LG DM5360K Manuel utilisateur
SERVICE MANUAL
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE UNIT, READ THE “SAFETY PRECAUTIONS”
IN THIS MANUAL.
Internal Use Only
JULY, 2016
MODEL: DM5360K (DM5360K, DMS5360F)
MODEL: DM5360K
(DM5360K, DMS5360F)
KARAOKE
MINI HI-FI SYSTEM
P/NO : AFN77552410
CONTENTS
SECTION 1 ........ GENERAL
SECTION 2 ........ CABINET & MAIN CHASSIS
SECTION 3 ........ ELECTRICAL
SECTION 4 ........ REPLACEMENT PARTS LIST
1-1
SECTION 1
SUMMARY
CONTENTS
SERVICING PRECAUTIONS ............................................................................................................................ 1-3
ESD PRECAUTIONS......................................................................................................................................... 1-5
HIDDEN KEY MODE ......................................................................................................................................... 1-6
SERVICE INFORMATION FOR EEPROM........................................................................................................ 1-7
PROGRAM DOWNLOAD & UPDATE GUIDE.................................................................................................. 1-8
SPECIFICATIONS ............................................................................................................................................. 1-9
1-2
1-3
NOTES REGARDING HANDLING OF THE PICK-UP
1. Notes for transport and storage
1) The pick-up should always be left in its conductive bag until immediately prior to use.
2) The pick-up should never be subjected to external pressure or impact.
2. Repair notes
1) The pick-up incorporates a strong magnet, and so should never be brought close to magnetic materials.
2) The pick-up should always be handled correctly and carefully, taking care to avoid external pressure and
impact. If it is subjected to strong pressure or impact, the result may be an operational malfunction and/or
damage to the printed-circuit board.
3) Each and every pick-up is already individually adjusted to a high degree of precision, and for that reason
the adjustment point and installation screws should absolutely never be touched.
4) Laser beams may damage the eyes!
Absolutely never permit laser beams to enter the eyes!
Also NEVER switch ON the power to the laser output part (lens, etc.) of the pick-up if it is damaged.
5) Cleaning the lens surface
If there is dust on the lens surface, the dust should be cleaned away by using an air bush (such as used
for camera lens). The lens is held by a delicate spring. When cleaning the lens surface, therefore, a cot-
ton swab should be used, taking care not to distort lens.
6) Never attempt to disassemble the pick-up.
Spring has excess pressure. If the lens is extremely dirty, apply isopropyl alcohol to the cotton swab.
(Do not use any other liquid cleaners, because they will damage the lens.) Take care not to use too much
of this alcohol on the swab, and do not allow the alcohol to get inside the pick-up.
Storage in conductive bag Drop impact
NEVER look directly at the laser beam, and don’t allow
contact with fingers or other exposed skin.
Magnet
How to hold the pick-up
Conductive Sheet
Cotton swab
Pressure
Pressure
SERVICING PRECAUTIONS
NOTES REGARDING COMPACT DISC PLAYER REPAIRS
1. Preparations
1) Compact disc players incorporate a great many ICs as well as the pick-up (laser diode). These components
are sensitive to, and easily affected by, static electricity. If such static electricity is high voltage, components
can be damaged, and for that reason components should be handled with care.
2) The pick-up is composed of many optical components and other high-precision components. Care must be
taken, therefore, to avoid repair or storage where the temperature or humidity is high, where strong magne-
tism is present, or where there is excessive dust.
2. Notes for repair
1) Before replacing a component part, first disconnect the power supply lead wire from the unit
2) All equipment, measuring instruments and tools must be grounded.
3) The workbench should be covered with a conductive sheet and grounded.
When removing the laser pick-up from its conductive bag, do not place the pick-up on the bag. (This is
because there is the possibility of damage by static electricity.)
4) To prevent AC leakage, the metal part of the soldering iron should be grounded.
5) Workers should be grounded by an armband (1 M)
6) Care should be taken not to permit the laser pick-up to come in contact with clothing, in order to prevent
static electricity changes in the clothing to escape from the armband.
7) The laser beam from the pick-up should NEVER be directly facing the eyes or bare skin.
Resistor
(1 M)Conductive
Sheet
Resistor
(1 M)
Armband
1-4
1-5
Electrostatically Sensitive Devices (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components
commonly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated
circuits and some field-effect transistors and semiconductor chip components. The following techniques should
be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off
any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a
commercially available discharging wrist strap device, which should be removed for potential shock reasons
prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive surface
such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can
generate electrical charges sufficient to damage ESD devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD
devices.
6. Do not remove a replacement ESD device from its protective package until immediately before you are
ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable conductive materials).
7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the
protective material to the chassis or circuit assembly into which the device will by installed.
CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL OTHER
SAFETY PRECAUTIONS.
8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion
such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate
static electricity sufficient to damage an ESD device).
CAUTION. GRAPHIC SYMBOLS
THE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHIN AN EQUILATERAL TRIANGLE, IS
INTENDED TO ALERT THE SERVICE PERSONNEL TO THE PRESENCE OF UNINSULATED
“DANGEROUS VOLTAGE” THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF
ELECTRIC SHOCK.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE
SERVICE PERSONNEL TO THE PRESENCE OF IMPORTANT SAFETY INFORMATION IN SERVICE
LITERATURE.
ESD PRECAUTIONS
1-6
HIDDEN KEY MODE
Push both Front key and Remote Control key to activate it for 5 seconds.
1. Disc Lock On/Off (CD Function Only Active)
Front Key : PLAY/PAUSE
Remote Control Key : STOP
2. Check Version and Option code
Remote Control Key : Setup Display 16:9 1, 3, 9, 7, 1, 3, 9 Enter. OSD Display.
3. Clear EEPROM
Front Key : PLAY/PAUSE
Remote Control Key : 0
4. Edit EEPROM
DVD Function Pause 1, 4, 7, 2
5. Amp Clip On/Off
Front Key : PLAY/PAUSE
Remote Control Key : 7
Amp Clip Mode Change (AMP Clip On AMP Clip).
6. Sound Bypass
Front Key : PLAY/PAUSE
Remote Control Key : 1
7. APD TEST
Front Key : PLAY/PAUSE
Remote Control Key : 2
POWER ON
Press ‘Pause’ key once.
Remote control ‘Pause’ ‘1’ ‘4’ ‘7’ ‘2’ key in order.
DVD LOGO Status (NO Disk status)
Change will be applied when power OFF ON.
Press number 0 ~ 9, Press character A ~ F (1 ~ 6 for a while)
Move to appropriate position
and make changes with remote control ‘, , , ’ key.
1-7
SERVICE INFORMATION FOR EEPROM
1-8
Caution:
• When downloading the file, you should neither unplug the USB device, change to the other function,
nor power off the device.
• USB device must be unplugged when the downloading process is completed.
• If security program (Water Wall) is activated on your PC, you must save the file to the USB storage device
and disable the security software, then download the file to your set.
• Before Updating the file, you should change the USB Function and then insert the USB device.
• If not, Sometimes system will be dead.
1. MPEG Program
1) File name is LG_DM5360LD1_1605270.rom
2) Put upgrade file into USB root directory. (No other file exist on root directory)
3) Change the mode to USB mode.
4) Insert the USB memory in the set.
5) It will start update process automatically with showing “MPEG UP” on Display window.
2. MCU Program
1) File name is DM5360_1605280.HEX
2) Put upgrade file into USB root directory. (No other file exist on root directory)
3) Change the mode to USB mode.
4) Insert the USB memory in the set.
5) It will start update process automatically with showing “MCU UP” on Display window.
6) If the update is finished, the set will turn off automatically.
PROGRAM DOWNLOAD & UPDATE GUIDE
SPECIFICATIONS
1-9
• GENERAL
Power requirements Refer to main label.
Power consumption Refer to main label.
Networked standby 0.5 W (If all network ports are activated.)
Dimensions (W x H x D) Approx. 204.5 mm x 278 mm x 285.5 mm
Net Weight (Approx.) Approx. 2.7 kg
Operating temperature 5 °C to 35 °C
Operating humidity 5 % to 90 %
• INPUTS/ OUTPUTS
AUX IN 2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
VIDEO OUT 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
HDMI 19 pin (Type A, HDMI™ Connector ) x 1
Microphone (MIC) Sensitivity 20 mV (1 kHz), 6.3 mm jack x 2
• AMPLIFIER (RMS Output power)
Total 230 W
Front 115 W x 2 (4 Ωat 1 kHz, THD 20 %)
• TUNER
FM Tuning Range 87.5 to 108.0 MHz or 87.50 to 108.00 MHz
• SYSTEM
Frequency response 100 to 20,000 Hz
Signal-to-noise ratio 75 dB
Dynamic range 75 dB
Bus Power Supply (USB) 5 V 500 mA
USB Version 2.0
• FRONT SPEAKERS
Type 2 Way 2 Speaker
Impedance 4 Ω
Rated Input Power 115 W
Max. Input Power 230 W
Dimensions (W x H x D) Approx. 203 mm x 284.5 mm x 200 mm
Net Weight Approx. 2.1 kg
• Design and specifications are subject to change without notice.
Autres manuels pour DM5360K
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels LG Système stéréo
