Lay the Base upside down.
HH01800B
You may need to strike the Axles (AH)
with a hammer or mallet to drive them
into the slots.
Turn the Base over so the
Wheels are on the bottom.
Complete for the other side of the Base.
1/2” Wrench
(4)
(4)
Rubber
Gasket
AI
The Rubber Gasket should be
inside the Base Cap (AI). If there
is no Gasket, call the Customer
Service number on Page One.
Screw the Base Cap
onto the Base (AJ).
AI
AH
AH
AG
AG
BD
BK
PU
PV
Completely tighten the Nuts.
Hammer/Mallet
AJ
Electric Drill
987
6
JA
BD
BK
7
9/16” Wrenches
Required For This Page:
(1)
(1)
3/4” Wrenches
HH01800B
(1)
(Not
actual
length)
9”
(2)
The Spring Bracket
on the Top Pole
should face the
Base.
AP
Rest the Base at on the ground and have one
person support the pole.
Snap the Slide Collar (AR) onto the Middle Pole
and insert the Pole Braces (AP) into the Collar.
MH
AS
AX
Bend the Slide Collar Clamp
(AX) around the Slide Collar.
AX
One person should
position the Pole at
an angle in the front
of the Base. A second
person should slide
one washer onto the
bolt, then push the bolt
through the rst hole in
the base and the rst
hole in the pole.
Slide the Bolt (MH) through the Locking Knob (AS),
Slide Collar Clamp (AX), Slide Collar and Pole Braces.
The rectangular cutout
in the Clamp (AX)
should t over the
“Bubble Level” on the
Slide Collar.
AR
AP
MH
BF
BA
MG
10
11
Move the pole the
rest of the way
into the base and
slide the bolt the
remainder of the
way through the
pole and the other
side of the base.
Push washer and nut
onto the bolt and tighten
the bolt until it is at the
top of the thread.
MG
BA
BF
BA
BF
BA
8
9/16” Wrenches
Required For This Page:
HH01800B
(1)
(2) (2)
Pliers
Scissors or Wire Cutters
BH MJ
LA
AS
LA
Place the Knob (AS)
and Nut (LA) back onto
the bolt and tighten
completely.
Use another Bolt to tap the
3/8” Zinc Nut (LA) into the
Locking Knob (AS).
12 Place the Zinc Nut (LA) on the end
of the bolt and tighten in order to pull
the sides of the slide collar together.
LA
AX
Do not stand the system up until
the Base is lled with weight.
PG
PA
PG
Zip Tie
(PP)
PA
Larger
End
Use pliers to tighten
the Zip Ties (PP)
securely. Cut off the
ends of the Zip Ties.
Zip Tie
(PP)
MJ
BH
AP
Tighten each Nut only
until it is ush with the
end of the Bolt.
After the Pole Braces (AP) are attached
to the Base, loosen one of the Knobs on
the Slide Collar and adjust the pole until
it is upright. Tighten the Knobs securely.
Tip the system forward until the pole
rests on the ground.
The bottom of the Bellows (PG)
overlaps the Spring (PA) by 1”. The
top is 1/2” from the top of the Spring.
1413 Attach the pole braces (AP) to the
base on each side.
Remove the Zinc Nut (LA)
from the end of the bolt.
9
Required For This Page:
1017923
(2)
(2)
HH00600B
(2)
(1)*
(1)*
*(Not actual size)
(1)
Pliers
HA
MJ
PI
MN
Tighten the Nut until it
is ush with the Bolt.
MD ME
PQ
MD
PA
Use pliers to
bend the Cotter
Pin (MD) as
shown above.
HB
PA
The Release Pin (HB) should t into
the channels in the Trigger (PJ).
PJ
HB
PI
HA
PJ
PI
MJ
Tighten the Nut until it is
ush with the Bolt.
(1)*
(2)
1001327
RC
RI
RC
MG
HD
PI
Tighten the Nut until it is
ush with the Bolt.
PF
PA PF
Line up the Rear Lifter Arms
(PF) with the Gas Spring (PA).
PF
(1)
9/16” Wrenches
(1)
3/4” Wrenches
ME
PB
MG HB
HA
MJ
HD
RI
RC
MN
MD
ME
18
171615
19 20 21
10
Required For
This Page:
1/2” Wrenches
1001327
(2)
(4)
(4)
(Not
actual
size)
(1)
(2)
The Push Nuts (RB)
should be convex
side out.
RH
RB
RI
RB
RH
PO
RF
Lay the Backboard (PH) face
up with the Rim holes exposed
over the edge of a table.
RE
RE
RG
RD
RE
Tighten the Jam Nuts (RD) onto
the U-Bolt as far as they will go.
RF RF
RJ
Tighten the Nylock
Flange Nuts (RF) down
as far as they will go.
RA
PR
Insert the U-Bolt (RE) through the U-
Bolt Washer Plate (AK) and the upper
holes in the back of the Backboard.
AK
Screwdriver
RF
PH
PB
242322
25 26 27 28
RB
RF
RD
RJ
RA
RB
Table des matières
Autres manuels Lifetime Équipements de jeux et d'aires de jeux
Lifetime
Lifetime A-FRAME PLAYSET 90042 Manuel utilisateur
Lifetime
Lifetime 90641 Manuel utilisateur
Lifetime
Lifetime 290038 Manuel utilisateur
Lifetime
Lifetime ADVENTURE TOWER 91189 Manuel utilisateur
Lifetime
Lifetime 90797 Manuel utilisateur
Lifetime
Lifetime 90135 Manuel utilisateur
Lifetime
Lifetime ADVENTURE CASTLE 91090 Manuel utilisateur
Lifetime
Lifetime 90137 Manuel utilisateur
Lifetime
Lifetime 0040 Guide de démarrage rapide
Lifetime
Lifetime 90022 Manuel utilisateur
Lifetime
Lifetime 90993 Manuel utilisateur
Lifetime
Lifetime 90136 Manuel utilisateur
Lifetime
Lifetime 90952 Manuel utilisateur
Lifetime
Lifetime 90188 Manuel utilisateur
Lifetime
Lifetime 151110 Manuel utilisateur
Lifetime
Lifetime ADVENTURE TOWER 90440 Manuel utilisateur
Lifetime
Lifetime 90188 Manuel utilisateur
Lifetime
Lifetime 90941 Manuel utilisateur
Lifetime
Lifetime 1270 Manuel utilisateur
Lifetime
Lifetime BIG STUFF 91079 Manuel utilisateur
Manuels Équipements de jeux et d'aires de jeux populaires d'autres marques
Ledon
Ledon 302040 Manuel utilisateur
FUNormous
FUNormous Disney Junior MICKEY MOUSE Manuel utilisateur
b4Adventure
b4Adventure Slackers TREEZONE ADVENTURE THREE HOUSE Manuel utilisateur
PoolMaster
PoolMaster 72775 Manuel utilisateur
Palmako
Palmako 4743142009857 Manuel de l'installateur
BOERPLAY
BOERPLAY PSTE000.019 Manuel utilisateur
