LG 26TS30MF Manuel utilisateur

•Openframe

•Media Player

•Transparent

•Video Wall

•Other Models

•Accessories

MONITOR SIGNAGE MODELS

V3.2

1 OPENFRAME SIGNAGE

1-1. Keep temperature (Mandatory)

1-2. Consider using a cooling & heater solution(Mandatory)

1-3. Do not disassemble Handle, Fan or Side bracket(Mandatory)

1-4. Check Screw hole depth to avoid LCD panel damage(Mandatory)

1-5. Please install cooling system when exposed to direct sun light(Mandatory)

1-6. Use the side bracket to mount into an enclosure

1-7. Refer to brightness of according to ambient luminance

1-8. How to measure fan noise when it is installed indoors

1-9. Be careful not to damage the cable within an enclosure

2 MEDIA PLAYER

2-1. Install dust filter & keep temperature 0°C ~ 40°C(Mandatory)

2-2. Minimum distance between media player and structure(100mm)

2-3. the importance of periodic cleaning for ventilation area (Mandatory)

3 TRANSPARENT SIGNAGE

3-1. Preparation for Installation

3-2. Portrait mode: Rotate the set clockwise 90°(Mandatory)

3-3. Attach the product by using the screw holes (Mandatory)

3-4. How to connect cable assembly

3-5. Reference guide to the ventilation hole of enclosure

3-6. Reference guide to lighting set up

3-7. Reference to storage place(AD Board & Media Player)

3-8. Dimension of screw holes(26TS30MF/47TS30MF)

3-9. Recommendation: Lighting should be 600 LUX or more

3-10. Recommendation of operation Time

4 VIDEO WALL

4-1. Precaution when moving and handling

4-2. Installing the product

4-3. Tiling Displays (How to join Sets)

4-4. How to daisy chain monitors

4-5. Function Setting(Multivision Configuration)

4-6. Setting the Installation Menu

4-7. Setting the Tile Mode

4-8. Setting the Picture ID

4-9. The Heat Distribution of 47WV30

CONTENTS

4-10. Guide for installing the signage to reduce gap

4-11. White Balance Calibration Instruction

4-12. How to prevent the panel falling out

584WS70(84 inch UD Signage)

5-1. Keep temperature 0°C ~ 40°C(Mandatory)

5-2. The Handles are removable

5-3. Do not use a screw that is longer than 19.8mm (Mandatory)

5-4. Dimension of 84WS70MS

5-5. Use the Eye-Bolt Bracket to lift

5-6. Use the vesa screw holes for stand

5-7. Guide for Screw Size (Mandatory)

6 The other check point

6-1. Do not install such as face down or face up direction

6-2. Avoid installing the in-door signage at out-door

6-3. Guide for installing when product is close to the window

6-4. The TV module applied model & Image sticking

6-5. Enclosure design guide to prevent dust (Indoor)

6-6. Check the Baud Rate & RS-232C cable

6-7. Keep the distance for embedded installation

6-8. Firmware update by SuperSignElite-c

6-9. Guide for how to install correctly to the bracket

6-10. How to check Signage power off history

6-11. Digital Signage SW download method

6-12. SuperSign SW download method

6-13. Signage SW version box label mark

6-14. Avoid installing the product at oily environment when mounting

to the wall by using a wall mounting bracket

6-15. Check the Input Label when Signage is set up with a PC/Media Player

6-16. Do not spray directly onto the screen when cleaning the monitor

by using a cleaning liquid

6-17. Check the Guide Spacer when installing wall mount

6-18. Be careful not to fall off the wall metal material

6-19. Check the USB device is bad or not

CONTENTS

7 Accessories

7-1. How to connect the Stand

7-2. How to clean Touch Overlay

7-3. How to connect the OPS with KT-OPSA

CONTENTS

OPENFRAME SIGNAGE

1-1. Keep temperature (Mandatory)

When designing the enclosure, the temperature inside the enclosure must be maintained

as optimal temperature

The Measurement method for checking the operating temperature inside the enclosure

Enclosure

Openframe Signage (eg. 47WX50MF)

5cm

Thermal sensor

5cm

5cm Example

1. Should install a thermal sensor inside the enclosure.

There are three location for thermal sensor.

(backside of the top , backside of the middle,

backside of the bottom)

2. On this basis of you measuring the temperature,

Ensuring that you keep the temperature

47WX50MF

> 0°C ~ 40°C

72WX70MF

> 0°C ~ 50°C

1-2. Consider using a cooling & heater solution (Mandatory)

To maintain the temperature inside the enclosure, you should consider using a cooling

and heater solution such as an air conditioner, heat exchanger, or combined cooler

and heater depending on the external environment. (Please see below examples)

You could also employ an air flow circulation system and air curtain* between the front

panel and the enclosure.

Example 2 : Enclosure (Heat exchanger)Example 1 : Enclosure (Just fans)

Example 4 : Direct Air Cooling SolutionExample 3 : Enclosure (Air conditioner)

Air Curtain Air Curtain

Heater

Membrane Filter

FAN

Humidity Sensor

Protection

glass

Recommend to design the exterior of the enclosure to meet with the IP65 standard.

Use a dust filter to prevent dust .(At air inlet and outlet )

Filter should be used for filtering out bugs, dust and water.

For preventing from rust of lead frame in circuit board,

operates the Heater if relative humidity is high.

*Air curtain :

Air flow circulation system between

the front panel and the enclosure. 6

1-3. Do not disassemble Handle, Fan or Side bracket (Mandatory)

Do not disassemble the parts such as Handle, Fan or Side bracket

for preventing of product safety & function problem

Handle

Side bracket

Fan

*47WX50MF

47WX50MF

72WX70MF (No Handle, Side bracket)

Fan

[ Rear side ]

1-4. Check Screw hole depth to avoid LCD panel damage(Mandatory)

You must use the side screw holes when mounting the panel

The Side screw holes are M4.0 Tap , Torque 4~5Kgf.cm, pitch 0.7mm

The Screw hole depth of the panel is: 9.0mm (Max)

If a screw is longer than 9.0mm, it may cause damage to the LCD panel

It is advisable to only use spring washer-type screws.

Side Hole

47WX50MF

47WX50MF

▪Example : Spring washer type

You must use the side screw holes when mounting the panel

The Side screw holes are M6.0 Tap ,Torque 4~5Kgf

(Top and bottom sides: 5 holes for each, left and right sides: 3holes for each)

The Screw hole depth of the panel is:16.0mm(Max)

If a screw is longer than 16.0mm, it may cause damage to the LCD panel

47WX50MF

Side screw hole of panel

72WX70MF

72WX70MF

1-5. Please install a cooling system when exposed to direct

sun light (Mandatory)

NOTE

•To prevent sunlight, consider to attach a UV film on the glass

•For Example-Using a canopy may prevent the enclosure temperature increasing

due to direct sunlight.

Example

Autres manuels pour 26TS30MF

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels LG Moniteur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation

Sceptre

Sceptre D40 Manuel utilisateur