Leuze IGSU 14E Manuel utilisateur

IGSU14E

Ultrasonic label fork

Leuze electronic GmbH + Co. KG

[email protected]

In der Braike 1 73277 Owen Tel.: +49 7021 573-0

We reserve the right to make changes – 2020/05/07 – 50143646

www.leuze.com•

1Figure part

> 12 s

2-7 s

+> 7 s

7-12 s

2-7 s

7-12 s

> 12 s

2-7 s

< 2 s < 2 s

–

> 7 s

HIGH

LOW

≥ 20 ms ≥ 20 ms

Intended use

The ultrasonic label forks are ultrasonic sensors for contactless detection of the

gap between two consecutive labels on a carrier tape.

NOTICE

Observe intended use!

This product is not a safety sensor and is not intended as personnel

protection.

ÄOnly allow competent persons to put the product into operation.

ÄOnly use the product in accordance with its intended use.

Function and device operation

The label material used determines the achievable precision and the reliability of

gap detection between labels.

– Light switching: signal in the label gap.

– Dark switching: signal on the label.

A Label center position

B Label run

ÄTo achieve a high switching accuracy, place the label tape on the lower fork

with slight tension.

ÄAlign the label tape with the "Label center position" marking.

Overview of the operating structure via the teach and minus buttons

A Standard function

Normal operation after switch-on

B easyTeach (while the label tape is passing through)

(2-point calibration on carrier and label)

C Static teach (on the label carrier without transport)

(1-point calibration on carrier)

D Set switching behavior (light/dark switching)

E Deactivate/activate the

ALC

(Auto Level Control) function

(automatic optimization of the switching threshold)

F Manual locking/unlocking of the buttons on the device

IGSU14E standard functions

During operation the sensor is always in this function.

The sensor detects label gaps with high precision and speed.

This is indicated by the yellow OUTLED and the switching output.

ONLED

green

Constantly ON when operating voltage is applied.

OUTLED

yellow

Indicates the switching signal.

LED is ON if the sensor detects label gaps.

The display is independent of the output setting.

WARNLED

continuous red

light

OFF: error-free operation.

ON: teaching error caused by unfavorable label material

ON:

ALC

(Auto Level Control) function is faulty.

ALCLED

yellow

ALC

(Auto Level Control) function is active.

easyTeach while the label tape is passing through (dynamic)

During the

easyTeach

process, a two-point calibration is performed on the carrier

and the label.

NOTICE

With respect to detection reliability, the

easyTeach

process is gener-

ally to be preferred over the static teach process.

Preparation: Insert label tape into the sensor.

ÄPress the teach button until the green ON LED and the yellow OUT LED flash

synchronously.

ÄRelease the teach button.

ÄAllow the label tape to advance through the sensor at a maximum speed of

50m/min.

ðThe sensor indicates the belt transport by a more rapid synchronous

flashing of the green ON LED and yellow OUT LED.

– If sufficient teach values are determined, the sensor automatically terminates

the teach event and goes into standard mode.

The transport of the label tape can be stopped immediately.

– The number of labels to be transported is always based on the material com-

bination. From experience, approximately 2-10 labels should be advanced

through the sensor.

– If the teach event is faulty (e.g., unfavorable material combination, uneven

transport, jittering during transport), the red WARNLED illuminates and the

warning output (if present for the sensor model) is activated.

If the fault cannot be rectified, e.g., via the

easyTune

function, the label ma-

terial cannot be detected with the device.

Static teach on the label carrier without transport

With the static teach process, a one-point calibration is performed on the blank

carrier. This process is especially advantageous because no labels are lost while

teaching.

Preparation: depending on the label size, pull off one or more labels from the car-

rier and insert the blank area into the sensor.

ÄPress the teach button until the green ONLED and the yellow OUTLED flash

alternately.

ÄRelease the teach button.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Leuze Accessoires

Leuze

Leuze ODS 96 M/V Instructions de montage

Leuze

Leuze ESB2 Series Manuel utilisateur

Leuze

Leuze ODSL 30 Manuel utilisateur

Leuze

Leuze IGSU 14E SD Manuel utilisateur

Leuze

Leuze PRK 55 Ex Series Manuel utilisateur

Leuze

Leuze DCR 200i Manuel utilisateur

Leuze

Leuze GS63B/6.3-S8 Manuel utilisateur

Leuze

Leuze HT25CL2 Manuel utilisateur

Leuze

Leuze KRT18BW Manuel utilisateur

Leuze

Leuze GSX14E Manuel utilisateur

Leuze

Leuze BPS 8 SM 102 Manuel utilisateur

Leuze

Leuze LRS Manuel de la liste des pièces

Leuze

Leuze KRT3CM Series Manuel utilisateur

Leuze

Leuze BPS 34 Series Manuel de la liste des pièces

Leuze

Leuze MLDSET-M1 Manuel utilisateur

Leuze

Leuze GSU12 Manuel utilisateur

Leuze

Leuze LBK S-01 Manuel utilisateur

Leuze

Leuze LES 36 Series Manuel utilisateur

Leuze

Leuze HTU330 Series Manuel utilisateur

Leuze

Leuze SET-AC Manuel utilisateur

Leuze

Leuze DDLS 170 Manuel de la liste des pièces

Leuze

Leuze GSU14E Manuel utilisateur

Leuze

Leuze KRT18BW Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur