LEGRAND 0 648 75 Manuel utilisateur

2 AA batteries

2 x AA - 1,5 V

+ 5° C / + 45° C

PIR

2 - 8 m

5 à 1000 LUX

de 15 s à 15 min

IP 44

Pack contents

Wireless motion sensor

This product is a connected accessory which requires you to buy and install the «... with

Netatmo» connected starter pack and «... with Netatmo» connected power outlets, swit-

ches (with dimmer option) and/or connected lighting micromodules rst.

Specifications

This product can control up to 20

connected switches (with dimmer option),

micromodules, cable outlets and power

outlets «... with Netatmo»

Frequency bands: 2.4 - 2.4835 GHz

Power level: <10mW

Wireless motion sensor

0 648 75

LE11418AA







Do not x the motion sensor to the wall now.

The installation will be nalized on step 6.

Do not insert the batteries now

Start the wireless motion sensor configuration

Press the middle of the wireless master switch until its light briey turns green,

and then stop pressing. The indicator lights on the products which you have wired will

turn green.

Open the front cover









The motion sensor light will ash

green and then switch o.

Nota : if the motion sensor ashes green green red, then remove the batteries and

restart on Step 2

Insert the batteries in the wireless motion sensor

Make sure that the indicator lights on the wired products are green and not

ashing. If not, go back to step 2 and then comme back to step 4.

Pair the wireless motion sensor to a wired connected product

To pair a wireless motion sensor with a connected light switch, go to step 4.1.1

To pair a wireless motion sensor with a connected micromodule, go to step 4.2.1

To pair a wireless motion sensor with a connected power outlet, go to step 4.3.1

Phase A : Press the ON button on the wireless switch you wish to pair, while tapping it three

times onto the light switch you wish to control.

Phase B : The indicator lights on the two products will ash blue rapidly.

Phase C : The indicator lights on the two products will briey turn blue and stop ashing

Phase D : the light on the wired product will turn green again and the light on the wireless

motion sensor will switch o. The pairing was successful.

4.1.1 Pair a wireless motion sensor with a connected light switch

Press the ON and OFF buttons of the wireless motion

sensor to check if the light turns on and o correctly. If it

doesn’t, come back to step 4.1.1.

4.2.1 Pair a wireless motion sensor with a connected micromodule

Phase A : Press the ON button on the wireless switch you wish to pair, while tapping it

three times onto the micromodule you wish to control.

Phase B : The indicator lights on the two products will ash blue rapidly.

Phase C : The indicator lights on the two products will briey turn blue and stop ashing

Phase D : the light on the wired product will turn green again and the light on the wireless

motion sensor will switch o.

4.1.2 Check the correct pairing

A C

4.3.1 Pair a wireless motion sensor with a connected power outlet

Phase A : Press the ON button on the wireless switch you wish to pair, while tapping it three

times onto the power outlet you wish to control.

Phase B : The indicator lights on the two products will ash blue rapidly.

Phase C : The indicator lights on the two products will briey turn blue and stop ashing

Phase D : the light on the wired product will turn green again and the light on the wireless

motion sensor will switch o.

Press the ON and OFF buttons of the wireless motion

sensor to check if the light turns on and o correctly. If it

doesn’t, come back to step 4.1.1

4.1.2 Check the correct pairing

Multiple pairing

You can control several connected switches, micromodules and power outlets by repeating

the step 4 on each product you wish to control.

Complete the configuration

To complete your installation,

briefly press the middle of thewireless master switch.

All the indicator lights on the products switch off.

60 mm

Ø 3,5 mm maxi

Ø 6,5 mm

2,5

m60

Recommended places

Fix the motion sensor

For optimal use, the motion detector should be placed at a height of approximately 2.50

m from the ground.

To increase the time that the

associated product remains

ON (eg, light), turn the screw

(potentiometer) clockwise.

Set up the motion sensor

Time delay

Ambient light sensitivity

Movement sensitivity

8.1 Adjust the ambient light sensitivity

By default, the motion detector is set to a minimum delay (15 seconds), a maximum

light sensitivity (1000 lux) and a maximum sensor sensitivity (8 meters). If you want

to change these settings, fol-

low the steps below.

8.2 Adjust the ambient light sensitivity

8.3 Adjust the motion sensor sensitivity

In order for the sensor to detect only when it is dark, turn the screw (potentiometer)

counterclockwise.

To reduce the sensitivity of the motion sensor, turn the screw (potentiometer)

counterclockwise. The detection will then be at a shorter distance.

LEGRAND - Pro and Consumer Service - BP 30076

87002 LIMOGES CEDEX FRANCE • www.legrand.com

www.legrand.fr

Close the front cover

To add a connected product to your connected installation,

you should follow the instructions :

- in the Legrand Home + Control application (Settings/Add a new product section)

- or consult the user manual on legrand.fr





















Red led light : low

battery (*)

(*) 2 years batteries lifetime for 50

detections per day with a time delay of

3 minutes

SIMPLIFIED EU DECLARATION OF CONFORMITY

The undersigned,

Legrand

declares that the radio-electric equipment referred to in these instructions complies with directive 2014/53/EU.

The full text of the EU declaration of conformity

is available on the following website :

www.legrandoc.com

Batteries replacement

Autres manuels LEGRAND Capteur de sécurité

LEGRAND

LEGRAND CP Electronics MWS3A-AT-DD Manuel utilisateur

LEGRAND

LEGRAND 0 883 09 Manuel utilisateur

LEGRAND

LEGRAND 0 489 53 Manuel utilisateur

LEGRAND

LEGRAND Mosaic 0 489 22 Manuel utilisateur

LEGRAND

LEGRAND Tynetec ZXT805 Manuel utilisateur

LEGRAND

LEGRAND 695 93 Manuel utilisateur

LEGRAND

LEGRAND Wattstopper LMDC-100 Manuel utilisateur

LEGRAND

LEGRAND 0 884 09 Manuel utilisateur

LEGRAND

LEGRAND SANUS SAL-IWP2 Manuel utilisateur

LEGRAND

LEGRAND Wattstopper FSP-311B Manuel utilisateur

LEGRAND

LEGRAND Tynetec Aidcall Big Button Manuel utilisateur

LEGRAND

LEGRAND 0 489 36 Manuel utilisateur

LEGRAND

LEGRAND 431 17 Manuel utilisateur

LEGRAND

LEGRAND Mallia Senses with Netatmo 2 815 02DS/MB/MW Instructions d'utilisation d'origine

LEGRAND

LEGRAND CP Electronics EXD-HSC Manuel utilisateur

LEGRAND

LEGRAND Celiane 676 61 Manuel utilisateur

LEGRAND

LEGRAND 0 489 54 Mode d’emploi

LEGRAND

LEGRAND 0 488 06 Manuel utilisateur

LEGRAND

LEGRAND EMOS G1130 Manuel utilisateur

LEGRAND

LEGRAND Celiane 670 92 Manuel utilisateur

LEGRAND

LEGRAND CP Electronics EBDMR-DALI2 Manuel utilisateur

LEGRAND

LEGRAND HPM 630S01WE Manuel utilisateur

LEGRAND

LEGRAND Wattstopper LMPX-100-3 Manuel utilisateur

LEGRAND

LEGRAND Triscan 488TRI3W Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur