Leitner ACS Manuel utilisateur

Table des matières

Autres manuels Leitner Accessoires automobiles

Leitner

Leitner ACS ROOF ROOF FOR ACS FORGED / CLASSIC Manuel utilisateur

Leitner

Leitner ACS ROOF GEARPOD roof Manuel utilisateur

Leitner

Leitner 00-JBRTT-1389 Manuel de programmation

Leitner

Leitner ACS FORGED Manuel utilisateur

Leitner

Leitner TRAKLOK gear pod XL Manuel utilisateur

Leitner

Leitner ACS ROOF Manuel utilisateur

Leitner

Leitner FORD SUPER DUTY 2017-UP Manuel utilisateur

Leitner

Leitner ACS TONNEAU Manuel de programmation

Leitner

Leitner ACS FORGED Manuel de programmation

Leitner

Leitner TRAKLOK gear pod Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur

Rev. A 1-2-2015 PAGE 1 OF 2

BEFORE INSTALLATION

1) READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

2) CLEAN INSTALATION AREA

3) MAKE SURE ALL TOOLS ARE AVAILABLE FOR INSTALL.

APPLICABLE MODELS:

ALL

Leitner Designs

25675 Taladro Circle Unit E

Mission Viejo, CA 92691

www.leitnerdesigns.com

TORQUE WRENCH

WITH 13MM DEEP

SOCKET

ACS Roof Top Tent Bracket instructions

1

PACKAGE CONTENTS

REMOVE CROSS BAR PAD AND ADJUSMENT KNOBS

1) REMOVE THE ENCAP AND RUBBER PAD FROM THE

CROSS BAR EXTRUSION. (FIG 1)

2) REMOVE THE FOUR ADJUSTMENT KNOBS AND

REPLACE WITH THE FOUR M8 LOCKNUTS SUPPLIED

IN KIT. MAKE SURE THE CROSS BEAMS ARE AS FAR

APPART AS POSSIBLE. TIGHTEN M8 LOCK NUTS TO

16 LB-FT (FIG 2)

M8 X 20 cap screw

(QTY.4)

M8 T-Bolt

(QTY.8)

M8 locknut

(QTY.16)

RTT Bracket

(QTY.4)

TOOLS REQUIRED

(fig 1)

(fig 2)

Rev. A 1-2-2015 PAGE 2 OF 2

1) ATTACHE TWO RTT BRACKETS TO THE INSIDE

FRONT AND INSIDE REAR CROSS BEAMS USING 8

T-BOLTS. LOSSLY TIGHTEN WITH M8 LOCKNUTS

SO THAT THE BRACKETS CAN STILL SLIDE. (FIG

3)

2) ADJUST THE BRACKEST AS SHOWN. THE

BRACKETS ARE STILL LOSE AND WILL BE

ADJUSTED IN A FUTURE STEP. (FIG 4)

3) YOUR ROOF TOP TENT SHOULD HAVE SHIPPED

WITH 4 SLIDE PLATES. INSTALL THE SUPPLIED M8

X 20 SCREWS INTO THE SLIDE PLATE AND

INSTALL TWO INTO EACH TENT MOUNTING RAIL.

(FIG 5)

4) USING A FORKLIFT (RECOMMENDED) OR 3 OF

YOUR STRONG FRIENDS LIFT THE ROOF TOP

TENT ONTO THE TOP OF THE RACK.

5) LIFT EACH CORNER OF THE TENT AND POSITION

THE M8 X 20 CAP SCREWS INTO THE HOLE ON

THE RTT MOUNTING BRACKET. LOOSLY TIGHTEN

THE M8 NUTS ONTO THE M8 X 20 CAP SCREWS.

(FIG 6)

6) CAREFULLY WALK AROUND THE VEHICLE AND

MAKE SURE THE TENT IS CENTERD ON THE RACK.

7) TIGHTEN ALL THE M8 LOCKNUTS TO 16IN-LB.

8) IS RECOMMENDED THAT YOU CHECK THE

TORQUE OF ALL THE BOLTS ON THE RACK AND

TENT FREQUENTLY TO INSURE EVERYTHING IS

TIGHT.

..

ATTACH RTT BRACKETS

1

(fig 4)

(fig 3)

M8 nut

T-bolt

RTT brackets

shown in

installed position

(fig 5)

M8 X 20

cap screw

Tent mounting

Rail

Slide plate

(fig 6)

M8

LOCKNUT