Leviton LFD20 Manuel utilisateur

LEO™ LED Fresnel

Cat. Nos. LFD20, LFD32

User’s Guide

LEO™

CATALOG LOGIC

LFD20-30B; LFD20-50B

LFD32-30B; LFD32-50B

Fixture Wattage Color Temperature Housing

LFD: LED Fresnel 20: 200W -30: 3200K B: Black Housing

32: 320W -50: 5600K

SPECIFICATIONS

CAT. NO. LFD20 LFD32

WATTAGE 200 W 320 W

STANDBY LOAD

BEAM ANGLE 8°-60° 16°-58°

WEIGHT 19.6 lbs. (8.9 kg) 27.6 lbs. (12.5 kg)

SIZE W 11" (280mm) x H W 13.5" (342mm) x H

17.1" (435mm) x D 19.1" (485mm) x D

19.3" (490mm) 19.3" (490mm)

ELECTRICAL 100-240 VAC, 50/60Hz 100-240 VAC, 50/60Hz

WARNINGS AND CAUTIONS

• TO AVOID FIRE SHOCK OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that

power is off before installation.

• TO AVOID SERIOUS PERSONAL INJURY, always connect this product to a grounded circuit.

• To be installed and/or used in accordance with electrical codes and regulations.

• If you are unsure about any part of these instructions, consult an electrician.

SAFETY NOTES

WARNING: TO AVOID DEATH, SERIOUS PERSONAL INJURY OR PROPERTY DAMAGE:

• Do not open the housing or attempt any repairs. In the unlikely event the unit may require service

please contact Leviton Technical Support. Opening the housing or attempting to repair product will

void the warranty.

• Do not expose this product to rain or moisture. This product is for indoor use only! (IP20) When

transferring product from extreme temperature environments, (e.g., cold truck to warm humid

ballroom) condensation may form on the internal electronics of the product. To avoid causing a

failure, allow product to fully acclimate to the surrounding environment before connecting it to power.

• Do not operate this product if you see damage on the housing, lenses, or cables.

PRODUCT INTRODUCTION

LEO™ LED Fresnel is a high-performance Fresnel-style LED lighting ﬁxture that delivers a beautiful ﬂat

even ﬁeld of light in a choice of color temperatures (3200K and 5600K) with high color rendering index

(CRI 90+). The ﬁxture is fully dimmable from 0% to 100% and can be controlled manually or via DMX

controller. It also supports power linking with built-in powerCON®connectors. Virtually quiet operation

makes it ideal for use in any situation. The ﬁxture is RDM-ready for precise monitoring of the LED chip’s

performance and status to make maintenance easy.

GETTING STARTED

Thank you for choosing LEO™ LED Fresnel by Leviton®. Every LEO™ LED Fresnel has been thoroughly

tested and has been shipped in perfect operating condition. Your LEO™ LED Fresnel should include:

Power cords with alternate connectors, and, powerCON®extension cables are available.

Please contact Leviton and review product data sheets for details.

Important: Unpack the product and check the box to make sure all the parts are in the package and

are in good condition. If any of them are damaged, please contact the shipper to make a claim. If any

components are missing, please contact our Customer Service Department at 1-800-736-6682.

• Fixture

• powerCON®B connector

• Metal Color Frame 9.65" x 9.65"

(245 x 245mm) (for LFD20)

• Metal Color Frame 12" x 12"

(305 x 305mm) (for LFD32)

• Safety Guard 9.65" x 9.65"

(245 x 245mm) (for LFD20)

• Safety Guard 12" x 12"

(305 x 305mm) (for LFD32)

• User’s Guide

• Fuse, glass tube, 6A (for 110V) (for LFD20)

• Fuse, glass tube, 10A (for 110V) (for LFD32)

• Fuse, glass tube, 3A (for 220V) (for LFD20)

• Fuse, glass tube, 5A (for 220V) (for LFD32)

• Safety Cable, 31.5" (800mm) with Spring Clips

• 36"-39.5" (1m) power lead with powerCON® & PBG

(NEMA 5-15P Connector)

IDENTIFY THE PARTS

Safety Cable

Rear View

Power in

Power switch

12 mm Hole

mounting yoke

Yoke fastening

knob

Display control

knob

Fuse

DMX input

(XLR5-pin male)

Handle

LCD display

DMX output

(XLR5-pin

female)

loop out

Front View

Barn door

clip

Fresnel

Lens

Lens clips

3-Slot

accesory

runners

Vent holes

(do not block)

Vent holes

(do not block)

SAFETY NOTES

• This product contains no user-serviceable parts. Do not open the housing or attempt any repairs,

doing so will void the manufactures warranty. In the unlikely event the unit may require service please

contact Leviton technical support.

• Do not operate this product if you see damage on the housing, lenses, or cables.

• This product is for indoor use only! (IP20) To prevent risk of ﬁre or shock, do not expose this product to

rain or moisture. When transferring product from extreme temperature environments, (e.g. cold truck

to warm humid ballroom) condensation may form on the internal electronics of the product. To avoid

causing a failure, allow product to fully acclimate to the surrounding environment before connecting

it to power.

REPLACE FUSE

CAUTION:

Fuse pre-installed in BLACK fuse cover supports 220V AC Power only

Fuse pre-installed in GREY fuse cover supports 110V AC Power only

Always make sure you are connecting this product to the proper voltage in accordance

with the speciﬁcations in this manual or on the product’s speciﬁcation label.

Choose the correct fuse for your power voltage before connecting power.

Step 1: Unplug the product from power.

Step 2: Use a slotted screwdriver, push slightly and rotate counterclockwise to open the fuse cap.

Step 3: Take out the fuse cap and fuse. Put a new fuse inside the fuse cap.

Step 4: Screw the fuse cap back in place and reconnect power.

FUSE 110V/6A; 220V/3A

SLOW BLOW

OPEN LOCK

CONNECT POWER

CAUTION:

LEO™ LED Fresnel comes with a power lead terminated with a powerCON®A connector on one side,

and a PBG NEMA 5-15P connector on the other side. Other connector options are available from Leviton

or may be installed by your contractor. In addition, the ﬁxture is designed for "Feed-Thru" operation using

single power source connection at the ﬁrst ﬁxture, then, using powerCON®extensions between ﬁxtures.

The maximum load supported is 16A through the powerCON®connectors which is reduced to 15A if you

use a 15A source power connector like a NEMA 5-15P.

If creating your own powerCON®connectors, use the table below to wire the included powerCON®

B connector, or a local plug to the power lead.

Connection Wire

AC Live Brown

AC Neutral Blue

AC Ground Green / Yellow

CONNECT DMX

LEO™ LED Fresnel uses 5-pin XLR connectors for signal transmission and can be controlled via

DMX-512 protocol. The diagram below shows the ﬁxture’s XLR-5 signal ports.

Step 1: Connect the (male) 5-pin connector side of the DMX cable to the output (female) 5-pin connector

of the DMX console.

Step 2: Connect the end of the cable coming from the console which will have a (female) 5-pin connector

to the ﬁxture’s input port ("DMX IN") consisting of a (male) 5-pin connector.

Step 3: Then, proceed to connect from the output port ("LOOP") as stated above to the input of the

following ﬁxture and so on.

XLR Pin # Signal

1 common

2 data -

3 data +

4 NC

5 NC

DMX IN LOOP

XLR-5 signal ports

WARNING: TO AVOID SERIOUS PERSONAL INJURY, always connect this product to

a grounded circuit.

MOUNT FIXTURE

CAUTION:

LEO™ LED Fresnel may be mounted in any position (max. tilting +45° to -90° from horizontal); however,

make sure there is adequate room for ventilation, conﬁguration, and maintenance.

The ﬁxture comes with a hanging/mounting yoke to which you can attach mounting clamps. The bracket

has a 0.5" (12mm) hole, which is appropriate for this purpose. Make sure the clamps are capable of

supporting the weight of this product.

FIXTURE ANGLE ADJUSTMENT

The ﬁxture can be tilted up and down to position the light where it is needed.

Step 1: Loosen the yoke fastening knob, use the handle on the rear of the unit to keep the ﬁxture

steady.

Step 2: With the ﬁxture turned on, use the handle to tilt it to the desired angle.

Step 3: Tighten the yoke fastening knob.

FIELD ANGLE ADJUSTMENT

You can adjust the ﬁeld angle of the ﬁxture with the focusing knob on the rear of the unit.

To reduce the ﬁeld angle (SPOT), turn the focus dial clockwise.

To enlarge the ﬁeld angle (FLOOD), turn the focus dial counterclockwise.

Always mount this product in a safe position with adequate ventilation and away from

a heat source, at least 20" (50 cm) from adjacent surface, and no ﬂammable materials

close by the product while it is operating, at least 8" (20 cm) from adjacent surfaces.

Always connect the provided Safety Cable to the ﬁxture and a suitable anchor. The safety

cable should loop through the ﬁxture yoke and be connected to a secure attachment at

the other end.

ACCESSORIES

LEO™ LED Fresnel can accommodate many different accessories.

ACCESSORY SLOTS

CAUTION:

LEO™ LED Fresnel has 3 accessory slots in the front of the ﬁxture and is equipped with a spring-loaded

barn door clip that prevents color frames and accessories from falling out.

Step 1: Release the barn door clip by pushing it sideways while gently pulling backwards.

Step 2: Insert the media/accessories, secure with a safety cable where necessary.

Step 3: Lock the barn door clip by pushing sideways while gently pushing forward.

Accessories such as barn doors and color scrollers must be secured by safety cable to

the mounting structure.

Make sure all color / diffusion media are locked in position with the barn door clip before

hanging the ﬁxture.

Cat. No. Description Part Number

All Safety Cable (included) TA0SC-000

LFD20 8 Leaf Barn Door 9.65" x 9.65" (245 x 245mm) LFD20-BDB

LFD20 Metal Color Frame 9.65" x 9.65" (245 x 245mm) (included) LEDAC-CFB

LFD20 Safety Guard 9.65" x 9.65" (245 x 245mm) (included) LEDAC-SGB

LFD32 8 Leaf Barn Door 12" x 12" (305 x 305mm) LFD32-BDB

LFD32 Metal Color Frame 12" x 12" (305 x 305mm) (included) LFD32-CFB

LFD32 Safety Guard 12" x 12" (305 x 305mm) (included) LFD32-SGB

OPERATION

CAUTION:

LEO™ LED Fresnel will start a self-checking process when power is applied. The unit will display the

DMX address for dimming when ready to use. For standard operation, connect the ﬁxture to a power

source (100~240V AC single phase), and a DMX signal cable. The LCD Display will turn on after the

power switch is turned to "ON" position. You are now ready to set the desired conﬁguration and DMX

addresses.

You can assign a DMX channel to control dimming, cooling fan speed, LCD display-on time, built-in

effects and live/safe modes according to the DMX value on the "Menu Map". These parameters can also

be assigned through a console.

CONTROL INTERFACE

LEO™ LED Fresnel comes with a LCD Display and a control knob on the rear of the unit for control

settings:

1. LED Temperature

2. DMX dimming address

3. Built-in effects

4. Cooling Fan speed control

5. Operation Mode: Live or Safe

6. LCD display on time

7. Control mode: DMX or Manual

8. DMX dimming address setting

9. Status-bar

10. Rotary-press-knob

Do not touch this product’s housing during operation because it may be very hot if

overheated.

The maximum ambient temperature is 95˚F (35˚C). Do not operate this product at a

higher temperature.

Do not cover the ventilation holes when operating to avoid internal overheating.

Avoid direct eye exposure to the light source while the product is on.

In case of a serious operating problem, stop using this product immediately!

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Leviton Éclairage domestique

Leviton

Leviton JCC JC17071 Manuel utilisateur

Manuels Éclairage domestique populaires d'autres marques

JONATHAN Y

JONATHAN Y JYL5019A Manuel utilisateur

JONATHAN Y

JONATHAN Y JYL6007A Manuel utilisateur

Philips

Philips Ledino 31606/11/16 Manuel utilisateur

Salus

Salus UG600 Manuel utilisateur

Safavieh Lighting

Safavieh Lighting CANDRI TBL4427A Manuel utilisateur

Hunter

Hunter Bullet Spotlight Kit Manuel d'instructions

Philips

Philips Ledino 16811/87/16 Manuel utilisateur

Philips

Philips 405441213 Manuel utilisateur

Philips

Philips Halogen Light Manuel utilisateur

Pentair

Pentair GLOBRITE Manuel utilisateur

Philips

Philips 55592-30-16 Manuel utilisateur

Livoo

Livoo Night light Manuel utilisateur

Schwaiger

Schwaiger NFL45 Manuel utilisateur

FRITZ HANSEN

FRITZ HANSEN AQ01 PLUG-IN Manuel utilisateur

MOOD

MOOD CORSIN JY-16 Manuel utilisateur

Safavieh Lighting

Safavieh Lighting KREMP TBL4409A Manuel utilisateur

JONATHAN Y

JONATHAN Y JYL8019 Manuel utilisateur

XTRASUN

XTRASUN XTDEOKT1 Manuel utilisateur