LEGRAND Tynetec Aidcall Manuel utilisateur

Doc No. FM0462 issue F Page 1

PLACE A DAMP CLOTH ON THE

BED MAT TO ACTIVATE

169MHz Telecare Devices

Enuresis Sensor & Plastic Bed Mat

__________________________________________________________________________________________________________

•Compatible with Reach at-home alarms, Advent xt warden call,

Altec Response and Touchsafe Pro Nursecall systems

•Interface unit complete with plastic bed mat

•Foil embossed plastic bed mat with 2.2 metre plug-in lead

•Interface unit with user replaceable 9V battery

•Low battery warning

•Bed mat dimensions: 540 x 420 mm

•Interface dimensions: 90 x 65 x 28 mm (HxWxD)

•Interface weight: 170 grams

•Product Code: ZXT431

•Replacement bed mat: Part No. W00369

Where should Enuresis Sensors be Located?

The bed mat should be placed between the bottom sheet and the mattress to detect instances of enuresis.

An alarm will be raised immediately moisture is detected thereby alleviating carers from making regular checks which can be

intrusive and unwelcome.

Installation

It is easier to register the Enuresis sensor before installation –see below.

1. Remove the bottom sheet from the bed.

2. Place the bed mat across the width of the bed at a point where

the hips of the person will be when lying down.

The mat must be placed metallic side up –text on the mat shows “THIS SIDE UP”.

3. If necessary secure the mat with cord through the 4 corner tie down points.

4. Ensure the wire exits safely without causing a hazard.

5. Place a bath towel over the top of the bed mat for best performance.

Be aware that nylon or polyester sheets can give false alarms.

6. Refit the bottom bed sheet.

7. Plug the lead into the interface unit and make sure it is placed

safely out of the way under the bed.

Testing and Registering the Enuresis Sensor

Remove the battery cover from the interface unit and

connect the battery lead –it only fits one way.

Place a damp cloth on the bed mat to activate.

The Enuresis sensor must be activated when registering it

onto the warden call, at-home alarm or Nursecall system.

See the following pages for how to put each of these

products into registration mode.

The range of all radio devices can be affected by the working environment - always take care during installation and

perform several test calls.

Tynetec and Aidcall are business units of Legrand Electric Ltd

Unit 10 Cowley Road, Blyth Riverside Business Park, Blyth

Northumberland, NE24 5TF. Tel: 01670 352 371

Email: sales@tynetec.co.uk Web: www.tynetec.co.uk

Doc No. FM0462 issue F Page 2

PP3 BATTERY

We declare this product complies with the relevant UK

legislation on condition that it is used in the manner

intended, and in accordance with the current installation

standards and/or the manufacturer's recommendations.

A copy of the full UKCA Declaration of Conformity is

available on request.

Mask Time & Battery Test

The Enuresis sensor transmitter has a 15 minute mask time to prevent the same alarm

call re-reporting several times. There is a facility for Engineers to override this mask

time and test the battery at the same time.

When the sensor is activated the alarm call will be transmitted once, no further

transmissions will occur for 15 minutes giving time for the cause to be cleared.

Engineer’s mask reset function; open the case, press and hold BUTTON 1 on the transmitter

for 2 seconds until the RED light flashes once. After a short delay the RED light will flash once more

to indicate the mask time is reset and the battery power is OK. If the RED light flashes several times the battery power is low.

Maintenance

The Enuresis sensor should be activated periodically to check the bed mat is functioning and verify operation.

Cleaning the Bed Mat

To prevent false alarms always un-plug the bed mat from the interface unit before cleaning.

The bed mat can be wiped clean with a damp cloth and soapy water or a mild disinfectant.

Do not fully submerge the bed mat lead or interface unit in water.

Replacement Bed Mats

Due to the nature of the product bed mats are non-returnable.

Replacement mats are available separately –order Tynetec Part No. W00369.

Battery Life

The battery is checked once a day, if the voltage falls and stays below a pre-set level for 7 consecutive days a low battery alert is

automatically transmitted. Once a low battery call is received the battery should be replaced within 7 days.

Detailed information on battery management for all Tynetec/Aidcall products is available - request Doc No. FM0630.

Battery Replacement

Slide the battery compartment cover off the rear

of the interface unit.

Disconnect the old battery and replace with an

identical type; 9V Duracell Plus MN1604.

Refit the battery compartment cover.

Perform a test call to check the new battery is

fitted and working correctly.

Declaration of Conformity

SLIDE THE COVER OFF

TO REVEAL THE BATTERY

9 Volt

Battery

PRESS AND HOLD

BUTTON 1 TO RESET

THE MASK TIME

THE RED LIGHT

WILL FLASH



We declare this product complies with the relevant

European legislation on condition that it is used in the

manner intended, and in accordance with the current

installation standards and/or the manufacturer's

recommendations. A copy of the full CE Declaration of

Conformity is available on request.

Doc No. FM0462 issue F Page 3

Registering an Enuresis Sensor onto a Reach at-home alarm unit

1. Put the Reach unit into radio device learn mode…

2. Activate the Enuresis sensor…

3. Exit radio device learn mode…

4. Check with the Control Centre that it is convenient to perform a test call, activate the Enuresis sensor and confirm they receive

an Enuresis alarm call.

Deleting an Enuresis Sensor from a Reach at-home alarm unit

Enter 1 6 7 0 using the keypad on the rear of the Reach unit –the front light will FLASH FAST GREEN and the unit will announce

“Program Mode - Ready”.

Enter # 0 4 1 and the Reach will announce “Delete Radio Device” followed by a “Beep”.

Enter the 8 digit Enuresis sensor IDto be deleted; after the “Beep” press #to exit.

Press the key to exit Program Mode; the unit will sound a “Double-Beep” and the front light will return to STEADY GREEN.



The 8 digit ID can be found on a label on the back of the Enuresis interface unit –it will always start with 32xxxxxx

The instructions given above for the standard Reach product also applies to the Reach Plus, Reach Plus GSM

and Reach Ultra models. Refer to the instruction booklets provided with these products for more information

on programming and testing radio devices.

“Trigger

Radio

Device”

Press and HOLD the GREEN button on the Reach unit.

When the front light FLASHES FAST GREEN release the

button and the Reach will announce “Trigger Radio Device”.

You now have 1 minute to activate the Enuresis sensor.



Press the GREEN button on the Reach unit.

The front light will return to STEADY GREEN and the Reach

is back in normal operating mode.

⚫

Place a damp cloth on the plastic bed mat, and the Reach will

announce “Enuresis”.

*Note: if the Enuresis sensor has been activated in the last 15

minutes you’ll have to reset the MASK TIME –see page 2.

Doc No. FM0462 issue F Page 4

Registering an Enuresis Sensor onto an Advent xt warden call system

1. Put the Advent xt system into radio device learn mode…

2. Activate the Enuresis sensor…

3. Exit the Advent xt system radio device learn mode…

4. Activate the Enuresis sensor and check an Enuresis alarm call is reported on the warden call system.

Deleting an Enuresis Sensor from an Advent xt warden call system

Press the LINE key and wait for the “Ready” prompt.

Enter 5 0 0 1 followed by the key.

Enter the flat number the Enuresis sensor is being deleted from followed by the key.

Activate the Enuresis sensor to be deleted.

Wait for the “Pendant Disabled –Enter Flat” prompt.

Press the #key and wait for the “Ready” prompt, then press the LINE key to clear the connection.

Refer to the Advent xt operator’s manual (Doc No. FM0420) provided with the warden call system for more

information on programming and testing radio devices.

Using the Manager’s DECT telephone;

Press the LINE key and wait for the “Ready” prompt.

Enter 5 0 0 0 followed by the key.

Enter the flat number the Enuresis sensor is being installed in

followed by the key.

You now have 1 minute to activate the Enuresis sensor.

“Ready”

Using the Manager’s DECT telephone;

Press the #key and wait for the “Ready” prompt.

Press the LINE key to clear the connection and the warden call system is

now back in normal operating mode.

“Ready”

Place a damp cloth on the plastic bed mat.

Wait for the “Enter Location Code” prompt then press 0(no

location) followed by the key.

Wait for the “Pendant Enabled –Enter Flat” prompt.

*Note: if the Enuresis sensor has been activated in the last 15

minutes you’ll have to reset the MASK TIME –see page 2.

Doc No. FM0462 issue F Page 5

Registering an Enuresis Sensor onto anAltec Response local carer alarm unit

1. Put the Altec Response unit into radio device learn mode…

2. Activate the Enuresis sensor…

3. Exit the Altec Response radio device learn mode…

4. Activate the Enuresis sensor and check an enuresis alarm call is displayed on the Altec Response unit.

Deleting an Enuresis Sensor from an Altec Response local carer alarm unit

Press ENTER to activate the wake-up display then ENTER again to display the main menu

Press ENTER to select Radio Devices 

Press the key to select Delete Device then press ENTER

The display will prompt you to “Trigger the Sensor”

Activate the Enuresis sensor to be deleted - the display will show the device type and its 8 digit ID number

If this is the device you activated press the key to select Delete then press ENTER

If it’s NOT the device you activated press the ENTER key to select Reject then try again

To exit the mode select Exit then press the ENTER key.

Refer to the Altec Response installation guide (Doc No. FM0548) provided with the portable alarm unit for

more information on programming and testing radio devices.

Place a damp cloth on the plastic bed mat.

The display will show Enuresis and the Enuresis sensor 8 digit ID number.

Check the ID is correct, press the key to select Accept then

press ENTER. Note: if another device has been picked-up press ENTER

to Reject and try again.

The display will show Flat , use the & keys to choose the

dwelling type.

Press the key to select No: 000000 then press the ENTER key.

Use the & keys to select each digit of the flat number and

the & keys to move between digits then press the ENTER key.

Press key several times to select Exit then press the ENTER key.

The display will prompt you to “Trigger the Sensor” again.

