LG 65UL3E Manuel utilisateur

INSTALLATION MANUAL

Please read this manual carefully before operating your set

and retain it for future reference.

65UL3E

75UL3E

86UL3E

www.lg.com

LG Digital Signage

(MONITOR SIGNAGE)

ENGLISH

Table of contents

3 Location and Function of Controls

3 Parts and Button

3 Basic functions

4 Firstuse

5 Basic Settings

5 - Language & Location

5 - Network Settings

6 Data Cloning

6 Installation Menu Settings

6 Installation Menu

6 Introduction

7 Public Display Settings

7 - Public Display Settings

7 - Power On Status

8 - Volume

8 - Key Management

9 - Limited Mode

10 - Power On Default

10 - Aux Source Setting

10 - Power Management

10 - Factory Reset

11 Network

11 - MAC Address

11 - Network Setting

12 - Wake On LAN

12 - Server Setting

13 General

13 - Configuration Setup

15 - Set ID Setup

15 - Power Saving

16 - HCEC Setup

17 - Clock Setup

17 - Password Change

17 - Lock Mode

17 - Crestron

18 Portal Settings

18 - PreLoaded App

19 Media Share

19 - Screen Share

19 - DIAL

19 - Signage Name

19 - SoftAP

20 - Beacon

21 Signage Manager

28 - USB Download Menu

29 IR Codes

30 External control device Setup

30 RS-232C Setup

30 Phone jack Type

30 Type of Connector : D-Sub 9-Pin Male

31 RS-232C Configurations

31 Communication Parameters

31 IR OUT Using Guide

31 - Suitable / Not Recommend remote-controller data

format

31 - IR Receiver specifications

32 Command Reference List

32 Transmission / Receiving Protocol

ENGLISH

Location and Function of Controls

Parts and Button

Basic functions

Power On (Press)

Power O1(Press and Hold)

Menu Control (Press2)

Menu Selection (Press and Hold3)

1 All running apps will close.

2 You can access and adjust the menu by pressing the button when Signage is on.

3 You can use the function when you access menu control.

ENGLISH

Firstuse

* Image shown may differ from your Signage.

•There are three options - Basic Settings, Data Cloning, and Installation Menu Settings. Each menu can access by START button.

ENGLISH

Basic Settings

This menu is for basic settings related to language, network setting.

Language & Location

•Select the Language and Country. Some countries need to select the Time Zone.

Network Settings

•Set Network connection. You can connect easily to wired/wireless network. (“Network Setting”on page 11)

ENGLISH

Data Cloning

Access Data cloning menu of Signage Manger application for applying cloning le.

Installation Menu Settings

Access Installation menu for Signage feature settings.

Installation Menu

* Image shown may differ from your Signage.

Introduction

The abundant functions for Signage linked with software installation can be projected on OSD as‘Installation Menu’.

The wide range of features can be performed simply on additional window to enhance the Signage’s easy installation and convenient operation for

System Integrators.

1 Press the Setting button for more than 5 seconds using the user remote control, banner will appear at top left on the screen.

2 Enter a four digit password and press button.

-The initial password“1-1-0-5”.

ENGLISH

Public Display Settings

When‘Public Display Settings’is set to On (Work), all functions of Public Display Mode apply.

Public Display Settings

•Decide to work all functions of‘Public Display Settings’or not by setting‘Public Display Settings’as On (Work) or O (Do Not Work).

•When‘Public Display Settings’is set to On (Work), all functions of Public Display Mode apply.

•When‘Public Display Settings’is set to O (Do Not Work), all functions of Public Display Mode Do Not apply.

•When it is set to‘On’, all items reserved at the Schedule list are deleted and the reservation function is not supported. (applied for the model

oering the reservation function)

Power On Status

•Decide to select working status of Signage Set when turn on main power.

•You can set with PWR, STD, LST.

•PWR always make Signage set On status when turn on main power.

•STD make Stand-by status when turn on main power.

•LST make Signage Set work like previous power status. As same concept as Power Backup mode; If main power were turned o in Power On

status, Signage Set would work in On status. If main power were turned o in Stand-by status, Signage Set would work in Stand-by status.

•If there Block All is both IR Operation and Local Key Operation from Key Management, In order to provide the Option that must be able to turn

on the Signage in the Signage turned o situation, change the value of the PWR. (Reference the Key Management)

ENGLISH

Volume

•Decide to apply volume policy of‘Start Volume’,‘Maximum Volume’and ‘MinimumVolume’as On (Work) or O (Do Not Work).

•(0 ≤ Min ≤ Start ≤ Max ≤ 100)

Start Volume

•This entry sets the start volume level when is power on.

-The level is specified as a number between minimum volume to maximum value. (Min ≤ Start ≤ Max)

-The default setting is‘Off’(disabled).

-When enabled, if the value is lower then the minimum specified in the minimum volume entry, the minimum volume entry must be

used.

-When enabled, if the value is larger then the maximum specified in the maximum volume entry, the maximum volume value must be

used.

Maximum Volume

•This entry sets the maximum volume level the set. The level is specied as a number between‘Minimum Volume’to 100. (Min ≤ Max ≤ 100).

-If the command volume up to higher than maximum volume’is received, that should be ignored.

-The default value is 100.

Minimum Volume

•This entry sets the minimum volume level the set will produce.

-The level is specified as a number between 0 to‘Maximum Volume’. (0 ≤ Min ≤ Max)

-If the command volume down to lower than minimum volume is received, that should be ignored.

-The default value is 0.

Key Management

•Manage key usability of Local(Front) Key and Remote Control. When selected to‘On’, following‘IR Operation’and ‘Local Key Operation’will be

worked by below.

IR Operation

•Decide whether work the LG remote control or not.

-When‘IR Operation’is set to 'Normal', all remote keys are available.

-'Use PWR Only' makes block all remote keys except power key.

-When‘IR Operation’is set to 'Block All', all normal remote keys don’t work.

Local Key Operation

•Decide to operate 'Local/Front Key' working behavior by setting‘Local Key Operation’as 'Normal', 'Use PWR Only' and 'Block All'.

-When‘Local Key Operation’is set to 'Normal', all local keys are available.

-'Use PWR Only' makes block all local keys except power key.

-When‘Local Key Operation’is set to 'Block All', all local keys don’t work.

ENGLISH

Limited Mode

•Congure Signage function’s limitation. When selected to‘On’, following sub-menus will be worked by below.

Menu Display

•Function to decide whether work with menu (including relevant menus too) of control key (On – Enter possible) or not (O – Enter

Impossible).

-Although select Off (Enter impossible), the action that press a Menu button for 5 seconds to enter‘Installation Menu’is available.

-When select On (Enter possible), Menu works.

OSD Display

•Decide to display OSD or not by setting‘OSD Display’as On (Display) or O (Do not Display).

-When‘OSD Display’is set to‘Off’(Do not Display), all OSD is not displayed except some exception.

-Although select‘Off’(Do not Display), the action that press a Menu button for 5 seconds to enter‘Installation Menu’and entering service

menu are available. (In-Start, Power-Only, Adjust, Installation Menu...)

System Provider Mode

•‘System Provider Mode’allows access to the menu system from the front panel or remote control but access is controlled as follows:

-When value is‘On’, Accessible Items on the menu system, others are not permissible. (Depending on model)

»Input select screens

»Sleep timer

»Aspect Ratio

»'Music' /‘Network’/‘Bluetooth’Menu.

»Input Manager

ENGLISH

Power On Default

•Set to On (Work) or O (Do Not Work).

•When‘Power On Default’is set to O, it is not applied to the subordinate Input, A/V Setting, Aspect Ratio menu.

•When Power On Default is set to On, it can set by entering the subordinate menu.

Input

•Set whether it is turned on by the set input source or by the last stored input source.

A/V Setting

•If‘A/V Setting’is changed from‘O’ to‘On’, A/V parameters that are set before entering‘Installation Menu’are applied whenever turn on power.

Aspect Ratio

•The aspect ratio determines the default aspect ratio that the set returns to on power up.

Aux Source Setting

•Set to On (Work) or O (Do Not Work).

•The Auxiliary (Input) Source Setting feature will enable or disable for each external input.

•User cannot disable the current input’s‘Aux Source Setting’.

Power Management

•The Power Management feature will turn o the Signage if no input control command is received from either the Local or IR Key within a

selected hours.

-Activity on either of these inputs shall reset the‘Power Management’timer and prevent interruption of Signage viewing.

-This entry can be set to a value which is corresponding to the desired hours (1 hour to 7 hours).

-Default value is‘Off (disabled)’.

Factory Reset

•Change all settings to their default values.

Autres manuels pour 65UL3E

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels LG Affichage numérique

Manuels Affichage numérique populaires d'autres marques

SMART-AVI

SMART-AVI SIGNAGEPRO Manuel utilisateur

KeyWest Technology

KeyWest Technology BREEZE Manuel utilisateur

XtendLan

XtendLan XL-DSP-183C Manuel utilisateur

Dynascan

Dynascan DS861LR4 Manuel utilisateur

Classic Exhibits

Classic Exhibits SEGUE DESIGNS MOD-1363 Manuel utilisateur

protech

protech KT-7290 Manuel utilisateur

WebDT

WebDT 515A Instructions de montage

Samsung

Samsung IWJ Series Manuel utilisateur

EVERI

EVERI Enrollment Kiosk Manuel utilisateur

NCR

NCR SelfServ 90 Manuel

ViewSonic

ViewSonic EP4602 Manuel utilisateur

ViewSonic

ViewSonic EP3202r Manuel utilisateur

Samsung

Samsung OM46N Manuel utilisateur

Viessmann

Viessmann 6336 Manuel utilisateur

Osram

Osram Traxon Manuel d'instructions d'installation

Philips

Philips Signage Solutions Series BDL4990VL Manuel utilisateur

ViewSonic

ViewSonic EP5012-L Manuel utilisateur

Philips

Philips CRD01/00 Manuel utilisateur