Letscom ID132Color HR Manuel utilisateur
ID132Color HR
Fitness Tracker
User Manual
Thank you for purchasing our products. This manual addresses
the safety guidelines, warranty and operating instructions.
Please review this manual thoroughly before operating your
device.
What’s is the box ------------------------------
USB Charging ---------------------------------
Install and Wear Your Device -----------------
Smart Phone System Requirement -----------
Download the APP ----------------------------
Pair the Device --------------------------------
Touch Key -------------------------------------
Waking a Dimmed Screen --------------------
Main Functions --------------------------------
Function Introduction -------------------------
Basic Specifications ---------------------------
Electronic Information Products ---------------
Poisonous and Harmful Statement
FAQs -------------------------------------------
SAFETY AND WARRANTY --------------------
Table of Contents
01
02
03
03
03
04
05
05
06
07
15
16
16
19
1
What’s is the box?
Fitness tracker (ID132Color with bands)
Assemble/Dissemble & charging instruction card
User manual
User manual
ID132Color HR
Bands
*OYGYYKSHRKGTJ)NGXMOTM
2
1
3
Insert the built-in USB plug with metal pins into a USB
charger for charging.
Remove the tracker body from the power supply once fully
charged. (Device will automatically boot up once fully
charged. )
Red indicator is on during
charging.
Red indicator is off when
it is fully charged.
Gently pull the bands off the tracker body following the
direction of the arrow.
DO NOT pull the bands horizontally
OPEN
Assemble/Dissemble &
charging instruction card
ID132Color HR
Fitness Tracker
User Manual
Thank you for purchasing our products. This manual addresses
the safety guidelines, warranty and operating instructions.
Please review this manual thoroughly before operating your
device.
12
USB Charging
Please charge your new device for at least
10 minutes to have it activated before initial
use.
In case that device is under low battery, connect the device host
to an adapter for charging. Device will automatically boot up once
fully charged. Remove the device host from the power supply
once fully charged.
USB charger requirement: DC USB port (5V-500mA)
Charging time: 1-2hr(s)
2
The red indicator is on when the device is properly charged.
If not, check the direction of the device's charging plug and
move to the correct direction, as shown below.
3
Insert the charging plug of the host into the USB port for
charging. Make sure the pins on the charging plug contact
those in the USB port.
Wear: Wear the device on your wrist horizontally, about 2cm to
carpal, the same way as wearing a watch.
Download "VeryFitPro" APP for Android and iOS
devices.
Option 1: Search for "VeryFitPro" in APP store or Google
Play and download to your smartphone.
Download the APP
Install and Wear Your Device
Smart Phone System Requirement
iOS 8.0 & above
Android 4.4 & above
Bluetooth 4.0 & above
3
Install: Plug the host into the
slots of each strap.
4
Notes:
This fitness tracker requires iOS 8.0 & above or Android 4.4
& above system.
"VeryFitPro" APP is only compatible with smartphones.
Option 2: Searching the QR code, scan and download APP.
Use the QR code Scan tool to scan the following QR code,
open the link and follow the instructions to download APP.
Tip: In case of problems when opening the link, copy the link
and open it in a browser.
VeryFitPro
iOS Android
1）Enable Bluetooth before binding the device.
2）Open "VeryFitPro" APP on your smartphone and tap on
searching devices.
3）Select "ID132Color HR" in the list of found devices, tap on
"ID132Color HR" to connect the device to your smartphone.
Pair the Device
(If failed searching the device, please
tap on the touch key to wake the
device (screen lights on), then start
searching with your smartphone one
more time.)
4) Tap and hold the touch key of the
tracker as instructed in APP until the
tracker vibrates and connect to your
smartphone to complete the pairing.
((
))
Touch Key
will be cleared. If the device is
unbound under Bluetooth
disconnected state, the APP
will set the settings back to
default, but the data on the
device will not be cleared.
smartphone at a time. During
connecting please confirm
there are no other
smartphones nearby.
ID132Color HR
Select the device in the
smartphone searching list
5
After the first successful binding, the main
screen is as shown on the left.
Display
Note: This is a non-touch screen,
please use the touch key to choose
different functions.
Touch Key
Notes:
After the first successful searching and binding, if you enable
the Bluetooth function of the smartphone afterwards, the
device will automatically search and link back to the
smartphone it has bound.
If the device is unbound under Bluetooth connected state, the
APP will set the settings back to default. All data on the device
Waking a Dimmed Screen
When you’re not using ID132Color HR, the display is off. To
wake it up:
Note:
The screen brightness can be adjusted from Level 1 to
save your settings.
6
Ȥ:"Walk Mode", "Run Mode" and "Bike Mode" are displayed
on the device screen by default. You can set up to 3
different sports modes from 14 sports modes to display on
Ȥ:"Alarm Mode" is displayed on the device screen only
when "Alarm Alert" is ON in the APP.
Main Functions
will display time and steps.
display the main screen.
Main Screen
Heart Rate Mode Walk ModeȤStep Mode
Alarm ModeȤ
Run Mode Bike Mode
Main Screen
S
at
25
=GRQ
8[T (OQK '3
3UT
Function Introduction
1. Step Mode
1) Hold the touch key for 2s to view detailed step data.
2) Tap on the touch key to flip through detailed step
data.
3) Tap on the touch key to go to the next mode:
Heart Rate Mode.
2. Heart Rate Mode
7
Note:
You can go to the APP to set you sports target
("User" "Target Setting"). When you reach your
sport target, the device vibrates and the screen
displays:
Tap on the touch key to go back to the main screen.
After entering the heart rate interface for 1s, the device will
start monitoring the heart rate automatically. Before the correct
data is detected, the device shows " " ; after the correct
data is detected, it shows specific data.
Measuring
Tap on the touch key to go to the next mode: Walk Mode.
3. Walk Mode
1) Hold the touch key for 2s to start
the walk mode.
During exercise, tap on the touch key to flip through the
exercise data.
8
Tap on the touch key to flip through the exercise data.
3) Tap on the touch key to go to the next mode: Run Mode.
Note:
Data of exercises less than 1 minute will not be saved.
2) Hold the touch key for 2s to quit the walk mode.
The following data is displayed after the exercise is ended:
=GRQ
Table des matières
Autres manuels Letscom Suivi de forme physique
