LEDISONS LDS77-5CAF-ZI Manuel utilisateur

LDS77-5CAF-ZI

Function introduction

Important: Read All Instructions Prior to Installation

Product Data

Operation

•This device contains button lithium batteries that shall be stored and disposed properly.

• DO NOT expose the device to moisture.

Safety & Warnings

Zigbee LED Strip Remote

Protocol

Operation Voltage

Transmission Frequency

Transmission Range (free field)

Dimming Range

Dimension

Protection Grade

ZigBee 3.0

6V(2*CR2032 battery)

2.4GHz

30m

0.1%-100%

137x45x13mm

IP20

Front side

Bottom side

1.This ZigBee remote is a wireless transmitter that communicates with a variety of ZigBee compatible

systems. This transmitter sends wireless radio signals that are used to remotely control a compatible

system.

2.This ZigBee remote supports 4 groups for binding max. 30 lighting devices and enables to control

DIM, CCT, RGB, RGBW and RGB+CCT zigbee lighting devices.

ZigBee Clusters Supported by This Remote Are As Follows:

Input clusters:

•Basic •Power Configuration •Identify •Diagnostics

Output clusters:

•Identify •Group •Scene •On/off •Level control •Ota •Color control

Click to get the maximum

RGB saturation, press and

hold down to increase/

decrease color saturation

Press and hold down to

decrease light intensity

S1-S7, press and hold down to

save colors, click to recall the

saved colors

RGB Color wheel

LED indicator

Press and hold down to increase

light intensity

Group numbers: Click to choose

the group, with indicator under each

group button, when the groups are

chosen, indicators turn on

Click to recall 6 preset

scenes one by one

6V(2*CR2032 battery)

Note:Before the first use, please remove the protective film on the battery.

ON/OFF button

Click to turn on/off warm white,

press and hold down to adjust

warm white between 0%-100% Click to turn on/off cool white,

press and hold down to adjust

cool white between 0%-100%

Click to recall 5 preset Kelvin one by one

•ZigBee RGB+CCT+DIM remote based on ZigBee 3.0

•High sensitive & high stable touch color wheel, fast & precise color control

•Battery powered remote with low power consumption

•Enables to pair ZigBee lighting devices through touchlink commissioning

•Supports find and bind mode to pair with ZigBee lighting devices

•Supports 4 groups for binding max. 30 lighting devices

•With 6 preset scenes, 5 preset Kelvin, enables to save and recall 7 scenes

•Enables to adjust RGB color saturation

•2.4 GHz global operation

•Transmission range up to 30m

•Compatible with universal ZigBee Gateway products

•Enables to bind and control universal DIM, CCT, RGB, RGBW and RGB+CCT zigbee lighting devices

Anleitung

Manuel

Handleiding

3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)

LED indicator

5. Removed from a Zigbee Network through Coordinator or Hub Interface

6. Factory Reset Manually

Note: 1) After pairing successfully, the remote information will appear on the controller or hub interface.

2) No remote information will appear on the hub interface if pairing to Philips Hue Bridge.

4. TouchLink to a Zigbee Lighting Device

Note: 1) Directly TouchLink (both not added to a ZigBee network), each remote can link with 30 devices.

2) TouchLink after both added to a ZigBee network, each remote can link with max. 30 devices.

3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.

4) After TouchLink, the remote can control the linked lighting devices.

7. Remove a Touchlink Paired ZigBee Lighting Device

8. Factory Reset a Lighting Device (Touch Reset)

Step 1: Remove the remote from

previous zigbee network if it has already

been added to it, otherwise pairing will

fail. Please refer to the part "Factory

Reset Manually".

Step 2: From your zigbee controller or

hub interface, choose to add device or

accessory and enter Pairing mode as

instructed by the controller.

Step 3: Press and hold down until LED

indicator turns on.

Step 4: Immediately short press to

search nearby network, indicator

flashes every 1 second, 20 seconds

timeout if there is no network. Indicator

will then blink 5 times quickly for

successful pairing.

From your ZigBee controller or hub

interface, choose to delete or reset

the remote as instructed, indicator

flashes 3 times quickly to indicate

successful removing.

ZigBee Lighting Device

< 10cm

Step 1: Set the Touchlink paired zigbee

device to start TouchLink

commissioning, please refer to its

manual to learn how.

LED indicator

Step 2: Bring the remote within 10cm of

the lighting device.

Step 3: Short press the group button

that the device was linked to.

ZigBee Lighting Device

< 10cm

Step 1: Set the zigbee lighting device to

start TouchLink commissioning, please

refer to its manual to learn how.

LED indicator

Step 2: Bring the remote within 10cm of

the lighting device.

LED indicator

Step 2: Immediately short press 5 times

continuously, indicator flashes 3 times

quickly to indicate successful reset.

Step 1: Press and hold down until LED

indicator turns on.

Note: All configuration parameters

will be reset after the remote is reset

or removed from the network.

Step 3: Press and hold down any group

button to start TouchLink commissioning

of the remote. LED indicator flashes fast

for 3S, then flash 6 times slowly to

indicate successful pairing to the device

and the light connected to the device

will blink twice.

Step 4: Press and hold down until LED

indicator turns on.

Step 5: Immediately short press twice to

start TouchLink removing of the remote.

LED indicator flashes fast for 3S, then

flash 6 times slowly to indicate

successful removing.

ZigBee Lighting Device

< 10cm

Step 1: Set the Touchlink paired zigbee

device to start TouchLink

commissioning, please refer to its

manual to learn how.

LED indicator

Step 2: Bring the remote within 10cm of

the lighting device.

Step 3: Press and hold down until LED

indicator turns on.

Step 4: Immediately short press 5 times

to start Touch Reset of the remote. LED

indicator flashes fast for 3S, then flash 3

times slowly to indicate successful

reset.

Note: the device shall be added to a network,

the remote added to the same one or not

added to any network.

9. Find and Bind a Zigbee Lighting Device

10. Find and Unbind a Zigbee Lighting Device

11. Clear All Find and Bind Mode Paired Lighting Devices of a Group

12. Setup a Network & Add Devices to the Network (No Coordinator or Hub Required)

Step 6: Add more remotes to the network as you would like.

Step 7: Factory reset the lighting devices that you would like then add them to the network, refer to their manuals.

Step 8: Touchlink to pair the added remotes and lighting devices, refer to their manuals. Each remote can link

with max. 30 lighting devices. Each lighting device can be linked by max. 30 remotes.

15. Battery Power Monitor Function

The remote will report battery power value to the coordinator under following situations:

• When powered on.

• When operating the switch to send data packets (over 4 hours since last operation).

• When added to the network by a coordinator.

14. How to Check Whether the Remote Belongs to a Network or not

Short press any other buttons except group buttons, indicator blinking means the remote has already been

added to a network, no blinking of indicator means the remote does not belong to any network.

ZigBee Lighting Device

Step 1: Start find and bind mode on the

Zigbee lighting device (initiator node)

and enable it to find and bind target,

refer to its manual.

LED indicator

Step 2: Short press a group button that

you would like to bind the device to.

Step 4:Short press to enable the remote

(target node) to find and bind initiator.

LED indicator flashes 4 times for

successful binding or twice if binding fails.

Note: Each remote can bind max. 30

lighting devices.

ZigBee Lighting Device

Step 1: Start find and bind mode on the

ZigBee lighting device (initiator node)

and enable it to find and unbind target,

refer to its manual.

Step 2: Short press the group button

that the device already bound to.

Step 4:Short press twice to enable the

remote (target node) to find and unbind

initiator. LED indicator flashes 4 times

for successful unbinding or twice if

unbinding fails.

Step 1: Short press to choose the group

that you would like to unbind all devices.

Step 3:Short press 5 times continuously

to clear all bound lighting devices with this

group. LED indicator flashes 4 times for

successful unbinding.

ZigBee Lighting Device

< 10cm

Step 1: Factory reset the remote and

the lighting device, refer to their

manuals.

LED indicator

Step 2: TouchLink the remote and

device to setup a network, refer to their

manuals.

Step 4: Short press to enable the network

to discover and add devices, LED

indicator will flash twice. 180 seconds

timeout, repeat the operation.

Step 5:Set another remote into network

pairing mode and pair it to the network,

refer to its manual.

Note: Make sure the device and remote already added to the same zigbee network.

13. OTA

The remote supports firmware updating through OTA, and will acquire new firmware from zigbee controller or

hub every 10 minutes automatically.

Step 3: Press and hold down until LED

indicator turns on.

LED indicator

Step 3: Press and hold down until LED

indicator turns on.

LED indicator

Step 2: Press and hold down until LED

indicator turns on.

Step 3: Press and hold down

until LED indicator turns on.

Autres manuels LEDISONS Télécommande

LEDISONS

LEDISONS LDM43-1236-A Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation