Leuze electronic IT 1911i Manuel utilisateur

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0

[email protected] • www.leuze.com

We reserve the right to make changes •

Very sturdy hand-held scanner for

2D-codes and bar codes

Transmission to base station via Bluetooth

class 1 V2.1

Very large range with high resolution and

improved decoding

Robust trigger button

Acoustic signal, LED and vibration alarm

following successful reading

RS 232, USB and PS/2 interface

Operating temperature from -20°C through

50°C

Degree of protection IP 65

5 V

Accessories

TTL-RS 232 cable

Part no. 50114517

PS/2 cable

Part no. 50114519

USB cable, 3m

Part no. 50114521

USB helix cable, 5m

Part no. 50114523

Power supply unit for Base IT 19x1i

Part no. 50123862

IP 65

Dimensioned drawing

Electrical connection

for RS 232 cable

for USB cable

for PS/2 cable

9-pin Sub-D Signal Base for IT 19x1i RJ41

2TXD4

3RXD5

5GND3

7CTS6

8RTS8

95VDC7

USB type A Signal Base for IT 19x1i RJ41

15VDC7

2Data-10

3Data+9

4GND3

Mini DIN connector Mini DIN socket Signal Base for IT 19x1i RJ41

1-PCData4

22NC

33GND3

445VDC7

5-PCClock5

66NC

-1KBdata8

-5KBclock6

IT 1911i / IT 1981i 2D-code hand-held scanner with Bluetooth for industrial use

IT 1911i / IT 1981i - 03

Specifications and description

en 03-2015/09 50123747-02

IT 1911i / IT 1981i - 03 2015/09

Specifications

Reading field

Electrical data IT 19x1i … Base for IT 19x1i

Operating voltage UB3.7VDC internal battery 4.5 … 5.5VDC

Power consumption max. 5W @ 5VDC

Li-ion battery

Capacity 2,000mAh

Max. number of scans 50.000

Max. operating time 14h at 1scan/s

Charging time at 9VDC 4.5h for complete charge following complete discharge

Radio transmission

Frequency 2.4 … 2.4835GHz (ISM band)

frequency hopping, Bluetooth ® V2.1, Class 1

Typ. operating range 100m

Transmission speed up to 1Mbit/s

Interfaces

Interface type RS 232, PS/2 and USB

Trigger via button or serial command

Types of codes

2D-codes Data Matrix ECC 200, MaxiCode, PDF417, MicroPDF, QR Code, Az-

tec, Aztec Mesas, Code 49, EAN/UCC Composite

Bar codes 2/5 Interleaved, Code 39, Code 128, Code 93, Codabar, UPC/EAN,

Codablock, GS1 Databar

Optical data

Optical system high-resolution pixel array 838x640

Symbol contrast PCS 20% minimum

Light source integrated diffuse LED, wavelength 617nm ± 18nm

Read direction omnidirectional, various tilt and rotational angles up to 45°

Alignment aid laser pattern 630 … 680nm; IEC 60825-1:2007 Class 2

Mechanical data IT 19x1i… Base for IT 19x1i

Weight IT 1911i…: approx. 380g,

IT 1981i…: approx. 420g

290g (without cable)

Dimensions 133 x 75 x 195mm 250 x 103 x 65mm

Shock resistance 50 falls from a height of 2m 50 falls from a height of 1.2m

Environmental data

Ambient temp. (operation) -20°C … +50°C -20°C … +50°C

Ambient temp. (storage) -40°C … +70°C -40°C … +60°C

Relative humidity 0 … 95% (non-condensing) 0 … 95% (non-condensing)

Degree of protection IP 65 IP 51

0 200 400 600100 300 500 700 800

7.5 Mil

(0.191 mm)

Code 39

PDF 417

Data Matrix

QR Code

UPC 13 Mil

(0.330 mm)

20 Mil

(0.508 mm)

6.7 Mil

(0.170 mm)

10 Mil

(0.254 mm)

20 Mil

(0.508 mm)

Code 39

IT 1911i ER-3

Typ. reading distance depending on the code module [mm]

0 4000 8000 120002000 6000 10000 14000 16000

7.5 Mil

(0.191 mm)

Code 39

Data Matrix

UPC 13 Mil

(0.330 mm)

20 Mil

(0.508 mm)

100 Mil

(2.540 mm)

10 Mil

(0.254 mm)

100 Mil

(2.540 mm)

Code 39

IT 1981i FR-3

Typ. reading distance depending on the code module [mm]

Tables

Remarks

Hand-held scanner with inte-

grated decoder for high-con-

trast codes suitable for

industrial use.

Data transmission via config-

urable RS 232 interface.

Or keyboard-wedge opera-

tion via PS/2 or USB inter-

face.

For a functional unit, an

IT 19x1i hand-held scanner

and a Base for IT 19x1i base

station as well as a power

supply unit and correspond-

ing cable must be ordered.

Bluetooth is a trademark owned by

Bluetooth SIG, Inc., U.S.A. and

licensed to Honeywell.

Operate in accordance with

intended use!

The product may only be put into

operation by competent persons.

Only use the product in accor-

dance with the intended use.

IT 1911i / IT 1981i

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 IT 1911i / IT 1981i - 03

[email protected] • www.leuze.com

Order guide

2D-code hand-held scanner (Extended Range optics with large operating range) Part no.

IT 1911i ER-3 with Bluetooth data transmission 50122434

2D-code hand-held scanner (Full Range optics with very large operating range) Part no.

IT 1981i FR-3 with Bluetooth data transmission 50130495

Base station for 2D-code hand-held scanner with Bluetooth data transmission Part no.

Base for IT 19x1i with RS 232, PS/2 and USB interface 50122431

IT 1911i / IT 1981i 2D-code hand-held scanner with Bluetooth for industrial use

IT 1911i / IT 1981i - 03 2015/09

Laser safety notices

ATTENTION, LASER RADIATION – LASER CLASS 2

Never look directly into the beam!

The device fulfills the EN 60825-1:2007 safety regulations for a product in laser class 2 as well as the U.S. 21 CFR 1040.10 regulations

with deviations corresponding to "Laser Notice No. 50" from June 24th, 2007.

Never look directly into the laser beam or in the direction of reflecting laser beams!

If you look into the beam path over a longer time period, there is a risk of injury to the retina.

Do not point the laser beam of the device at persons!

Interrupt the laser beam using a non-transparent, non-reflective object if the laser beam is accidentally directed towards a person.

When mounting and aligning the device, avoid reflections of the laser beam off reflective surfaces!

CAUTION! Use of controls or adjustments or performance of procedures other than specified herein may result in hazardous light

exposure.

Observe the applicable statutory and local laser protection regulations.

The device must not be tampered with and must not be changed in any way.

There are no user-serviceable parts inside the device.

Repairs must only be performed by Leuze electronic GmbH + Co. KG.

NOTICE

Laser information and warning signs firmly attached to the device.

ALaser aperture

BLaser warning sign

CLaser information sign with laser parameters

A CA

IT 1911i / IT 1981i

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 IT 1911i / IT 1981i - 03

[email protected] • www.leuze.com

Switching off the computer

Information on switching off and shutting down the connected computer - which must always be performed before connecting

peripheral devices, such as a scanner - can be found in the appropriate operating instructions for your computer.

Connecting the base station

Shown in the adjacent figure are the locations for installing the cables on

the base station. The individual installation steps are described in the fol-

lowing.

1.To secure the interface cable to the base station, proceed as follows:

plug the RJ 41 connector into the socket on the bottom of the base sta-

tion until the cable clicks into place.

2.Connect the interface cable to the appropriate connection socket on

the computer.

3.You may need a power supply unit for supplying voltage if you would

like to charge the hand-held scanner via the base station or use an

RS 232 interface. Use the pin assignments (see "Electrical connection"

on page 1) to select the appropriate cable for your application.

4.Connect the power supply unit to the power socket.

5.Use the code for the respective application to configure the hand-held

scanner, see chapter "Parameterization".

6.Check the operational readiness of the scanner by pointing the scan-

ning surface towards a flat surface and pulling the trigger. A red laser

pattern as well as the red illumination should now be visible. Now scan

a sample label.

The scanner emits an audible signal to confirm that the label has been

read; if necessary, the data are now passed on to the computer.

Notice!

To charge the hand-held scanner, the power supply unit must be plugged in

and the hand-held scanner placed in the base station.

Parameterization

The hand-held scanner can always be configured using bar codes. To do this, the bar code must first be selected on the package

insert and then the trigger actuated in order to read the code. The configuration is then immediately accepted and executed.

Several of the most important configurations are listed in the following.

A second option is to configure the hand-held scanner with the USB and RS 232 interfaces with the aid of the EZ Config PC

program. You can download and install this program from our homepage at www.leuze.com.

The program can be used to make settings and transfer them to the hand-held scanner. The configuration can also be stored so

that it can be reused at a later time.

More information can also be found in the user's guide.

The standard applications are described and summarized below.

Notice!

Additional information on the device and short instructions can be found on the Internet at www.leuze.com.

Connection for power

supply unit

Connection for interface

cable (RJ 41 socket)

IT 1911i / IT 1981i 2D-code hand-held scanner with Bluetooth for industrial use

IT 1911i / IT 1981i - 03 2015/09

Resetting the IT 1911i / IT 1981i to factory settings

To reset all parameters to factory settings, scan the adjacent

bar code.

Attention!

All settings are lost!!!

Return the hand-held scanner to the base station to apply the settings. This procedure is concluded with audible confirmation

signals.

You may then continue making settings or operation of the device.

Trigger

To activate the read process, a trigger signal is to be sent via the serial RS 232 interface or USB interface (COM port emulation

only). The command is to be sent at the set baud rate, parity, and data and stop bits.

The command for activation is: SYN T CR ASCII decimal values: 022; 084; 013

To cancel read readiness, send a deactivation.

The command for deactivation is: SYN U CR ASCII decimal values: 022; 085; 013

Following a successful read operation, the hand-held scanner deactivates itself.

The second option is activation via the built-in trigger button.

Configuration for the Leuze standard protocol

Scan the adjacent 2D-code.

The hand-held scanner is set to the following transmission parameters:

RS 232 transmission with 9,600 baud, 8 data bits, 1 stop bit, no parity, prefix <STX>,

postfixes <CR><LF>.

Return the hand-held scanner to the base station to apply the settings. This procedure

is concluded with audible confirmation signals.

Notice!

To charge the hand-held scanner, the power supply unit must be plugged in

and the hand-held scanner placed in the base station.

IT 1911i / IT 1981i

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 IT 1911i / IT 1981i - 03

[email protected] • www.leuze.com

Connecting the IT 1911i / IT 1981i to the serial PC interface

With TTL-RS232 cable (part no. 50114517)

Required parts:

1x IT 1911i ER-3 or IT 1981i FR-3

1x 50122431 Base for IT 19x1i

1x 50114517 KB 232-1 IT 190x

1x 50123862 Power supply unit for Base for

IT 19x1i

Notice!

Cable KB 232-1 IT190x (part no. 50114517)

uses TTL-level (0V…5V) for data transmission.

As an alternative to this, cable KB 232-

2 IT190x (part no. 50115105) can be used.

This cable works with the regular RS232 level

(-12V…+12V) and therefore features a higher

interference rejection. Both cables are con-

nection compatible.

Procedure:

1.Switch off the PC.

2.Connect the interface cable to a free COM port

(RS 232) on the computer and to the base station.

3.Plug one end of the power supply unit cable into the

base station and the other end into a free power

socket.

4.Switch the PC back on.

5.Scan the adjacent bar code.

The hand-held scanner is set to the following transmission parameters:

RS 232 transmission with 115,200 baud, 8 data bits, 1 stop bit, no parity, postfixes <CR><LF>.

6.Return the hand-held scanner to the base station to apply the settings. This procedure is concluded with optical confirmation

signals (green LED on the base station).

7.If necessary, adjust the transmission parameters of the used COM port to those of the hand-held scanner.

Attention!

We recommend connecting the base station directly to a PC or to the MA 21 or MA 41… connection units. If connect-

ing to other components, please note that a voltage level range of 0 … +5V (TTL level) is maintained on the data lines!

Notice!

To charge the hand-held scanner, the power supply unit must be plugged in

and the hand-held scanner placed in the base station.

IT 1911i / IT 1981i 2D-code hand-held scanner with Bluetooth for industrial use

IT 1911i / IT 1981i - 03 2015/09

Connecting the IT 1911i / IT 1981i to the MA 2xxi

Required parts:

1x IT 1911i ER-3 or IT 1981i FR-3

1x 50122431 Base for IT 1911i

1x 50114517 KB 232-1 IT 190x

1x 50123862 Power supply unit for Base for IT 1911i

1x 50113397 KB JST-HS-300

1x MA 2xxi for the respective fieldbus system

Procedure:

1.Connect cable KB JST-HS-300 to the system connector on the MA 2xxi.

2.Connect the interface cable to cable KB JST-HS-300. Connect the interface cable and the

power supply unit to the base station (see "Connecting the IT 1911i / IT 1981i to the serial

PC interface").

3.Scan the adjacent 2D code.

The hand-held scanner is set to the following transmission parameters:

RS 232 transmission with 9,600 baud, 8 data bits, 1 stop bit, no parity, postfixes

<CR><LF>.

4.Return the hand-held scanner to the base station to apply the settings. This procedure is

concluded with audible confirmation signals.

Notice!

To charge the hand-held scanner, the power supply unit must be plugged in

and the hand-held scanner placed in the base station.

IT 1911i / IT 1981i

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 IT 1911i / IT 1981i - 03

[email protected] • www.leuze.com

Connecting the IT 1911i / IT 1981i to the MA 21

Required parts:

1x IT 1911i ER-3 or IT 1981i FR-3

1x 50122431 Base for IT 19x1i

1x 50114517 KB 232-1 IT 190x

1x 50123862 Power supply unit for Base for IT 19x1i

1x 50035421 KB 021 Z

1x 50030481 MA 21 100

Pin assignments KB021 Z:

Core color: Signal Terminal in the MA 21:

Brown (RXD) 26

White (TXD) 27

Blue (GND) 28

Red (VCC) 

Black (GND) 

Bare (shield) (PE) 21

Procedure:

1.Connect cable KB 021 Z to the MA 21… acc. to the above pin assignments.

2.Connect the interface cable to cable KB 021 Z. Connect the interface cable and the power

supply unit to the base station (see "Connecting the IT 1911i / IT 1981i to the serial PC inter-

face").

3.Scan the adjacent 2D code.

The hand-held scanner is set to the following transmission parameters:

RS 232 transmission with 9,600 baud, 7 data bits, 1 stop bit, even parity, postfixes

<CR><LF>.

4.Return the hand-held scanner to the base station to apply the settings. This procedure is

concluded with audible confirmation signals.

Notice!

To charge the hand-held scanner, the power supply unit must be plugged in

and the hand-held scanner placed in the base station.

IT 1911i / IT 1981i 2D-code hand-held scanner with Bluetooth for industrial use

IT 1911i / IT 1981i - 03 2015/09

Connecting the IT 1911i / IT 1981i to the PS/2 interface

The operation of the hand-held scanner in keyboard emulation mode is described in this section. With this operating mode, a PC

keyboard is emulated. The read data are written directly into the currently activated program. The data can thereby be further

processed in all standard programs.

Required parts:

1x IT 1911i ER-3 or IT 1981i FR-3

1x 50122431 Base for IT 19x1i

1x 50123862 Power supply unit for Base for

IT 19x1i

1x 50114519 KB PS2-1 IT 19xx

Procedure:

1.Switch off the PC.

2.Disconnect the keyboard.

3.Connect the cable for the base station between the

keyboard and the PC.

4.Switch the PC back on.

5.Scan the 2D code shown below.

6.Return the hand-held scanner to the base station

to apply the settings. This procedure is concluded

with audible confirmation signals.

Notice!

To charge the hand-held scanner, the power supply unit must be plugged in

and the hand-held scanner placed in the base station.

Disconnect

IT 1911i / IT 1981i

Autres manuels pour IT 1911i

Ce manuel convient aux modèles suivants

Autres manuels Leuze electronic Lecteur de codes-barres

Leuze electronic

Leuze electronic BCL 22 SB Manuel de la liste des pièces

Leuze electronic

Leuze electronic IT 1911i Manuel de la liste des pièces

Leuze electronic

Leuze electronic BCL 21/22 Manuel de la liste des pièces

Leuze electronic

Leuze electronic BPS 37 Manuel de la liste des pièces

Leuze electronic

Leuze electronic BCL 248i Manuel utilisateur

Leuze electronic

Leuze electronic BCL348i Manuel de la liste des pièces

Leuze electronic

Leuze electronic BPS 307i Manuel utilisateur

Leuze electronic

Leuze electronic IT 1910i Manuel de la liste des pièces

Leuze electronic

Leuze electronic IT 1900 Manuel utilisateur

Leuze electronic

Leuze electronic BCL 8 S 2 Series Manuel utilisateur

Leuze electronic

Leuze electronic BCL 338i Manuel utilisateur

Leuze electronic

Leuze electronic BCL 608i Manuel utilisateur

Leuze electronic

Leuze electronic BCL358i Manuel de la liste des pièces

Leuze electronic

Leuze electronic BCL558i Manuel de la liste des pièces

Leuze electronic

Leuze electronic BCL 95 Manuel utilisateur

Leuze electronic

Leuze electronic BCL308i Manuel de la liste des pièces

Leuze electronic

Leuze electronic DCR 55 Manuel utilisateur

Leuze electronic

Leuze electronic HFM 3500D Manuel utilisateur

Leuze electronic

Leuze electronic BCL500i series Manuel de la liste des pièces

Leuze electronic

Leuze electronic BCL300i Manuel utilisateur

Leuze electronic

Leuze electronic BCL500i series Manuel de la liste des pièces

Leuze electronic

Leuze electronic BCL 90Manual Manuel utilisateur

Leuze electronic

Leuze electronic 1910i Manuel de la liste des pièces

Leuze electronic

Leuze electronic IT 4820 Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur