Ledgerware 13 GPU Mining Rig Case Manuel utilisateur

LEDGERWARE

13 GPU Mining Rig Case

Assembly Instructions

LEDGERWARE

Assembly Instructions

13 GPU Mining Rig Case

Components Included in Kit

•13 x Riser Kits (In the case + riser configurations only)

o1 x Riser PCB

o1 x USB 3.0 Cable

o1 x SATA or Molex Power Cable

o1 x PCI to USB Adapter

•1 x Accessories Kit

o6-32 Screws

o6-32 Standoffs

oPower Supply Screws

oDual PSU Adapter

•1 x GPU Safety Bar

•1 x GPU Support Bar

•1 x Riser Mount Bar

•1 x Chassis Body

•1 x Chassis Top

•1 x Front Panel PCB

•1 x Hard Drive Mounting Bracket

•12 x Case Fans

Components NOT Included

These components are referenced in the instructions but are not included with

the mining kit.

•ATX Power Supply

•2.5” Hard Drive (optional if booting from an external source)

•ATX Mother Board

•ATX Mother Board Pass-Through Plate

•Graphics Cards

LEDGERWARE

Assembly Instructions

13 GPU Mining Rig Case

General Case Layout

SAFETY

DO NOT ASSEMBLY THE CASE OR ANY CASE COMPONENTS

THAT ARE POWERED. GROUND YOURSELF BEFORE

HANDLING ELETRONIC COMPONENTS TO MINIMIZE THE

POTETIAL FOR STATIC DISCHARGE DURING ASSEMBLY.

LEDGERWARE

Assembly Instructions

13 GPU Mining Rig Case

Step 1: Unboxing

•Open the box and remove the case from the shipping foam and

plastic cover.

•Remove the accessories kit (bag or box) from the box.

•Remove the risers and riser components from the box (if the case

+ riser package was purchased).

Step 2: Open the Case

Remove the two screws from the back of the case that keep chassis

top from sliding backwards with a Phillips head screwdriver.

Slide the chassis top backwards and set the chassis top aside.

Remove the GPU Safety, GPU Support & Riser Support Bars from the

case.

LEDGERWARE

Assembly Instructions

13 GPU Mining Rig Case

Step 3: Add ATX Mother Board

Add the ATX mother board pass-through plate (usually included with

your ATX mother board).

Reference the hole-pattern on your ATX mother board and add the

brass 6-32 standoffs that are included in the accessories kit.

Place your ATX mother board on the standoffs that were just

added to the case.

Attach the ATX mother board to the standoffs using the 6-32

screws included in the accessories kit.

Attach the Power/Reset Buttons & Power/Status LEDs to the ATX

main board. Consult your ATX mother board instructions for the

attachment locations.

LEDGERWARE

Assembly Instructions

13 GPU Mining Rig Case

Step 4: Add ATX Power Supply

Attach ATX power supply to the back panel of the case using the four

screw holes highlighted with green circles.

Note: If you are using two power supplies, repeat this step in the second

power supply location. After both power supplies are installed attach

the Dual PSU Adapter (from the accessories box).

LEDGERWARE

Assembly Instructions

13 GPU Mining Rig Case

Attach the Dual PSU Adapter to each PSU. Make sure that any

additional Mother Board Power comes from PSU1 so that it shares the

same ground connection as the ATX Mother Board Power Connector.

Step 5: Attach Fans to Power Supply

Daisy-chain the six molex fans connectors together and then attach one

of the molex fan cables to the power supply.

Repeat this step for the six fans in the back of the case.

LEDGERWARE

Assembly Instructions

13 GPU Mining Rig Case

Step 6: Add Hard Drive

Remove the hard drive mounting bracket by removing the 4 screws

holding it in place (with a Phillips head screwdriver).

Attach your hard drive to the mounting bracket by screwing the base of

the hard drive to the bracket. Your bracket may look different than the

one in the example below.

LEDGERWARE

Assembly Instructions

13 GPU Mining Rig Case

Step 7: Attach the Risers to the Riser Support Bar

Start by attaching the PCI to USB adapters and USB Cords into the

motherboard. This will save the hassle of attaching these components

once space becomes an issue.

Punch a hole through the foam covering the bottom of mounting holes

on the risers. This will allow you to use the mounting screws on the

Riser Support Bar.

Attach the risers using the two standoffs that are on the Riser Support

Bar using the screws provided in the accessories kit.

Once all the risers are attached to the Riser Support Bar, attached the

Riser Support Bar to the inside of the chassis.

LEDGERWARE

Assembly Instructions

13 GPU Mining Rig Case

Attach the USB Cords and power from the PSU to the risers.

Autres manuels Ledgerware Accessoires informatiques

Ledgerware

Ledgerware 6U Server Rack Mount Case Manuel utilisateur

Manuels Accessoires informatiques populaires d'autres marques

Motorola

Motorola ATRIX Manuel utilisateur

HP USB Media Docking Station Manuel utilisateur

Cherry

Cherry B.UNLIMITED 3.0 Manuel utilisateur

Logitech

Logitech IO2 Manuel utilisateur

ARM

ARM DSTREAM-ST Manuel utilisateur

Bartec

Bartec TC 7 Series Manuel utilisateur

Philips

Philips SPC3540 Manuel utilisateur

Logitech

Logitech mk220 Manuel utilisateur

SilverStone

SilverStone LC02 Manuel utilisateur

Flexispot

Flexispot ML2B Manuel utilisateur

Hamlet

Hamlet UNIVERSAL COVER 101 KBT2 Manuel utilisateur

Adam Equipment

Adam Equipment RS-485 Manuel utilisateur

Vivo

Vivo MOUNT-KB05-4DW Manuel utilisateur

Kvaser

Kvaser Memorator Professional Manuel utilisateur

DRC

DRC D-Imaging Manuel utilisateur

Sven

Sven Base 305 сombo Manuel utilisateur

Hama

Hama 108310 Manuel utilisateur

SpeechWare

SpeechWare FlexyMike FMK03 Manuel utilisateur