LCI Thin Shade Instructions d'installation
1
lci1.com 574-537-8900 Rev: 02.07.20
Thin Shade
Installation and Owner’s Manual
(For Aftermarket Applications)
CCD-0001507
Thin ShadeThin Shade
Part #Part # DescriptionDescription
786037 Window Shade
Table of Contents
Introduction ............................................ 1
Safety Information ..................................... 2
Resources Required ................................... 2
Parts List ................................................ 2
Installation-Snap Frame ............................... 2
Installation - Screw-in Frame .......................... 3
Thin Shade
For LCI RV Entry Door
Installation and
Owner’s Manual
(For Aftermarket Applications)
Introduction
This document provides the procedure to install the LCI
Thin Shade into a LCI RV entry door with the 711862 Outer
Frame/786036 Inner Frame snap-together frame, or the
387500 Outer Frame/387501 Inner Frame screw-together
frame.
Additional information about this product can be obtained
from support.lci1.com or by downloading the free myLCI
app. The app is available on iTunes®for iPhone®and iPad®
and also on Google Play™for Android™users.
iTunes ®, iPhone®, and iPad®are registered trademarks of
Apple Inc.
Google Play™and Android™are trademarks of Google Inc.
2
lci1.com 574-537-8900 Rev: 02.07.20
Thin Shade
Installation and Owner’s Manual
(For Aftermarket Applications)
CCD-0001507
Letter Part # Description Qty
A786037 Thin Shade 11 7/8” x 21 1/2” 1
Safety Information
Resources Required
• Cordless or electric drill or screw gun
• Phillips screwdriver
• Appropriate drive bits
• Tape measure
Parts List
A
Installation-Snap Frame
1. Unlatch the small levers at the top of the window frame
in a left-to-right direction (Fig.1).
2. Unlatch the levers at the bottom of the frame in a right-to
left direction (Fig.1).
3. If equipped, remove the existing shade from the frame
and discard.
4. Holding the top shade sill at an approximate 45 degree
angle, insert one end into the corner between the inner
frame and glass (Fig.2A).
5. Repeat this action on the opposite end of the top sill.
6. Press both ends up and latch in place moving levers in a
right-to-left direction.
Fig.1
levers
levers
MOVING PARTS CAN PINCH, CRUSH OR CUT. KEEP
CLEAR AND USE CAUTION.
3
lci1.com 574-537-8900 Rev: 02.07.20
Thin Shade
Installation and Owner’s Manual
(For Aftermarket Applications)
CCD-0001507
7. Holding the bottom shade sill at an approximate 45
degree angle, insert one end into the corner between the
inner and outer frame (Fig.2B).
8. Repeat this action on the opposite end of the bottom sill.
9. Press both ends down and latch in place, moving levers
in a left-to-right direction.
Fig.3
A
B
Fig.2
Installation - Screw-in Frame
NOTE: Door must be equipped with #387501 inner frame.
1. Working from the bottom of the shade, locate the bottom
sill xture (Fig.3A).
2. Remove end caps from center of xture.
3. Locate the knots tied at the end of each cord (Fig.3B).
bottom sill
end cap end cap
½”
A
B
FAILURE TO FOLLOW THE RECOMMENDED
PROCEDURE OF REMOVAL COULD RESULT IN
PERSONAL INJURY FROM BROKEN GLASS OR
DAMAGE TO EQUIPMENT. IT IS IMPORTANT TO
REMOVE THE PHILLIPS HEAD SCREWS IN THE ORDER
STATED.
4. Measure ½” up from the existing knot and mark the
cord.
5. Repeat this action on the opposite cord.
6. Create a new knot on both cords, at the marks made in
step 4.
7. Pull bottom sill of shade down to the newly created
knots.
8. Replace end caps.
4
lci1.com 574-537-8900 Rev: 02.07.20
Thin Shade
Installation and Owner’s Manual
(For Aftermarket Applications)
CCD-0001507
Fig.4
A A
A A
A A
A
A
B
B
B
B
B B
B B
9. Remove the top 8 Phillips head screws (Fig.4A) from the
interior window frame. Do not discard screws.
10. Gently pull back the top of the frame.
11. If currently equipped, remove the existing window
shade from inside of the interior window frame.
12. Holding the top shade sill at an approximate 45 degree
angle, insert one end into the corner between the inner
frame and glass (Fig.4).
13. Repeat this action on the opposite end of the top sill.
14. Press both ends up until the part is securely in place.
15. Top sill must be seated above tabs (Fig.5A)
16. Press top of frame back into position and replace
Phillips head screws removed in step 9.
17. Remove the bottom 8 Phillips head screws (Fig.4B) from
the interior window frame. Do not discard screws.
Fig.5
A
B tabs tabs
top sill
bottom sill
18. Holding the bottom shade sill at an approximate 45
degree angle, insert one end into the corner between the
inner frame and glass (Fig.4).
19. Repeat this action on the opposite end of the bottom
sill.
20. Press both ends down until the part is securely in
place.
21. Bottom sill must be seated below tabs (Fig.5B)
22. Press bottom of frame back into position and replace
Phillips head screws removed in step 16.
Manual information may be distributed as a complete
document only, unless Lippert Components provides
explicit consent to distribute individual parts.
All manual information is subject to change without
notice. Revised editions will be available for free
download at lci1.com. Manual information is considered
factual until made obsolete by a revised version.
Please recycle all obsolete materials and contact
Lippert Components with concerns or questions.
Ce manuel convient aux modèles suivants
1
Autres manuels LCI Accessoires automobiles
