LG BT30N Manuel utilisateur

To enjoy fully all the features and functions of your product,

please read this owner’s manual carefully and completely.

OWNER’S MANUAL

Slim Blu-ray Disc Writer

BT30N

ENGLISH

Safety Instructions

CAUTION: The laser used in the writer can damage your eyes. Do not

attempt to open the cover. To reduce the risk of electric shock, do not

remove the cover (or back).

There are no user-serviceable parts inside. Refer servicing to qualied

service personnel. Use of controls or performance of procedures other

than those specied herein may result in hazardous radiation exposure.

WARNING: To reduce the risk of fire or electric shock, do not expose this

appliance to rain or moisture.

FCC COMPLIANCE STATEMENT

Note : This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

- Consult the dealer or an Authorized Service Center for help.

• FCC WARNING

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

•

This product is for use only with UL listed personal computers that have

installation instructions detailing user-installation of card cage accessory.

Contents

CAUTION: CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION

WHEN OPEN AND INTERLOCKS DEFEATED.AVOID EXPOSURE TO

THE BEAM.

CLASS 1 LASER PRODUCT

Safety Instructions 1

Introduction 3

Using the Drive 4

Drive Connectors 7

Troubleshooting 8

Specications 10

Information in this document is subject to change without notice.

©2014HLDS,Inc.Allrightsreserved.

Trademarks used in this text: HLDS is a trademark of HLDS, Inc.; LG and the LG logo are

trademarks of LG Electronics., Inc. Microsoft and Windows are registered trademarks of

Microsoft Corporation.

Introduction

Drive Description

This drive reads and writes to CD, DVD, and BD media. This drive has a 12.7 mm

tray form factor.

Features of the Drive

• 12.7mm height internal slim BD-RE Drive.

• CD-R/RW, DVD-R/-R DL/ -RW/ +R/ +R DL/ +RW, DVD-RAM, BD-RE/R read and

write compatible.

• CD Family, DVD-ROM and BD-ROM/R/RE read compatible.

• Active OPC (Running OPC)1 “Optimum Power Controller” provides for more

reliable writes.

• Easy-to-use drawer loading mechanism.

• Enhanced-IDE (ATAPI) model: SATA Interface.

• Supports BDXL media (BD multi-layer) read and write

• Improved Buffer Under- Run Error handling through the Preventive function.

1. Continuously monitors the signal level during recording and adjusts the laser

power to compensate when the disc is dirty, insuring a at signal.

Using the Drive

Front Panel

This following is the general gure of the design of the drive. The drive’s

appearance and specications may change without prior notice.

1.EmergencyEjectHole

If the disc tray does not open when you press the eject button, power off the

computer, insert a pin or unfolded paper clip in the hole and push rmly.

2. Indicator Light

The light blinks when there is drive activity.

3. Disc Tray

The disc tray opens automatically when you press the eject button. When you

place a disc in the tray, ensure that the label on the disc is facing outwards. If

you are not loading or unloading a disc, the tray should remain closed.

4. Eject Button

Press this button to open/close the disc tray. This button works only when

power is supplied to the drive.

Drive Operation

Inserting a Disc

• Press the eject button. The disc tray will be ejected.

• Place the disc in the center of the tray with the label side facing up.

• Push disc onto hub until secure.

• Push the disc tray by hand and close completely.

Removing a Disc

• Press the eject button. The disc tray will be ejected.

• Remove the disc.

• Push the disc tray till it closes completely.

NOTE: During some drive activities, the drive will not allow the tray to open even

when the eject button is pressed.

Usage Guidelines

• Do not press down on the disc tray when it is opening or closing.

• Do not place objects on the disc tray.

• Never use a damaged, broken, scratched, or deformed disc.

• Keep the disc tray closed when the drive is not in use.

NOTE: High-speed drives spin the disc at a high rotational speed. If a disc has

printing on only half of the disc, or if there is a slight imbalance in the disc, the

imbalance is greatly magnied by the high speed, causing the drive to vibrate or

produce a fan-like noise. These effects are inherent in the high-speed technology

and do not indicate a problem with the drive.

Emergency Eject

The procedure described below can be used to remove a disc from the drive if

the eject button is disabled by software or a power failure occurs.

1. Turn the computer off.

2. Insert a small diameter rod or a stiff wire (a straightened paper clip about

1.2 mm [0.047 in] in diameter) into the emergency eject hole and push

rmly.

