Lanpro LP-1522 Manuel utilisateur

LP1522_M123_ENB01W

Check the box contentment.

Installation Point-to-Point, Multipoint

LP-1522

Access Point and 800mW Router,

with the standard 802.11b/g,

and with PoE technology and external antenna

123 MANUAL INITIAL CONFIGURATION

Screw the antenna as you can see in Figure 2; in case of having an antenna with pigtail

type cable, make sure that antenna cable is plugged into the antenna and then screw the

other end into your SMA connector of your LP-1522. See Figure 3. Note: Never operate

the LP-1522 without the antenna, because you will damage the RF output stage.

Connect the DC electrical power plug into the power jack, see gure 5. The

LP-1522 can be fed alternatively through a LAN port simultaneously with DATA.

For this, you must use a LP-PoE150(*) injector on the side of your Switch or

PC and send Data+Power to the LP-1522 up to 100m distance with our new

LP-CE Cat5e or LP-C6 Cat6 copper UTP cables and 80m distance with LanPro

LP-BMCAT5E bi-metallic UTP Cable, see Figure 6.

(*) The LP-PoE150 Injector is not included.

Connect your PC or Switch to the LAN port of

your LP-1522, as it is shown in Figure 4.

Figure 1

Figure 2

Figure 4

Figure 5

Figure 3

Figure 6

(*) The

LP-PoE150

Injector

is not

included.

www.lanpro.com

Open your selected browser and input the same default address: 192.168.1.254,

as you can see in Figure 7.

In Figure 8, select:

Operation Mode.

Select: Bridge.

Click: Apply Changes.

Once you see the window shown in

Figure 9, indicating “Change setting

successfully!” then click: OK.

Figure 7

Figure 8

Figure 9

In the windows shown in Figure 10,

select: Wireless, Basic Settings,

in: Mode, select: WDS, verify the

channel, because it must be the

same in all equipment, then select:

Apply Changes, the equipment will

restart.

Figure 10

In the windows shown in Figure 11,

select: Wireless, WDS Settings

and the add LAN MAC address

of the routers that will work under

this mode, except the MAC Address

already congured. Remember to

click on: Apply Changes, for each

one of the equipment.

Figure 11

For this conguration you will need MAC addresses of the equipment that will be

part of the Point-to-Point and Multipoint link connection(s).

Once you see the window shown

in Figure 12, indicating “Change

setting successfully!” click: OK,

then: OK, and the equipment will

restart.

Now proceed to set WDS security,

for this, in the windows shown in

Figure 13, select: Wireless, WDS

Settings, Set Security.

Figure 12

A window like the one shown in

Figure 14 will be displayed, in it you

have to set security of this mode. It

is very important to emphasize that

security must be equally congured

in all equipment being part of these

connections.

Figure 14

Figure 13

You must carry out all steps for each

equipment. Likewise, you must

assign each equipment a different

IP address for its administration.

For this, in the window shown in

Figure 15, select the option: TCP/

IP Settings, LAN Interface

and input an IP address in the

segment. We used for this example:

192.168.1.253, this will depend

of your network diagram. Click:

Apply Changes, the equipment will

restart and to access to it, you have

to enter the new IP.

Figure 15

In: Encryption, please enter the

type of encryption you wish, we

recommend WPA2(ES), even

though, verify that all equipment

can support it. Enter a password,

minimum 8 characters. This

password must be the same for

all equipment. Then select, Apply

Changes.

Here you can see a typical Multipoint network diagram, see Figure 16.

Figure 16

Important Recommendation (Optional)

In our Website www.lanpro.com you may be able to see 123 Manuals to congure you

equipment like AP, Point-to-Point, Multipoint, Client and WISP.

Proceed to change the administrative

password of your equipment.

Please select: Management, then:

Password, input the user name

which is Admin, and then type the

new password in: New Password

and type it again in Conrmed

Password. Finally, click on Apply

Changes. In other to access to your

equipment again, you must input

these data once you are asked.

Figure 17

Autres manuels pour LP-1522

Table des matières

Autres manuels Lanpro Point d'accès sans fil

Lanpro

Lanpro LP-1520AI Manuel utilisateur

Lanpro

Lanpro LP-570G Manuel utilisateur

Lanpro

Lanpro LP-1518 Manuel utilisateur

Lanpro

Lanpro LP-288ai Manuel utilisateur

Lanpro

Lanpro LP-C290N Manuel utilisateur

Lanpro

Lanpro LP-1540ai Manuel utilisateur

Lanpro

Lanpro LP-5A Manuel utilisateur

Lanpro

Lanpro LP-1540ai Manuel utilisateur

Lanpro

Lanpro LP-349 Manuel utilisateur

Lanpro

Lanpro LP-C290N Manuel utilisateur

Lanpro

Lanpro LP-1540ai Manuel utilisateur

Lanpro

Lanpro LP-1522 Manuel utilisateur

Lanpro

Lanpro LP-289ai Feuille d'instructions

Lanpro

Lanpro LP-N24 V2.0 Manuel utilisateur

Lanpro

Lanpro LP-1000 Manuel utilisateur

Lanpro

Lanpro LP-C290N Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur