leisurecraft Cedar Panoramic Barrel Sauna Manuel utilisateur
View the assembly process
tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com
09/2023
Requirements:
2 People (recommended)
•Carpenter’s Hammer
•Step Ladder
•Cordless Drill (we supply the bit)
•Tape Measure
Carpenter’s Level
•Rubber Mallet
•¾” open end, socket, or crescent wrench
Cedar Panoramic Barrel Sauna
Assembly Instructions
Index
Base Preparation
Barrel Assembly
Adding a spacer to the Top Stave
Making a Top Stave Narrower
Flat Floor Installation
Standard Bench Installation
Signature Bench Installation
Lounge bench Installation
Dome Bench Installation
Electric Heater Installation (Option)
Wood Heater Installation (Chimney out the top) (Option)
Vent Kit Installation
Bevel Siding Installation
Asphalt Shingle Roof Installation
Cove Installation
Care & Maintenance
Warranty
tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com
Manufactured by:
2
Cedar Panoramic Barrel Sauna
Assembly Instructions
Sauna Base Preparation
Make sure the base for your sauna is level with a slight slope to the back for drainage.
A solid base for your sauna is recommended and can be made from any of the following.
Concrete Pad Wood Deck
Crushed Stone Patio Stone/Paver Blocks
It is recommended to build a base larger than required to provide a sitting area for cooling
off during your sauna session.
tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com
Manufactured by:
3
Cedar Panoramic Barrel Sauna
Assembly Instructions
Barrel Assembly
“The Panoramic Acrylic Dome cannot be exposed to high temperatures for more than 6
hours at a time. Maximum Temperatures at the acrylic dome not to exceed 100 degrees
Celsius (212 degrees Fahrenheit).”
tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com
Manufactured by:
Locate bottom stave (convex on either side).
Center the stave onto the cradle and measure 5 ½”
(14cm) from the end of the stave to the edge of the
cradle.
Secure the stave with a 2 ½” (76mm) screw.
Ensure that the stave is square and add 3 more 3”
(64mm) screws into each corner of the cradle.
*Always ensure that you have the correct screw
length so that there will be enough thread to hold,
and especially, so that the screw does not go all the
way through the material and come out the other
side.
4
Cedar Panoramic Barrel Sauna
Assembly Instructions
Place the cradles onto the sauna base.
Repeat at opposite end of the sauna.
Place 3 staves on either side of the bottom stave and
align the grooves.
*Please note that depending on the sauna and
options chosen, The dado cuts may bot be in the
same location as per the picture.
tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com
Manufactured by:
Keep the dado grooves in line with the correctly
positioned bottom stave.
Make sure there are no gaps between the edges of
the staves, and that the groove line for the dome is
lined up perfect.
Tap the staves tight together with a rubber mallet.
Place 2- 2 ½” (64mm) screws into the 3rd stave on
either side lining up with the cradle underneath.
Do not go all the way through the stave at this point.
Repeat at opposite end.
5
Cedar Panoramic Barrel Sauna
Assembly Instructions
Attach the stave supports using 2 ½” (64mm) screws
making sure they are flush with the curve of the
cradle.
*These supports are temporary to assist in the
installation of the acrylic dome and will be removed
later in the assembly process .
tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com
Manufactured by:
Using 2 people, gently place the acrylic dome into the
groove at the back of the sauna.
Use the top stave (concave on either side) to go from
the front wall to the dome to help stabilize the sauna.
6
Cedar Panoramic Barrel Sauna
Assembly Instructions
Grab the door and place it in the grooves on the front
wall.
Ensure the logo is facing inwards.
Using a level and rubber mallet, tap the door until it is
centered and level.
Install Front wall half moon panels.
Ensure the bench support is facing inwards.
*Please note that depending on the sauna and
options chosen, Front and Rear half moon panels may
or may not have windows.
tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com
Manufactured by:
Secure the half wall panel to the Door Panel using
2 ½” (64mm) screws in the pre drilled holes at the top
and bottom.
Repeat the process with the other Front wall half
moon panel.
Please note:
Panels may be not be exact size to middle wall.
7
Cedar Panoramic Barrel Sauna
Assembly Instructions
Center the half moon panels vertically on the middle
wall and secure in place.
tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com
Manufactured by:
Secure every 2nd stave on the bottom of the sauna
with the provided nails to hold staves in place.
( If required)
* Once past the middle point of sauna, nails should
no longer be needed.
8
Continue adding staves on either side of the sauna a
few at a time, alternating sides.
Use the rubber mallet to finesse into place.
When installing the staves, tap tightly together
while leaving as much of a gap as possible
between stave and wall using the pencil line as a
guide as in picture.
* This will make the tightening of the bands easier.
Cedar Panoramic Barrel Sauna
Assembly Instructions
Center the half moon panels vertically on the middle
wall and secure in place.
tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com
Manufactured by:
Secure every 2nd stave on the bottom of the sauna
with the provided nails to hold staves in place.
( If required)
* Once past the middle point of sauna, nails should
no longer be needed.
9
Continue adding staves on either side of the sauna a
few at a time, alternating sides.
Use the rubber mallet to finesse into place.
When installing the staves, tap tightly together
while leaving as much of a gap as possible
between stave and wall using the pencil line as a
guide as in picture.
* This will make the tightening of the bands easier.
Cedar Panoramic Barrel Sauna
Assembly Instructions
Continue adding staves on either side of the sauna a
few at a time, alternating sides.
Use the rubber mallet to finesse into place.
tel: 888-923-9813 | info@leisurecraft.com| web: www.leisurecraft.com
Manufactured by:
Continue adding staves until you reach the top of the
sauna.
At this point, Remove the top stave and put it aside
while continuing to add staves on both sides to the
top.
When you reach the top, you will find that the last wall
stave doesn't look like it fits properly, this is normal.
10
Secure every 2nd stave on the bottom of the sauna
with the provided nails to hold staves in place.
( If required)
* Once past the middle point of sauna, nails should no longer
be needed.
When installing the staves, tap tightly together
while leaving as much of a gap as possible
between stave and wall using the pencil line as a
guide as in picture.
*This will make the tightening of the bands easier.
Cedar Panoramic Barrel Sauna
Assembly Instructions
Table des matières
Autres manuels leisurecraft Produits de plomberie
leisurecraft
leisurecraft Outdoor Cabin Sauna Manuel utilisateur
leisurecraft
leisurecraft CTC88CW Manuel utilisateur
leisurecraft
leisurecraft Canadian Timber Mini Pod Manuel utilisateur
leisurecraft
leisurecraft Mini Pod Manuel utilisateur
leisurecraft
leisurecraft Canadian Timber Luna Manuel utilisateur
leisurecraft
leisurecraft Canadian Timber Tranquility Manuel utilisateur
leisurecraft
leisurecraft pure cube Neptune Manuel utilisateur
leisurecraft
leisurecraft pure cube Orion Outdoor Pure Cube Manuel utilisateur
leisurecraft
leisurecraft Luna Manuel utilisateur
leisurecraft
leisurecraft Cedar Barrel Sauna with Half Moon Windows Manuel utilisateur