3. The disc tray is ejected by about 10 mm (0.39 in). Pull the disc tray out.

NOTE: Do not insert more than 50 mm (1.9 in) in depth.

Inserting more than 50 mm (1.9 in) may damage the drive.

Cleaning Media

If dust or ngerprints get on the disc, wipe it with a soft cloth

from the center to the edge.

CAUTION: Do not use benzene, paint thinner, record cleaner, solvent or static

repellent. This can damage the disc.

Cleaning the Drive

Cleaning the inside of the drive is not recommended.

Drive Connectors

Slim SATA Drive Connectors

Troubleshooting

Please refer to the Introduction section to determine if the drive in your system

is a slim device.

Symptoms and Solutions

Solutions

1-1. Turn off the system, remove the drive, and re-insert back

to the system.

2-1. If the disc is dirty (ngerprints, etc.), clean it with a

non-abrasive cloth from the disc center hole to the outside.

2-2. If the disc is scratched and warped, do not insert it into

the drive.

2-3. If the disc is inserted upside-down, re-insert it in the

proper direction.

2-4. Check to see that the necessary software applications are

installed correctly.

3-1. This drive only supports discs with the formats indicated

in the Specications section. It cannot read the data on discs

with other formats. Check the disc’s format.

4-1. The CD player application may need to be set to “Digital.”

In Windows Media Player, for example, from the menu bar,

click on “Tools,” then “Options,” and then click on the “Device”

tab. Select the drive and click on the “Properties” button. Set

the playback mode to “Digital.”

5-1. Ensure disc is clean and free of scratches.

5-2. Media from different manufacturers or purchased at

different times will record at different speeds. The drive will

adjust the available recording speeds to achieve the highest

write quality.

6-1. Check to see that the system is powered up.

6-2. For drives with LED indicator and it does not light up,

refer to section 1 above.

6-3. Use Emergency Eject Instructions to open the tray.

Please refer to the Using the Drive section.

6-4. If the system is capable of booting into an operating

system, attempt to issue an eject command from within the

operating system.

Symptoms

1. Drive is not

recognized by system.

2. Cannot read or play

disc.

3. Certain types of disc

do not play.

4. When playing an

audio CD, drive shows

disc activity but there is

no sound.

5. Drive will not write

or read at maximum

speed.

6. Cannot eject disc.

Solutions

7-1. Is the disc loaded in the drive with the read/write surface

facing the right direction? The label should be up. If a disc

does not have a label, the disc code on the inner side of the

disc should be properly oriented for reading when looking from

the top of the disc.

7-2. CD-R, DVD+R, DVD-R, and BD-R discs cannot be

re-written.

7-3. Please check the type of disc that is being used. Please

refer to Specications section to ensure that the disc type is

supported by this drive.

7-4. Is there enough free space on the writable disc?

7-5. Did a screen saver or other application operate while

writing to the disc? If so, try again with the application turned

off.

Symptoms

7. Cannot write to disc

(for drives with write

capability).

Table des matières

Manuels Lecteur Blu-ray populaires d'autres marques

Samsung

Samsung BD-F5900 Manuel utilisateur

Philips

Philips BDP3380K Manuel utilisateur

Samsung

Samsung BD-P4600 Manuel utilisateur

Sharp

Sharp BD-HP17U - AQUOS 1080p Blu-ray DiscTM Player Manuel utilisateur

Pioneer

Pioneer BDP-140 Manuel d'installation et d'exploitation

Samsung

Samsung BD-D8200A Manuel utilisateur

Sony

Sony BDP-S300 - Blu-Ray Disc Player Manuel utilisateur

Marantz

Marantz UD9004 Manuel utilisateur

Panasonic

Panasonic DMR-HCT230 Manuel utilisateur

Panasonic

Panasonic Diga DMR-PWT420 Manuel utilisateur

Marantz

Marantz BD7004 Guide de démarrage rapide

Kogan

Kogan KABRP3DWFIA Manuel utilisateur

Toshiba

Toshiba BDX2700 Manuel utilisateur

Samsung

Samsung BD-E5400 Manuel utilisateur

Samsung

Samsung BD-F5100 Manuel utilisateur

Philips

Philips BDP7100 Manuel utilisateur

Sony

Sony BDP-S185 Manuel utilisateur

Samsung

Samsung BD-FM57C Manuel utilisateur