Leedarson 6A-PL-VAB-C0 Manuel utilisateur
EU Smart Plug （Z-Wave）
User Guide
(6A-PL-VAB-C0)
Smart plug is a Z-Wave Switch plug in module specifically used to enable Z-Wave
command and control (on/off) of any plug-in tool. It can report wattage consumption or
kWh energy usage.
Smart Plug can be included and operated in any Z-Wave network with other Z-Wave
certified devices from other manufacturers and/or other applications. All non-battery
operated nodes within the network will act as repeaters regardless of vendor to increase
reliability of the network.
Smart Plug is also a security Z-Wave device and supports the Over The Air (OTA) feature for
the product’s firmware upgrade.
If you want your Smart Plug to be a security device that use secure/encrypted message to
communicate in a Z-Wave network, then a security enabled Z-Wave controller is needed.
Features:
1) Supporting 1xAC output;
2) AC output switch on/off by manual or Z-Wave command;
3) LED indicates the Z-WAVE network range;
4) LED indicates the load power;
5) Supporting power meter;
6) Supporting repeater role;
7) Supporting firmware OTA;
1 Familiarize yourself with your Smart Plug
Smart Plug Layout
2 Technical specifications
2.1 Hardware specifications
Rated voltage:
230V~，50Hz
Rated load current:
10A
Power consumption:
≤1.5W
Rated Power output
(plug for resistive load):
2300W
Operational temperature:
0℃~35℃（testing 25℃）
Radio protocol:
Z-Wave
Radio frequency:
Maximum RF output power：
868.0-868.6MHz,869.7-870MHz
1.68mW
Additional SPEC:
Rated impulse withstand voltage: 2.5KV
Duty-type：S1, continuous duty
Number of operating cycles: 10000
CIRCUIT DISCONNECTION: Micro-disconnection
Glow-wire temperature: 650 °C
Non-replaceable built-in protection: thermal fuse,10A, 84°C,
Do not connect after each other
Frequency Range：868.0-868.6 MHz, 869.7-870MHz.
2.2 Software specification
1, Command List
Included Non-Secure Network
Included Secure Network
Node
Info
COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_SWITCH_BINARY
COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_SECURITY
Frame
COMMAND_CLASS_SECURITY
COMMAND_CLASS_MANUFACTURER_
SPECIFIC
COMMAND_CLASS_VERSION
COMMAND_CLASS_BASIC
COMMAND_CLASS_SWITCH_BINARY
COMMAND_CLASS_SWITCH_ALL
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GR
P_INFO
COMMAND_CLASS_MANUFACTURER_
SPECIFIC
COMMAND_CLASS_DEVICE_RESET_LO
CALLY
COMMAND_CLASS_METER_V3
COMMAND_CLASS_SCENE_ACTIVATIO
N
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_FIRMWARE_UPDA
TE_MD_V4
COMMAND_CLASS_SCENE_ACTUATO
COMMAND_CLASS_MANUFACTURER_
SPECIFIC
COMMAND_CLASS_VERSION
COMMAND_CLASS_TRANSPORT_SERV
ICE_V2
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_POWERLEVEL
R_CONF
Security
Comma
nd
Support
ed
Report
Frame
COMMAND_CLASS_BASIC,
COMMAND_CLASS_SWITCH_BINARY,
COMMAND_CLASS_SWITCH_ALL,
COMMAND_CLASS_ASSOCIATION,
COMMAND_CLASS_ASSOCIATION_GR
P_INFO,
COMMAND_CLASS_DEVICE_RESET_LO
CALLY,
COMMAND_CLASS_CONFIGURATION_
V3,
COMMAND_CLASS_METER_V3,
COMMAND_CLASS_SCENE_ACTUATO
R_CONF,
COMMAND_CLASS_SCENE_ACTIVATIO
N,
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_FIRMWARE_UPDA
TE_MD_V4
2, SDK 6.71.01
3, Library
Device Type
Generic Device
class
Specific Device
Class
Role Type
On/Off
Power Switch
GENERIC_TYPE
_SWITCH_BIN
ARY
SPECIFIC_TYPE_P
OWER_SWITCH_BI
NARY
ROLE_TYPE_SLAV
E_ALWAYS_ON
3 LED indicator mode
Smart Plug’s LED indicator supports two work modes, including Power indication mode
and
night lamp mode.
Power indication mode: Power indication mode will allow the LED to follow the state of the
Smart Plug, when the Plug is on, LED will be on in the color blue, and
while the Plug is off, LED will off.
Night lamp mode: Night lamp mode will allow LED turn on hold 5 seconds and then turn off
When the Smart plug state changes you have configured.
4 Functions of each trigger
Function of ZWAVE Button:
Smart Plug is not in the Z-Wave network:
Trigger
Description
Power on
1. LED has been slow flash, Smart Plug sends security node
info frame.
2. Add for inclusion(security)
1. Set the Z-Wave network main controller into learning
mode.
2. Short press the Z-button twice
3. The LED keep blink to the end of add inclusion, If the
add for inclusion is successful, LED will turn on within
2 seconds and Then will be in power indication mode,
Otherwise, The LED will keep slow flash.
Short press one
(within 1 second)
1. LED has been slow flash, Smart Plug sends security node
info frame.
2.Add for inclusion(security);
1. Set the Z-Wave network main controller into learning
mode.
2. Short press the Z-button twice,
1. The LED keep blink to the end of add inclusion, If the
add for inclusion is successful, LED will turn on within
2 seconds and Then will be in power indication mode,
Otherwise, The LED will keep slow flash.
Short press twice
(within 1 second)
1. LED has been slow flash, Smart Plug sends non-security
node info frame.
2.Add for inclusion(non-security);
1. Set the Z-Wave network main controller into learning
mode.
2. Short press the Z-button twice
2. The LED keep blink to the end of add inclusion, If the
add for inclusion is successful, LED will turn on within
2 seconds and Then will be in power indication mode,
Otherwise, The LED will keep slow flash.
Short press triple
1. LED has been slow flash, Smart Plug sends security node
info frame.
2.Add for inclusion(security);
3. Set the Z-Wave network main controller into learning
mode.
4. Short press the Z-button triple
5. The LED keep blink to the end of add inclusion, If the
add for inclusion is successful, LED will turn on within
2 seconds and Then will be in power indication mode,
Otherwise, The LED will keep slow flash.
Smart Plug is in the Z-Wave network:
Trigger
Description
Short press once
1. Changing the status of Smart Plug’s load.
2. LED will be in power indication mode.
Short press twice
1. Smart Plug will send node info frame.
2. Remove for exclusion:
1. Set the Z-Wave network main controller into
removing mode.
2. Short press Z-button twice.
3. The LED keep blink to the end of remove exclusion, If
the remove for exclusion is successful, The LED will
keep slow flash, Otherwise, LED will be in power
indication mode.
Short press triple
1. Smart Plug will send node info frame.
2. Remove for exclusion:
1. Set the Z-Wave network main controller into
removing mode.
2. Short press Z-button triple.
3. The LED keep blink to the end of remove exclusion, If
the remove for exclusion is successful, The LED will
keep slow flash, Otherwise, LED will be in power
indication mode.
Press more than
5seconds
Reset Smart Plug to factory Default: LED in 5 seconds to
accelerate flash, The reset successful will
send“Device_Reset_Locally” to the main controller and
exclude from the Z-Wave network, this procedure will reset
Smart Plug to factory default.
5 Note for special command
5.1 Association Command
1, The Smart Plug supports only one association group.
Grouping
Identifier
Max
Nodes
Send Commands
Group 1
0x05
1. When the state of Smart Plug (turn on or off the load)
is changed:
1.Set Configuration parameter 0x03 to 0:Do not send
Basic Report
Table des matières