*Note: if the Enuresis sensor has been activated in the last 15 minutes you’ll

have to reset the MASK TIME –see page 2.

Press ENTER to activate the wake-up display then ENTER again to display

the main menu.

Press ENTER to select Radio Devices 

Press ENTER to select Learn Device 

The display will prompt you to “Trigger the Sensor”.

You now have 20 seconds to activate the Enuresis sensor.

tynetec

*Note: if the Enuresis sensor has been activated in the last 15 minutes

you’ll have to reset the MASK TIME –see page 2.

From the Learn Device menu select Exit then press ENTER.

From the Radio Devices menu select Exit then press ENTER.

The display will return to the wake-up screen and go blank after 10 seconds.

The Altec Response is now back in normal operating mode.

Doc No. FM0462 issue F Page 6

Registering an Enuresis Sensor onto aTouchsafe Pro Nursecall system

1. Put the Touchsafe Pro Master Panel into Telecare registration mode; touch the screen and Logon as an Engineer or a Manager

(password required), then from the main menu page touch the Telecare button to open the screen shown below…

2. Enter the Enuresis sensor ID…

3. Press the Close button to exit Telecare mode and the Nursecall panel is now back in normal operating mode.

4. Activate the Enuresis sensor and check the call is displayed on the Nursecall panel like this…

The screen banner is yellow for an Enuresis call (Touch the banner to display notes).

Press the Accept button on the banner to silence the alarm - this will also

notify all other panels the call is being dealt with.

The screen banner changes to purple when a call is accepted.

You must visit the appropriate Nursecall Call Point to cancel the call.

Deleting an Enuresis Sensor from a Touchsafe Pro Nursecall system

Select the Enuresis sensor ID to be deleted from the Delete Telecare Device pull-down list box (prefixed with a “T32”).

Details of the Enuresis sensor selected will be displayed in the Room, House Code and ID boxes below.

If the details shown are correct press the Delete button.

Press the Close button to exit.

Refer to the Touchsafe Pro Display Panel user guide (Doc No. FM5505) provided with the Nursecall system for

more information.

Tynetec and Aidcall operate a policy of continuous improvement and reserve the right to change product specifications without notice.

If any variation to the details contained in this document are suspected please contact Tynetec’s customer support dept on 01670 352371.

The 8 digit ID is printed on a label on the rear of the Enuresis interface unit.

Note: this ID will always start with 32xxxxxx.

Touch the Add Telecare Device box then use the on-screen keypad to enter the ID.

Hint: enter a zone in the Filter box to narrow the search for the room (see below).

Select the users Call Point ID from the Room pull-down list box then press Save.

Note: this is the room unit that will be used to cancel the call.

Use keypad to enter

8 digit ID here

Select the relevant

Call Point ID here

Save when done

Close to exit mode

On-screen keypad

CALLING

CANCEL

HC 345 ID 001

ZXT431 W64704

Ser: 09150491

ID: 32035593

EE0755 V1.04A

Press the LIGHT GREY

button to cancel the call

Autres manuels LEGRAND Accessoires

LEGRAND

LEGRAND Wattstopper PW-311 Manuel utilisateur

LEGRAND

LEGRAND 572 250 Manuel utilisateur

LEGRAND

LEGRAND Wattstopper CI-305 Manuel utilisateur

LEGRAND

LEGRAND WattStopper DW-100-347 Manuel utilisateur

LEGRAND

LEGRAND WattStopper UT-300 Series Manuel utilisateur

LEGRAND

LEGRAND Pass & Seymour WSP101 Manuel utilisateur

LEGRAND

LEGRAND Pass & Seymour PSHB120277L Series Manuel utilisateur

LEGRAND

LEGRAND Wattstopper LMDL-600 Manuel utilisateur

LEGRAND

LEGRAND 882 08 Manuel utilisateur

LEGRAND

LEGRAND Celiane 673 13 Manuel utilisateur

LEGRAND

LEGRAND Wattstopper DW-311-I Manuel utilisateur

LEGRAND

LEGRAND EW Series Mode d’emploi

LEGRAND

LEGRAND 0 770 53 Manuel utilisateur

LEGRAND

LEGRAND Watt Stopper CI-355 Manuel utilisateur

LEGRAND

LEGRAND Plexo 695 56 Manuel utilisateur

LEGRAND

LEGRAND Wattstopper UW-100 Manuel utilisateur

LEGRAND

LEGRAND WattstopperFS-205 Manuel utilisateur

LEGRAND

LEGRAND Wattstopper FSP-212 Manuel utilisateur

LEGRAND

LEGRAND 6 946 90 Manuel utilisateur

LEGRAND

LEGRAND HD15 Manuel utilisateur

LEGRAND

LEGRAND Valena Life LE-753186 Manuel utilisateur

LEGRAND

LEGRAND Wattstopper FSP-211 Manuel utilisateur

LEGRAND

LEGRAND DX2 Series Manuel utilisateur

LEGRAND

LEGRAND 0 506 90 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur