LG 42LA613V.AEK Manuel utilisateur

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels LG Téléviseur LED

Manuels Téléviseur LED populaires d'autres marques

Samsung

Samsung QE43LS03A Manuel utilisateur

Philips

Philips 55PUS6272/12 Manuel utilisateur

TCL

TCL L40E3020F Manuel utilisateur

Seiki

Seiki SC-55AU300 Manuel utilisateur

Sharp

Sharp AQUOS LC-60LE650U Manuel utilisateur

Durabase

Durabase L24H472S4VD Manuel utilisateur

Tesla

Tesla 43K625BUS Manuel utilisateur

Changhong Electric

Changhong Electric UD55GHE6000Ai Manuel utilisateur

Sharp

Sharp LC-32LE511E Manuel utilisateur

Samsung

Samsung The Terrace LST7T Series Manuel utilisateur

Saba

Saba SB40FDS195 Manuel utilisateur

Philips

Philips 43PFT5102 Manuel utilisateur

SWEDX

SWEDX SS-42K15 Manuel utilisateur

Akai

Akai LT-3222AD Manuel utilisateur

Bush

Bush DLED55UHDSFIRE Manuel utilisateur

Philips

Philips 32PFL3078K/12 Manuel utilisateur

Philips

Philips 4111 Series Manuel utilisateur

Toshiba

Toshiba 32S255 Series Manuel utilisateur

User Guide

This is a 「User Guide」 installed on the TV.

The contents of this guide are subject to change without prior notice for quality

improvement.

GP2



 





GP2

eng

❐To set favourite programmes

SETTINGS ➾ SETUP ➙ Programme Edit

1 Select the channel you want.

2 Press the FAV button to select Favourite Group and then OK.

✎You can check your favourite channels by pressing the LIST button on the

remote control.

❐To use Favourite

Press the FAV button.

You can only view the channels you set as favourites.

GP2

eng

Press GUIDE button.

[In Digital mode only]

Obtains information about programmes and airtime. Checks the broadcasting

time of the desired programme and schedule viewing.

GP2

eng

❐Automatically Setting Up Programme

SETTINGS ➾ SETUP ➙Auto Tuning

Automatically tunes the programmes.

1 Select Country where the TV is used. Programme settings change depending

on the country you choose.

2 Initiate Auto Tuning.

3 Select Input Source of your choice.

4 Set Auto Tuning following screen instructions.

✎If Input Source is not connected properly, programme registration may not

work.

✎Auto Tuning only finds programmes that are currently broadcasting.

✎If Lock System is turned on, a pop-up window will appear asking for

password.

GP2

eng

❓Cable DTV Setting option

When searching for programmes using FULL setting it can take a long time. The

following values are needed in order to search all available programmes quickly

and correctly. The commonly used values are provided as “default”.

• Frequency : Enter a user-defined frequency.

• Symbol rate : Enter a user-defined symbol rate (Symbol rate: Speed at which

a device such as modem sends symbols to a channel).

• Modulation : Enter a user-defined modulation. (Modulation: Loading of audio

or video signals onto carrier).

• Network ID : Unique identifier allocated for each user.

• Start Frequency : Enter a user-defined start frequency range.

• End Frequency : Enter a user-defined end frequency range.

GP2

eng

❓Satellite Setting Option

• Satellite : Select your desired Satellite.

• LNB Frequency : [Depending on country] Select one value from 9750/10600,

9750/10750, 9750, 10600,10750, 5150, MDU1, MDU2, MDU3, MDU4, MDU5.

If you select 9750/10600, 9750/10750(MHz), 22KHz Tone is disabled. If you

cannot find the LNB frequency value from the list, select User and manually

enter the frequency.

• Transponder : Select the transponder you want to tune.

• 22KHz Tone : When using 22KHz Tone switch, select A or B. If you use 22KHz

Tone, Unicable and Motor Type are disabled.

• LNB Power : To enable the power supply for the LNB, select On. If you select

Off, Motor Type is disabled.

GP2

eng

• DiSEqC : When using DiSEqC, select one option from A~D/ToneA~B. If you

use DiSEqC, Unicable and Motor Type are disabled.

• Unicable Settings : Select On to use Unicable and set the Unicable in the

Unicable Setting menu. When Unicable is enabled, 22KHz Tone, DiSEqC,

Motor Type are disabled.

• Motor Type : Select Motor Type to use Motor and set the Motor in the Motor

Setting menu. When Motor is enabled, 22KHz Tone, DiSEqC, Unicable are

disabled.

✎If you set satellite to others, you must add a transponder using Manual

Tuning.

✎When selecting 22KHz Tone and DiSEqc, you must connect them in the same

position as displayed on the OSD.

✎If you delete a Satellite, all programmes stored in the Satellite are deleted.

GP2

eng

❓Motor Setting Option

• DiSEqC 1.2 : Control motor to change satellite dish position.

Drive Direction : Select the direction in which you want to move the motor.

Drive Mode : Two modes are available: Step and Continuous.

-Step: The motor moves based on the value you enter (from 1 to 128).

-Continuous: The motor moves continuously until you press the Stop.

Test TP : Select the test TP you want to tune.

Set Limit : Set the motor movement to east or west to have the motor move

only within the direction set.

-On: You can limit the movement to the current direction by selecting the

West/East.

-Off: You can cancel the limit you set.

GP2

eng

Go To Zero: You can move the motor to Zero

Store: You can save the motor’s current direction.

• USALS : Set your current location(Longitude/Latitude).