Lark SURFACE SKIMMER Manuel utilisateur
®
WARNING
Safety Care for Children
1. Children, especially children younger than five years, are at high risk of drowning. Drowning occurs silently and quickly and can occur in as little as 2 in (5 cm) of water.
2. Keep children in your direct sight, stay close, and actively supervise them when they are in or near this pool and when you are filling and emptying this pool.
3. When searching for a missing child, check the pool first, even if the child is thought to be in the house.
4. Locate pumps and filters in such a way that children cannot climb on them and gain access to the pool.
5. WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
6. WARNING:To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times by an adult who is capable of
assisting a child in distress.
7. SAVE THESE INSTRUCTIONS.
OWNER′S MANUAL
SURFACE SKIMMER
FOR ABOVE GROUND SWIMMING POOLS
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this product, basic safety precautions should always be followed.
READ AND FOLLOW ALL INFORMATION AND INSTRUCTIONS
Keep for future reference. Failure to follow these warnings and instructions can result in serious injury or death to users, especially children.
Sold & Distributed by Lark Outdoors, Austin, TX USA. Assembly & Service by Polygroup Trading Limited Unit 606, 6th Floor, Fairmont House, No.8 Cotton Tree Drive, Central, Hong Kong.
If you need help or encounter any problems, please call us at (888) 919-0070, between 8am - 5pm MST (extended operating hours may be available during holiday and peak seasons).
© 2020
Thank you for your Lark Outdoors purchase! Should you encounter any problems, please DO NOT return the product to your place of purchase.
For assitance with product setup, parts or troubleshooting, please visit support.polygroupstore.com, or call our customer service team at +1 (888) 919-0070.
All warranty claims and parts requests must be made directly to our service & support partner, Polygroup. Depending on the nature of the concern, you may
be asked to return all or part of the product for inspection or repair. Making it right is our top priority!
READ AND KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
For answers to common questions, setup videos and troubleshooting tips,
please visit our support center at: support.polygroupstore.com,
or call Customer Service at: +1 (888) 919-0070
To order parts, accessories,
and to learn more about our
products, please visit:
www.larkoutdoors.com
DO NOT RETURN PRODUCT TO STORE
PARTS LIST
Part #
Qty.
2 3 4 5 6
11 1 2 1 1 21
P58102301W05 P58102302E09 P5810223AW05 P5810228AW05 P5810224AP0
1
1
P5810227AE09
Key
P5810233AP01
9
P58219221W05
8
Ring Pool
Holding Frame
(Front)
Ring Pool
Holding Frame
(Rear)
Skimmer
Canister Lock Nut Skimmer
Basket
Frame Pool
Holding Frame
Description Adapter Hose ClampHose
P58150036W01
7A
P58102461W01
7B
2
®
Hang the Frame Pool Surface Skimmer onto the top
pole of the frame pool and then turn the Clamp Lock
Screw in clockwise to tighten the Skimmer by hand.
4
Clamp Lock Screw
1
4
5
5
Tighten
Loosen
Loosen the Lock Nut
5
in anti-clockwise by hand
and adjust the position of the Skimmer Canister
1
on the Frame Pool Holding Frame
1
. The position of
the Skimmer Canister
1
should be set as the pool
water surface between the water level marking on the
Skimmer Canister
1
. Tighten the Lock Nut
5
in
clockwise to hold the Skimmer Canister
4
in your
setting position.
If the Suction Sitting of your pool is the same type as
illustrated in 6.1, attach the Adapter to the Suction
Fitting and screw tightly.
6.1 1
9
8
7A
Suction
Fitting
7A
Insert the Skimmer Basket
6
into the Skimmer
Canister
4
. Connect the hose into the hose
connector on the bottom of the Skimmer Canister
4
and fasten the hose by hose clamp.
Turn the Lock Nut
5
in clockwise to tighten the
Frame Pool Holding Frame
1
by hand.
Insert the Frame Pool Holding Frame
1
into the
Skimmer Canister
4
. Put the Lock Nut
5
onto
the screw hole of the Skimmer Canister
4
.
SETUP INSTRUCTIONS
Before assembling your product, please take a few minutes to check the contents and become familiar with all the parts.
A. Frame Pool Surface Skimmer
1
5
4
1
1
5
2
6
4
3
8
9
7A
OWNER′S MANUAL
3
B. Ring Pool Surface Skimmer
Insert the Ring Pool Holding Frame into the Skimmer
Canister
4
and then put the Lock Nut
5
onto the
screw hole of the Skimmer Canister
4
. Tighten the
Lock Nut
5
in clockwise to fix them by hand.
Insert the Ring Pool Holding Frame (Front)
2
into the
Ring Pool Holding Frame (Rear)
3
and then put the
Lock Nut
5
onto the screw hole of the Ring Pool
Holding Frame (Rear)
3
. Tighten the Lock Nut
5
in
clockwise to fix them by hand.
1
53
2
5
4
2
Insert the Skimmer Basket
6
into the Skimmer
Canister
4
.
Connect the hose into the hose connector on the
bottom of the Skimmer Canister
4
and fasten the
hose by hose clamp.
3
6
4
If the Suction Fitting of your pool is the same type as illustrated in 6.2,
remove the Suction Fitting Screen from the Suction Fitting Base first.
Attach the Adapter to the Suction Fitting Base and fix tightly.
Then, connect the Hose
8
to the adapter, and tighten
the Hose Clamp
9
.
6.2 1
7B
9
8
Suction Fitting Screen
Suction Fitting Base
7B
7B
8
9
7
9
8
4
®
Hang the Ring Pool Surface Skimmer onto the top
inflatable ring of the ring pool and then loosen the Lock
Nut
5
in anti-clockwise by hand. Push the Ring Pool
Holding Frame to fix the Ring Pool Surface Skimmer on
the ring pool. (Push the Release Button to loosen the
Ring Pool Holding Frame Rear
3
).
4
5
3
3
5
Push
Release Button
Tighten
If the Suction Fitting of your pool is the same type as illustrated in 6.2,
remove the Suction Fitting Screen from the Suction Fitting Base first.
Attach the Adapter to the Suction Fitting Base and fix tightly.
6.2
9
7B
Suction Fitting Screen
Suction Fitting Base
If the Suction Fitting of your pool is the same type as
illustrated in 6.1, attach the Adapter to the Suction
Fitting and screw tightly.
6.1
7A
9
8
Suction Fitting
7A
7B
Loosen the Lock Nut
5
in anti-clockwise by hand
and adjust the position of the Skimmer Canister
1
on the Ring Pool Holding Frame. The position of the
Skimmer Canister
1
should be set as the pool
water surface between the water level marking on
the Skimmer Canister
1
. Tighten the Lock Nut
5
in clockwise to hold the Skimmer Canister
4
in your
setting position.
5
5
Tighten
Loosen
1
4
7B
8
Then, connect the Hose
8
to the adapter, and tighten
the Hose Clamp
9
.
7
7A
9
8
Autres manuels Lark Pompe de piscine
Manuels Pompe de piscine populaires d'autres marques
Resol
Resol DeltaSol B Pro Manuel utilisateur
Evolution Aqua
Evolution Aqua UniTech Perfect 5000 Manuel utilisateur
Outside Living Industries
Outside Living Industries Ubbink Heatermax Pool Guide de démarrage rapide
CPI
CPI Olympic 2P1815 Manuel utilisateur
Flotec
Flotec FP6121-01 Manuel utilisateur
Pentair
Pentair ONGA LEISURETIME LTP400 Manuel utilisateur