Launch J2534 Manuel utilisateur

LAUNCH Smartbox 3.0-J2534 Operation Manual

1/ 15

Smartbox 3.0-J2534 Operation Manual

LAUNCH Smartbox 3.0-J2534 Operation Manual

2/ 15

Content

1Connection of Smartbox3.0 ......................................................................................................3

2Installation of Software Package and Driver.............................................................................3

2.1 Installation Steps of Software Package .........................................................................3

2.1.1 Installation Steps of Software Package .............................................................3

2.1.2 J2534 Registry Information View (Reserved)...................................................6

3Firmware Upgrade and Log Generation....................................................................................7

3.1 Firmware Upgrade Function .........................................................................................8

3.2 Log View Function........................................................................................................8

3.3 Communication Method Configuration (Reserved)....................................................10

3.3.1 Communication Method Configured as USB..................................................10

3.3.2 Communication Method Configured as USB to Ethernet Adapter .................12

LAUNCH Smartbox 3.0-J2534 Operation Manual

3/ 15

1Connection of Smartbox3.0

Smartbox3.0 comes with a USB cable.

One end of Smartbox3.0 is connected to the USB cable: one port of the USB cable is connected to

Smartbox3.0; the other port is connected to a USB port of a PC; the other end of Smartbox3.0 is

connected to the OBD interface bus, and the other port of the bus is connected to the OBD

connector.

2Installation of Software Package and

Driver

2.1 Installation Steps of Software Package

2.1.1 Installation Steps of Software Package

Attention：Please ensure that the PC user has administrator

rights and Smartbox3.0 has been connected to a PC before

installation.

Step 1:Open "SmartBox_3.0_Setup.exe", and select the installation path according

to prompts

Step 2: Click 'Change' to select the installation path, and then click 'Next'

LAUNCH Smartbox 3.0-J2534 Operation Manual

4/ 15

Step 3: After confirming the installation path, click 'Next'

Step 4: Click 'Next' to start to install the driver. It is recommended to have the

device connected before installing the driver. The software shall install by itself.

LAUNCH Smartbox 3.0-J2534 Operation Manual

5/ 15

Step 5: Click 'Done'. Drivers installed!

Step 6: Click 'Done' again. Software installed!

LAUNCH Smartbox 3.0-J2534 Operation Manual

6/ 15

2.1.2 J2534 Registry Information View (Reserved)

After installing the software, LAUNCH's corresponding registration information about J2534Dll

can be seen in the registry. Open "Run" window (shortcut "Windows+R"); enter the command

"regedit", as shown below:

Enter the registry, and find LAUNCH's J2534 DLL registration information according to the

following path: HKEY_LOCAL_MACHINE\SOFTWARE\PassThruSupport.04.04

LAUNCH Smartbox 3.0-J2534 Operation Manual

7/ 15

Note: It may be because of the 64-bit operating system, if you cannot view the registration

information. You can find it according to the following path:

HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\PassThruSupport.04.04

The Screenshot is shown below:

3Firmware Upgrade and Log Generation

Run "SmartBox Tool 3.0" on the Windows desktop after installing

"SmartBox_3.0_Setup".

LAUNCH Smartbox 3.0-J2534 Operation Manual

8/ 15

3.1 Firmware Upgrade Function

SmartBox 3.0 can be upgraded through SmartBox Tool 3.0. Please select "M7

Upgrade" for the upgrading of lower programs and "A7 Upgrade" for the

upgrading of the system. Click "Browse" to select the path for storing upgrading

files and click "Upgrade".

Note: Restart the software and SmartBox 3.0 upon completion of the

upgrade. You can check the version to confirm whether the upgrade is

successful.

3.2 Log View Function

When necessary, you can enable "Write Log File" or "Window Print Information"

function to record the test status of SmartBox 3.0 and the process. To avoid software

errors due to overlarge log files, do not enable the function if it is not necessary. The

log files are saved under the root directory of disk C by default.

Steps: The corresponding J2534Log information can be generated by ticking the

“Write Log File” option after clicking “View Log” in the upper left corner of the

software interface, as shown below:

LAUNCH Smartbox 3.0-J2534 Operation Manual

9/ 15

Note: Please restart the diagnostic software!

Note: If the log printing function is enabled, the log files may be very large as the information

are written accumulatedly. Please enable this function when necessary, such as development and

debugging. In other cases, please do not activate this function option at will.

The default storage path of the log file "J2534Log" generated is: C:\Program Files\SmartBox

3.0\SmartBox 3.0\Log\ J2534_LOG.txt, as shown below:

Also note: In some computer systems, users have no write permission to this file folder, resulting

in unsuccessful log file generation. It is necessary to modify the permissions of this folder

(requiring administrator privileges), as shown below:

LAUNCH Smartbox 3.0-J2534 Operation Manual

10 / 15

Right-click the "Log" folder, select the "Attribute" option and find the "Security" attribute, select

current user, click "Edit", select the corresponding user name again, and tick all the "Allow"

options in the permission column (requiring administrator rights), and click "OK" to go back.

3.3 Communication Method Configuration (Reserved)

SmartboxTool can be used only when the USB mode configuration function is available.

3.3.1 Communication Method Configured as USB

Table des matières

Autres manuels Launch Équipement de diagnostic

Launch

Launch Creader Professional 909X Manuel utilisateur

Launch

Launch X-431Diagun Manuel utilisateur

Launch

Launch X-431 PADII Manuel utilisateur

Launch

Launch M-Diag Lite Manuel utilisateur

Launch

Launch X-431-IMMO Pad Manuel utilisateur

Launch

Launch X-431 Throttle III Manuel utilisateur

Launch

Launch X-431 EURO TURBO Manuel utilisateur

Launch

Launch Creader Professional 233 Manuel utilisateur

Launch

Launch Creader 629 Manuel utilisateur

Launch

Launch Creader Professional 129E Manuel utilisateur

Launch

Launch X-431 PAD VI Manuel utilisateur

Launch

Launch X-431 PROS MINI Manuel utilisateur

Launch

Launch Creader Elite Manuel utilisateur

Launch

Launch iCarScan Manuel utilisateur

Launch

Launch X431 V Manuel utilisateur

Launch

Launch Creader Professional 123 Series Manuel utilisateur

Launch

Launch X-431 GDS Manuel utilisateur

Launch

Launch CRT5011E Manuel utilisateur

Launch

Launch X-431 IMMO Pro Manuel utilisateur

Launch

Launch J-Box 3 Manuel utilisateur

Launch

Launch FX9000 Manuel utilisateur

Launch

Launch CReader 6011 Manuel utilisateur

Launch

Launch Creader Professional 909 Manuel utilisateur

Launch

Launch X-431 PRO3S+ Manuel utilisateur

Manuels Équipement de diagnostic populaires d'autres marques

Mindray

Mindray M7Vet Guide de démarrage rapide

Autel

Autel MaxiProgrammer 201 Manuel utilisateur

TEXA

TEXA TMD2 Manuel utilisateur

Autel

Autel MaxiIM IM608 Manuel utilisateur

Sealey

Sealey BT2012 Manuel utilisateur

Diagnoptics

Diagnoptics Age Reader Manuel utilisateur

LAUNCH TECH

LAUNCH TECH X-431 PRO5 Manuel utilisateur

Hella Gutmann

Hella Gutmann Mega macs X Manuel utilisateur

Foxwell

Foxwell I80TS Manuel utilisateur

KaVo

KaVo 3D eXam Manuel utilisateur

ATEQ

ATEQ VT46 Manuel utilisateur

Hella Gutmann

Hella Gutmann mega macs X Manuel utilisateur

Autel

Autel MaxiFlash VCMI Manuel utilisateur

Qiagen

Qiagen QIAcube Connect MDx Manuel utilisateur

Alber

Alber BDSU Manuel utilisateur

St. Jude Medical

St. Jude Medical QUANTIEN Manuel utilisateur

Bosch

Bosch DCU 100 Manuel utilisateur

Innova

Innova 3568 Manuel utilisateur