Larson Electronics LEDWP-600E-M-E2E-20C Manuel utilisateur

LEDWP-600E-M-E2E-20C

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

Magnetic Mount 60W LED Low Profile Wall Pack w/ Glare Shield

and 20' Cord - 120VAC - 5,400 lumens

Thank you for your purchase of the Larson Electronics LEDWP-600E-M-E2E Wall Pack Light. Please follow

the steps below in order to install, operate and maintain this product.

MOUNTING

The LED wall pack comes pre-assembled and ready to mount via the 200lb. grip magnetic base. A separate

glare shield is available for better directing the light. Follow the guideline below to properly install and operate

the unit.

The wall pack light includes the LED light, trunnion mount, glare shield, and hardware for installing the center

cord grip. Some models may omit hardware depending on selected options.

Ambient Temperature Range: -25°C to +60°

1. Select a location to install the fixture. This LED wall pack is IP68 waterproof, vapor proof, and

built to resist the damaging effects of an outdoor environment. This fixture should not be used in

areas with no ventilation or extreme ambient temperatures.

2. Affix the mount to your chosen metal surface. A 200lb. grip magnetic base allows the unit to

be mounted to any metal surface capable of holding its weight. Run power cord to the

appropriate receptacle with the CORRECT VOLTAGE.

3. Lamp Adjustment. The trunnion mount can be attached to the lamp in two locations, the lower

area or middle area on the back of the wall pack. Use the ( 2 screws ❶) and ( 2 lock washers

❷) for repositioning the mount as shown in the diagram on page 2. The fixture can be placed in

any direction.

WIRING

We strongly encourage a licensed electrician install this product, especially in outdoor locations where

weatherproofing may be required. Universal voltage driver permits operation at 100V - 277V AC, 50 or 60Hz.

Warning: Check product label for correct input voltage!

Attach supply line wires to the appropriate light

fixture wires as shown in the diagram 

This unit comes pre-wired from factory with the

selected cord cap. Plug into matching receptacle

outputting voltage on nameplate. Take precautionary

steps for weatherproofing all connections if installed in

a location where water may come in contact with the

unit. Ensure the unit is properly grounded.

IMPORTANT

READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. THE LEDWP-600E MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND

ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.

WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS

PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,

CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.

RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.

RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.

RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.

WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE

INSTALLATION OR PERFORMING ANY MAINTENANCE.

LEDWP-600E-M-E2E-20C

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

ASSEMBLY

Use the table below for assembling the hardware including the glare shield.

Note: Some hardware shown may not be included depending on final product configuration.

DAISY CHAIN

Daisy chain multiple fixtures by connecting ends. Plug the male cord

cap from next lamp to the female cord cap of first lamp and repeat for

each additional lamp. Plug the first lamp in the daisy chain to a power

outlet to illuminate all attached lamps.

MAINTENANCE

There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the

fixture for proper function.

Disconnect power running to the lamp and be sure the fixture is cool to the touch.

Use a non-abrasive glass cleaning solution to clean the lens.

Note: It is not necessary to open the fixture and clean or touch the LED’s.

Should further information not covered by these instructions be required, please contact Larson Electronics at

1-800-369-6671 for further assistance.

CORD GRIP

MOUNT SCREW

ASSEMBLED UNIT w/Glare Shield

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Larson Electronics Équipement d'éclairage

Larson Electronics

Larson Electronics EXP-LED-1XB-9W Manuel utilisateur

Larson Electronics

Larson Electronics PTB-1-75FT Manuel utilisateur

Larson Electronics

Larson Electronics GSLEDIP6-C1D2 Manuel utilisateur

Larson Electronics

Larson Electronics SLEDB-110V-MS Manuel utilisateur

Larson Electronics

Larson Electronics EPL-AMB-150LED-50 Manuel utilisateur

Larson Electronics

Larson Electronics MMLP-1MLED-12P Manuel utilisateur

Larson Electronics

Larson Electronics EPL-HB-50LED-RT-JB2-6-EPP Manuel utilisateur

Larson Electronics

Larson Electronics EPL-TL-1X10W-C-DF-PA Manuel utilisateur

Larson Electronics

Larson Electronics EPLFL-26W-P-LED-25 Manuel utilisateur

Larson Electronics

Larson Electronics HAL-48-33W-LED-1227-70C Manuel utilisateur

Larson Electronics

Larson Electronics EPL-HB-50LED-RT Manuel utilisateur

Larson Electronics

Larson Electronics EPLC2-HB-50LED-RT Manuel utilisateur

Larson Electronics

Larson Electronics EPL-LB-50LED-RT-180B Manuel utilisateur

Larson Electronics

Larson Electronics EPL-WPLED-150W-RT Manuel utilisateur

Larson Electronics

Larson Electronics EPL-16C-1MLED-50 Manuel utilisateur

Larson Electronics

Larson Electronics LEDP5W-60XC-1227 Manuel utilisateur

Larson Electronics

Larson Electronics EPL-QP-2X50LED-RT-100 Manuel utilisateur

Larson Electronics

Larson Electronics VFD-1P-220.240-1HP-7A-DCM Manuel utilisateur

Larson Electronics

Larson Electronics EPL-50W-120x12-50 Manuel utilisateur

Larson Electronics

Larson Electronics HALPRM-PS-1000WMH Manuel utilisateur

Larson Electronics

Larson Electronics EPLC2-EMG-HB-150LED-RT Manuel utilisateur

Larson Electronics

Larson Electronics EPL-PM-50LED-100 Manuel utilisateur

Larson Electronics

Larson Electronics EPLC2-LED-150W-RT-EB Manuel utilisateur

Larson Electronics

Larson Electronics EPL-LQP-2X150RT Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur